woodmizer Setwork SW Series Manuale utente
Wood-Mizer SW Setworks – A quick reference guide for common functions. Keep near the sawmill for easy reference. Always reference your manual for detailed instructions.
Pattern Mode (Manual) - Cutting dierent sizes
Position blade to top of log
Press (P-1 light activates)
Enter desired size
of bottom board.
Press & enter next
board size. Repeat.
Press to move to starting
height
Save program
Cut
Cutting Modes
Using ABC Programs
Tips
Press & hold desired program
- After nishing a cutting program, press “Exit” to raise the
head for the next log.
- During a program, if you want to use the up/down lever
for manual control over bump up, press “Kerf” button.
A, B, or C
(StrPro is displayed)
Use arrows to select
rst cutting position.
Optional: Change any size.
Press to move to
starting height
Save
Pattern Mode (Quick Program) - Cutting same sizes
Position blade to top of log
Enter desired board size.
Press (StrPro light activates)
Optional: Use arrows to select
board size to change.
Enter a new size.
Move to starting height
Save program
Cut
Remote Mode
Press to activate
or deactivate
Use up/down lever for next cut/bump up.
Cut
Cut
Normal Cutting Mode
Enter board size.
OR use stored board
size in A, B, or C.
Press
Buttons and their Functions
Board size memory buttons.
Program memory buttons.
Conrming a program.
Setting head return height.
Activating Manual Program
mode.
Moving items up.
Activating Quick Program
mode. Moving items down.
Set real distance between the
blade and the sawmill bed.
Deleting a program.
Exit an active function.
Automatically raises head to
clear the cant when returning.
Automatically lowers head.
Storing entered values.
Set blade kerf value.
Remote mode on/o.
Auto-calibration.
Set the input divider value.
Calibrating/Setting Values
Storing New ABC Programs
Press & hold to select
program
Press & hold to delete
old program.
Press & hold to select
program
Enter bottom board size
Push and enter next
board size. Repeat.
Save
ABC Measurements
& hold A, B, or C
Press again A, B, or C.
Input measurements
Save
Set Blade Kerf
Press & hold
Enter value
(2.0mm WM blades)
Save
High/Low Bump Up
Turn on Setworks
As ‘SW-10’ displays,
press & hold
Use arrows to select ‘Hi’ or‘Lo’.
‘Hi’= clearance above last board.
‘Lo’= clearance above cant.
Save
Auto Calibrate Head Height
Set blade height to 150mm
Press & hold
‘Auto Call’ displays
Press. The sawmill will auto-
calibrate itself. ‘End Call’
displays when nished.
Set Input Divider
Turn on Setworks
As ‘SW-10’ displays,
press & hold
Turn on Setworks
As ‘SW-10’ displays, press
LT15 - Enter 20
LT20/40 - Enter 5
Save
Set Actual Blade Height
Press & hold
Enter the correct height
without pausing between
digits.
Save
Height of Head Return
Position head to desired height above cant.
Press until light appears
Press to exit
Verify actual blade height
corresponds with displayed
height.
Indice
Altri manuali woodmizer Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
