Xilinx ML605 Manuale utente
Modifying Xilinx ML605 for Direct JTAG Access 1
©1989-2021 Lauterbach GmbH
Modifying Xilinx ML605 for Direct JTAG Access
TRACE32 Online Help
TRACE32 Directory
TRACE32 Index
TRACE32 Documents ......................................................................................................................
ICD In-Circuit Debugger ................................................................................................................
Processor Architecture Manuals ..............................................................................................
MicroBlaze ...............................................................................................................................
Application Notes for MicroBlaze .......................................................................................
Modifying Xilinx ML605 for Direct JTAG Access ........................................................... 1
Introduction .................................................................................................................... 2
Requirements ................................................................................................................. 2
Description of the Modification ..................................................................................... 3
Testing the Modified ML605 Board ............................................................................... 5
Using ML605 without USB-JTAG Bridge ...................................................................... 6
Pinout of the JTAG to Xilinx ML605 Adaptor ............................................................... 7
Miscellaneous Information ............................................................................................ 8
Modifying Xilinx ML605 for Direct JTAG Access 2
©1989-2021 Lauterbach GmbH
Modifying Xilinx ML605 for Direct JTAG Access
Version 30-Apr-2021
Introduction
The ML605 board does not have a JTAG connector but only a USB-JTAG bridge that is connected to the
host via a standard USB cable. For debugging with TRACE32, the ML605 needs to be modified in order to
make the JTAG signals accessible. This document describes this modification.
The modification was tested and found working by Lauterbach but there is no guarantee
whatsoever. In particular be aware that soldering may cause permanent damage to the board.
Requirements
The following items are used for accessing the JTAG signals on ML605:
• EVB Xilinx ML605
• Xilinx HW-FMC-105-DEBUG daughter board. The daughter board is not strictly required but
serves as a convenient access to the JTAG signals of the main board.
• A Lauterbach “JTAG to Xilinx ML605” adaptor. It may be replaced by a custom-made adaptor. For
details, see the section “Pinout of the JTAG to Xilinx ML605 adaptor”.
• Soldering material
NOTE: While the board is modified for JTAG access, the USB-JTAG bridge is disabled.
See section “Using ML605 without USB-JTAG bridge” for more information.
Modifying Xilinx ML605 for Direct JTAG Access 3
©1989-2021 Lauterbach GmbH
Description of the Modification
This section describes the steps to make the JTAG signals accessible for debugging. The description
assumes a board orientation with the display towards the user (“South”) and the connectors for the adaptor
cards (HMC LCP, HMC HPC) facing away from the user (“North”).
1. The TDO signal (last device) is retrieved by soldering a cable to the left pin of the resistor R296.
The cable is later connected to the free pin on the “PPC to HW-FMC-105-DEBUG” adaptor.
The resistor R296 is located at the front side of the board, close to the south-west corner of the FMC
LPC connector.
2. Disable the driver U88 (SN74LV541APWR) so that the debugger can drive the signals. U88 is
located at the back side in the north-west quadrant of the board.
The driver is disabled by bowing up pin 19 (OE2_N) and connecting it to pin 20 (creating a connection
to VCC). Also connect pins 16 & 17 and pins 13 & 14 so that the debugger can drive the TMS and
TCK nets for the SysACE and Virtex6.
3. Attach the HW-FMC-105-DEBUG daughter board to the FMC-LPC connector J63.
Jumper J17 to “EXC HPC” and J18 to “INC LPC” settings.
Attach the “JTAG to Xilinx ML605” adaptor to J5 on the daughter board.
Connect the cable from R296 to the free “needle” on the “JTAG to Xilinx ML605” adaptor.
Target top view, cable for TDO attached to R296 (left), JTAG to Xilinx ML605 adaptor (right).
In the PDF version, you can zoom into the photo for details.
Modifying Xilinx ML605 for Direct JTAG Access 4
©1989-2021 Lauterbach GmbH
Accidentally pulling on the TDO cable connected to the resistor R296 can easily tear it off and may be
difficult to repair, especially if the pad is also torn off. An improvised cable anchorage with a knot of the cable
in a hole besides the FMC LPC connector was found useful for preventing this.
Target bottom view of the board with the disabled driver U88. The orange cable at the right side of the picture
is not relevant for our purpose (zoom into the photo for details).
Modifying Xilinx ML605 for Direct JTAG Access 5
©1989-2021 Lauterbach GmbH
Testing the Modified ML605 Board
For testing the modified board start a TRACE32 for MicroBlaze or PPC and enter the scan chain diagnostic
command:
The output should be as follows:
If the debugger reports an error, please check that all steps for the modification were done correctly and in
particular a correct setting of the mentioned jumpers.
SYStem.DETECT.DaisyChain ; scan chain diagnostic
JTAG Chain Diagnostics
Sum of length of all IR registers : 18
Number of JTAG devices (BYPASS registers) : 2
IDCODE of device 0 is : 0x0a001093 (Xilinx, XILINX System ACE
controller)
SYS.CONFIG.DRPOST 0. SYS.CONFIG.DRPRE 1.
SYS.CONFIG.IRPOST 0. SYS.CONFIG.IRPRE 10. (IRWIDTH 8.)
IDCODE of device 1 is : 0x64250093 (Xilinx, XILINX Virtex-6 XC6VLX240T)
SYS.CONFIG.DRPOST 1. SYS.CONFIG.DRPRE 0.
SYS.CONFIG.IRPOST 8. SYS.CONFIG.IRPRE 0. (IRWIDTH 10.)
