Wilson Electronics Smart Technology 801201-A Manuale utente

Mobile Wireless

Dual Band

Cellular/PCS

Smart TechnologyTM Ampliﬁer

PART# 801201-A

FCC ID: PWO8012ASM

IC: 4726A-8012ASM

Installation Guide

Wilson Electronics, Inc.

3301 E. Deseret Drive, St. George, Utah 84790

For additional technical support go to

www.wilsonelectronics.com

Phone: 1-866-294-1660 Fax: 1-435-656-2432

MOBILE

Wireless

The term “IC:” before the radio certification number signifies

that Industry of Canada technical specifications were met.

Cellular & PCS

Analog & Digital - CDMA, GPRS, GSM, TDMA, 1x, HSDPA

1. PURPOSE OF THE AMPLIFIER

This Wilson Smart Technology™ Ampliﬁer greatly improves signal strength

inside a vehicle without a physical connection to the phone or cellular data card.

It also allows multiple devices to be used simultaneously.

2. PACKAGE CONTENTS

• Bi-Directional Ampliﬁer

• DC plug-in power supply

• Low Proﬁle Antenna

(Coax Included)

• 6’Extension Cable

• Small Antenna

3. HOW THE AMPLIFIER FUNCTIONS

The signal is received by the outside antenna from the cell site. It is thenAMPLIFIED

and transmitted to your phone through the inside antenna. When the phone transmits,

the signal is received by the inside antenna. It is thenAMPLIFIED and transmitted to

the cell site through the outside antenna (not included).

4. AMPLIFIER SYSTEM INSTALLATION (See Illustration on pg. 5)

4.1 Mounting the Ampliﬁer

4.1.1 Select a suitable location to mount the AMPLIFIER. The ampliﬁer

can be mounted to the selected location using screws. (Screws not

included.) Mount the AMPLIFIER away from direct sunlight,

excessive heat and/or moisture. The amplifier needs proper ventilation.

PACKAGE CONTENTS

Bi-Directional

Amplifier

OPTION A

Low Profile

Antenna

(Coax Included)

DC Power

Supply

6' Extension

Cable

OPTION B

Small

Antenna

4.2 Installing the

Wilson Cellular

Inside Antenna (2 options included)

4.2.1A (option A) - The inside antenna should be mounted approximately 1 foot or less

from where the phone is used. The best place to mount the inside antenna is shoulder

height on the side of the drivers seat. The closer the inside antenna is placed to the

phone, the better the performance. See option A.

Do not mount on a surface near metal.

4.2.1B (option B) - For convenience, the Small

Antenna directly attached to the phone will

perform as well as a Direct Connection Ampliﬁer

or similar to the Low Proﬁle antenna attached

directly to the phone. The Small Antenna must be

directly connected to the back of the phone using

Velcro (included). The Small Antenna will not

work away from the phone like the Low Proﬁle

antenna. Connect the 6’extension cable to the Small

Antenna (included). Attach Small Antenna to the

back of the phone. See option B.

4.2.2 Connect the Inside Antenna (A) or 6’ Extension Cable (B) to the side labeled

“INSIDE ANTENNA” on the AMPLIFIER.

Ampliﬁer

Low Proﬁle

Antenna

Ampliﬁer 6’ Extension

Cable Small

Antenna

Small Antenna placement is depen-

dant upon the location of the phones

antenna. Place the SmallAntenna

as close as possible to the phones

antenna.

WARNING: Do not plug the amplifier directly into the phone using a phone specific adapter.

4.3 Installing the

Wilson Cellular

Outside Antenna (Sold Separately)

4.3.1 Select an outside mounting location. For best performance keep the antenna

centered on the vehicle’s roof.

4.3.2 The outside antenna should be located in an area with at least a 12” radius clear

of obstructions, and other radiating elements.

NOTE: If the vehicle has a sunroof, place the outside antenna away from the sunroof so that

the inside antenna is shielded from the outside antenna by metal. This is very important to

avoid oscillation.

4.3.3 Connect the OutsideAntenna to theAMPLIFIER side labeled “OUTSIDEANTENNA”.

NOTE: Do not place the outside antenna in the vehicle without turning the ampliﬁer off.

For example, when at the car wash. This will cause damage to your ampliﬁer.

NOTE: Do not use a glass mounted antenna with a mobile wireless ampliﬁer.

4.4 Connect the DC Power Supply

4.4.1 Connect the large end of the DC Power Supply into your cigarette lighter and the

other end into the input on your ampliﬁer. Use only the supplied power supply.

4.5 Indicators Lights

4.5.1

PWR - Power Indicator Light – Indicates power to the unit.

800 MHz & 1900 MHz dual color Green/Red indicators

Green – Ampliﬁer is operating properly.

Red – Indicates the ampliﬁer is oscillating (needs more separation between

the Inside and Outside Antennas) and/or the cell sites signal is strong and the

ampliﬁer has powered down. (see below)

Oscillation – Try moving the outside antenna to a different location, creating more

separation from the inside antenna. The inside antenna should be mounted within one

foot (1’) of where the cell phone is being used.

Strong Cell Signal – The ampliﬁer is designed to power down when the cell site signal is

strong. If you are installing the ampliﬁer where the cell signal is strong, go to an area with

low signal strength and verify that the light turns to Green.

NOTE: You do not need ampliﬁcation when the cell signal is strong. The ampliﬁer is on

only when the green light is on. In the city, you may only need ampliﬁcation when the

signal fades from buildings or other structures blocking the signal.

MOBILE

AMPLIFIER LAYOUT

Cell Phone(s)

Inside

Antenna

Outside

Antenna

Amplifier DC

Power

Supply

Cell

Site

5. AMPLIFIER SPECIFICATIONS Dual Band 800 / 1900 MHz

Part Number 801201-A

Connectors FME-Male 50 Ohms

Dimensions 5.6 x 3.6 x 1.7 inch or 14.2 x 9.1 x 4.4 cm

Weight 1.44 lbs or 0.65 kg

Frequency 824-894 MHz / 1850-1990 MHz

Gain (up/down) 37 dB / 43 dB

Linear Output Power +30 dBm

Max Output Power 3 watts (Cell Site Controlled)

Max RF (up/down) +35 dBm /+10 dBm

Noise Figure (typical) 3dBnominal

Isolation Uplink/Downlink more than 90 dB

Power Requirements

Ampliﬁer Usage 6 V, 3 A (subject to Uplink power)

6. FEATURES

Advanced Electronics Receive & Transmit Better Than Your Cell Phone

or Cellular Data Card

• Power Control Logic Ensures Maximum Gain is Within Cellular Standards

• Allows Multiple Devices to be Used Simultaneously

• Maximum 3 Watts Output Power (cell site controlled)

• Designed forAll Systems Including CDMA, EDGE, GPRS, GSM, TDMA,

1x, HSDPA

• LED - Power & Overload Shutdown/Oscillation

• Overload Protection Circuit – Protects Cell System from Overload

• Automatic Reset – if overload occurs

7. OPTIONALACCESSORIES/ANTENNA OPTIONS

7.1 Outside Antenna Options

See page 8

8. TECH SUPPORT

If you need further assistance with your installation:

1) Call us Toll-Free at 866-294-1660

2) E-mail tech support at [email protected]

3) Go to www.wilsonelectronics.com

Our Hours of Operation are: 8:00 AM – 4:30 PM (Mountain Time)

The information provided by Wilson Electronics, Inc. is believed to be complete and accurate.

However, no responsibility is assumed by Wilson Electronics, Inc. for any business or per-

sonal losses arising from its use, or for any infringements of patents or other rights of third

9. NOTES & WARNINGS

WARNING: Verify that both the outside antenna and the inside antenna are connected before

powering up the ampliﬁer.

WARNING: Do not place the outside antenna in the vehicle without turning the ampliﬁer off. For

example, when at a car wash. This will cause damage to the ampliﬁer.

WARNING: The outside antenna must be mounted with a separation distance of at least 17 inches from

any of the vehicle occupants or nearby persons and must not be co-located or operating in conjunction

with any other antenna or ampliﬁer. Use of a cellular ampliﬁer with antenna gains higher than 6.12 dBi

is in violation of FCC regulations for which the offender is fully liable. All Wilson Mobile Antennas

are 6.12 dBi or less.

WARNING: The inside antenna must be mounted with a separation distance of at least 1 inch (2.5 cm)

from all persons and must not be co-located in conjunction with any other antenna or ampliﬁer.

WARNING: Do not plug the ampliﬁer directly into the phone using a phone speciﬁc adapter.

WARNING: Do not use a glass mounted antenna with a mobile wireless ampliﬁer

WARNING: Use only the DC Power Supply that comes with the ampliﬁer, or a replacement supplied

by Wilson.

Operation is subject to the following two conditions: (1) This device may not cause interference,

and (2) this device must accept any interference, including interference that may cause undesired

operation of this device.

Leaving the amplifier on in an unused vehicle for days may drain your battery. This can be

avoided by plugging into an ignition switched power source.

The Manufacturer’s rated output power of this equipment is for single carrier operation. For

situations when multiple carrier signals are present, the rating would have to be reduced by 3.5

dB, especially where the output signal is re-radiated and can cause interference to adjacent band

users. This power reduction is to be by means of input power or gain reduction and not by an

attenuator at the output of the device.