NOTE: Do not use the given configuration settings for debugging MicroBlaze cores. They
do not take into account that only 6 of the 10 bits of the Virtex6’s ID register are
used for accessing the MicroBlaze core.
The correct settings for debugging MicroBlaze are:
SYS.CONFIG.IRPRE 0.
SYS.CONFIG.DRPRE 0.
SYS.CONFIG.IRPOST 12. ;IRPOST bits: 4 unused + 8 SysACE
SYS.CONFIG.DRPOST 1.
Modifying Xilinx ML605 for Direct JTAG Access 6
©1989-2021 Lauterbach GmbH
Using ML605 without USB-JTAG Bridge
While the board is modified for use via a JTAG connector, the USB-JTAG bridge is not functional. This is not
a problem for TRACE32 because it uses the JTAG connector.
For using the Xilinx tools (iMPACT, ChipScope, ...) you can either use a Xilinx Platform Cable connecting to
JTAG (e.g. Xilinx Platform Cable USB) or alternatively use the TRACE32 debug interface as backend for the
Xilinx tools. The latter avoids constantly swapping the cable at the JTAG port when switching between
debugging and configuration.
For doing JTAG accesses with the Xilinx platform cable, you can use the adaptor “JTAG Converter to
Xilinx Target Adapter 14” (LA-3731) which is included with TRACE32 for MicroBlaze, the adaptor “JTAG to
Xilinx ML605”, and a 16-wire ribbon cable as shown in the image below.
For information on setting up the Xilinx tools for using the TRACE32 debug interface for JTAG access,
please refer to the application note “Using TRACE32 as backend for Xilinx tools”.
Modifying Xilinx ML605 for Direct JTAG Access 7
©1989-2021 Lauterbach GmbH
Pinout of the JTAG to Xilinx ML605 Adaptor
The “JTAG to Xilinx ML605” adaptor converts from the pinout of the Lauterbach TRACE32 PPC dongle
(also used for debugging MicroBlaze) to the JTAG header J5 on the HW-FMC-105-DEBUG board.
The design needs to take into account that the FMC daughter boards for ML605 are intended to host
devices inside the JTAG chain i.e. extending the chain by an additional device. The debugger, however,
needs to be at the beginning and the end of the JTAG chain to drive the signals. Therefore the adaptor
connects its TDI line to the TDO signal of the HW FMC 105 DEBUG board. The additional TDO pin on the
adaptor receives the TDO signal of the last device of the board (the Virtex6 FPGA).
PPC dongle J5 on HW-FMC-105-
DEBUG
TDO 1 extra Pin last device TDO
TDI
(TDO_ML605)
36 TDO
(TDO_ML605)
TCK 74 TCK
TMS 99 TMS
VCC 61 VCC
GND 16 2 GND
NOTE: For trouble shooting or JTAG chain diagnostics you might want to connect a
Xilinx platform cable to the HW_FMC_105_DEBUG daughter board. In this
case you also need to cross TDI and TDO as explained above or connect it to
the Lauterbach adaptor.
Modifying Xilinx ML605 for Direct JTAG Access 8
©1989-2021 Lauterbach GmbH
Photo of the “JTAG to Xilinx ML605” adaptor. The red circle marks the extra pin for the last device TDO.
Miscellaneous Information
This section gives some additional information on miscellaneous topics.
• The schematics of the EVB Xilinx ML605 are available from
http://www.xilinx.com/support/documentation/boards_and_kits/xtp052_ml605_schematics.pdf
• The jumper J24 on ML605 cannot be used for JTAG debugging because its JTAG lines are not
connected to the SysACE and FPGA. According to a comment in the board schematics it is only
intended for reprogramming a CPLD during production testing.
Altri manuali per ML605
4
Indice
Altri manuali Xilinx Scheda madre
Xilinx
Xilinx VCU110 Manuale utente
Xilinx
Xilinx ML40 Series Manuale utente
Xilinx
Xilinx Spartan-3E Manuale utente
Xilinx
Xilinx Virtex-7 FPGA VC7222 IBERT Manuale utente
Xilinx
Xilinx AC701 Manuale utente
Xilinx
Xilinx ML505 Manuale utente
Xilinx
Xilinx Kintex UltraScale KCU1500 Manuale utente
Xilinx
Xilinx ZC702 Manuale utente
Xilinx
Xilinx Virtex-6 FPGA Manuale utente
Xilinx
Xilinx ZC702 Manuale utente
Xilinx
Xilinx Zynq ZC702-G Manuale utente
Xilinx
Xilinx ZC702 Manuale utente
Xilinx
Xilinx Spartan-7 SP701 Manuale utente
Xilinx
Xilinx AC701 Manuale utente
Xilinx
Xilinx KC705 Si5324 Manuale utente
Xilinx
Xilinx SP605 Manuale utente
Xilinx
Xilinx ML605 Manuale utente
Xilinx
Xilinx ZCU102 Manuale utente
Xilinx
Xilinx Spartan-3 Manuale utente
Xilinx
Xilinx ML40 Series Manuale utente
Manuali Scheda madre popolari di altre marche
Telit Wireless Solutions
Telit Wireless Solutions SL869-3DR Manuale utente
Gigabyte
Gigabyte GA-9IVDT Manuale utente
Texas Instruments
Texas Instruments ADS8372EVM Manuale utente
Commell
Commell MS-C73 Manuale utente
IBT Technologies
IBT Technologies MB860 Manuale utente
Nvidia
Nvidia TEGRA DG-04927-001_V01 Manuale utente