In order to prevent excessive input levels from distorting or otherwise overdriving this amplifier,

the maximum uplink RF output is 35 dBm, and the maximum downlink RF output is 10 dBm.

When an input tends to create greater than these maximum levels, a switching circuit will reduce

the RF output by as much as 50 dB.

The voltage and current into the final amplification stage are: TX: 6 V DC 3 A

RX: 3.6 V DC 50 mA

15 DAY

MONEY BACK

GUARANTEE

All Wilson products

have a 15 day

money back

guarantee with

Proof of Purchase

1 YEAR WARRANTY

The Wilson amplifier is warranted for one year against defects in workmanship

and/or materials and will be repaired or replaced, at the discretion of the manufac-

turer, to the original purchaser with dated proof of purchase or sales receipt.

If you have questions about your amplifier please call technical support at

1-866-294-1660 or E-mail [email protected]

Most warranty cases can be handled by taking the amplifier and the re-

ceipt to the store where it was purchased. If inconvenient, the amplifier and a

copy of the receipt, may be sent to the factory, at purchasers expense, where

it may be repaired or replaced and returned shipping paid. Warranty does not

cover damages caused by abuse, misuse, and negligence.

801201A_003 / 03.27.06

Mini

Magnet Mini

Glass NMO

Trucker Magnet

Mount Glass

Mount NMO

Mount RV Trucker

Spring Mount Trucker

Mirror Mount

Dual Band

This device has been designed to operate with the antennas listed below, and having a

maximum gain of 6.12 dB. Antennas not included in this list or having a gain greater than

6.12 dB are strictly prohibited for use with this device. The required antenna impedance

is 50 ohms.

To reduce potential radio interference to other users, the antenna type and its gain should

be so chosen that the equivalent isotropically radiated power (EIRP) is not more than that

permitted for successful communication.

Indice

Altri manuali Wilson Electronics Amplificatore

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 1300 Manuale utente

Wilson Electronics

Wilson Electronics U-Booster 2B5225 Manuale utente

Wilson Electronics

Wilson Electronics 801105 Manuale utente

Wilson Electronics

Wilson Electronics 801102 Manuale utente

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 1300 Manuale utente

Wilson Electronics

Wilson Electronics 2B1401 Manuale utente

Wilson Electronics

Wilson Electronics 271245 Manuale utente

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 4300R Manuale utente

Wilson Electronics

Wilson Electronics 271245 Manuale utente

Wilson Electronics

Wilson Electronics 814001 Manuale utente

Wilson Electronics

Wilson Electronics SIGNALBOOST 811210 Manuale utente

Wilson Electronics

Wilson Electronics BD800AM-M Manuale utente

Wilson Electronics

Wilson Electronics SignalBoost Manuale utente

Wilson Electronics

Wilson Electronics 271245 Manuale utente

Wilson Electronics

Wilson Electronics 801105 Manuale utente

Wilson Electronics

Wilson Electronics WILSONPRO PRO 140i Manuale utente

Wilson Electronics

Wilson Electronics 811101 Manuale utente

Wilson Electronics

Wilson Electronics WILSONPRO ENTERPRISE 4300 Manuale utente

Wilson Electronics

Wilson Electronics 814001 Manuale utente

Wilson Electronics

Wilson Electronics 801247 Manuale utente

Wilson Electronics

Wilson Electronics PRO 710i Manuale utente

Wilson Electronics

Wilson Electronics 271265 Istruzioni operative e di manutenzione

Wilson Electronics

Wilson Electronics 271220 Manuale utente

Wilson Electronics

Wilson Electronics 271247-75 Manuale utente

Manuali Amplificatore popolari di altre marche

ASTRO

ASTRO HVO V40 P Manuale utente

Marantz

Marantz SUPERSCOPE BLA-545 Istruzioni per il montaggio

NAD

NAD CI980 Manuale utente

Technics

Technics SE-CH770 Manuale utente

Harman Kardon

Harman Kardon HK6300 Manuale utente

NAD

NAD T975 Manuale utente

McIntosh

McIntosh MA6850 Manuale utente

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Manuale utente

Viatron

Viatron Autrix Manuale utente

GME

GME GA9800 Manuale utente

Atlas

Atlas CP700 Manuale utente

Roland

Roland KC-1000 Manuale utente

Pyle

Pyle PFMRA350BW Manuale utente

Advantage

Advantage S-250 Manuale utente

IRT Electronics

IRT Electronics DVA-3007 Manuale utente

Dimavery

Dimavery BA-100 Series Manuale utente

Sony

Sony XM-S400D Manuale utente

Schertler

Schertler ROY X Manuale utente