Yamaha DX7mega128 Manuale

DX7mega128 Page 1 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

Yamaha DX7mega128 Expansion Install

1: Introduction

The DX7mega128 a powerful option board that provides increased memory and greater control of

the DX7.

While the installation is fairly simple, it still requires patience and general electronics

knowledge. We accept no responsibility for the work you perform on your DX7. Read over

the following installation description and if you feel you are not capable of the work

required, turn the project over to a qualified technician

Precautions!

High Voltage Safety Warning

Unplug the audio cable. Turn the DX7 power switch OFF and unplug it from the wall.

Disconnect any other connected cables before opening the DX7.

ESD Precautions and Proper Handling Procedures

You should observe standard static-safe handling behavior when working with sensitive electronic

equipment such as synthesizers:

o Avoid carpets in cool, dry areas.

o Dissipate static electricity before handling any system components by touching a

grounded metal object.

o If possible, use anti-static devices, such as wrist straps and floor mats.

o Take care when installing the board. Prevent damage to the connectors by aligning

connector pins before you apply pressure. A damaged pin can render the board unusable

and can cause damage to system components at power-on.

o If disconnecting a cable, always pull on the cable connector, not on the cable itself.

Tools Required

o Standard Philips screwdriver.

o Standard flat-head screwdriver (small).

Condition of DX7

While the DX7mega128 will replace the functionality of damaged or missing EPROM and/or

SRAM chips, it will not correct other problems your vintage synthesizer may have. It is

recommended that the synth be in otherwise good condition before beginning the installation. For

instance, the battery voltage should be checked and the battery replaced/repaired by a tech if

necessary. Sockets for the EPROM and SRAM chips should be in good working order and not be

DX7mega128 Page 2 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

dirty, oxidized, rusted or otherwise compromised. If repair is required, do it before installing

DX7mega128.

2: Installation





Back up your patches if they are important to you!

Open the DX7

Using a Philips head screwdriver, remove the 5 screws from the front panel. Two are located

on the left front. Two are located on the right front. A final one is located on the right rear. Set the

screws aside, noting that the rear panel one is the shortest.

(Re)Move the Keybed & Remove the Keyboard Rail

It can be difficult to see the delicate pins when installing the DX7mega128 board. By moving the

keybed (the chassis with the keys) and removing the silver keyboard rail, you will have better

sight lines and freedom of movement when installing the DX7mega128 board.

Remove the 4 large external screws from the underside of the keyboard along the front

edge. The photo below shows the inside front edge of the empty case bottom and illustrates the

location of the 4 screws. You will, of course, be unscrewing from the DX7 underside.

Loosen the 3 internal screws at the extreme right and left ends that hold the keybed in

place. It is not necessary to extract them from the holes they reside in.

DX7mega128 Page 3 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

Carefully lift the keybed slightly up and out (toward yourself) an inch or so.. You don't need

to move it much. You will probably need to free up one or more cables to accomplish it. Or if you

prefer, disconnect the cables and completely remove the keybed.

This will give you access to the 3 screws holding the silver keyboard rail in place. Remove those

three screws and set aside the silver keyboard rail. (Shown here with keybed removed).

You now have excellent

access to the DX7 main

board. If you do remove the

keybed you may find it easier

to remove the small yellow

cable and large flat grayish

cable at the main-board-end

rather than from the keybed.

You will also need to unclip

two small cables on the left

end (mod wheel and pitch

bend). There may also be

wire tires and/or cable

fasteners to deal with.

Remove the EPROM and SRAM ICs

The next step is to remove the EPROM and two SRAM ICs.

The EPROM is found in location IC14 and the two M5M5118P SRAM chips (or similar) are

located at IC21 and IC20.

Remove them by prying slowly at each end of the chip back-and-forth with a small flat-head

screwdriver. Avoid touching any of the metal pins with the screwdriver.

DX7mega128 Page 4 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

Place them safely aside on anti-static foam. You can use the reverse side of the foam shipped

with the DX7mega128.

The photo above shows the 3 chips removed.

After removing the chips, also remove the screw shown at the

center of these photos near IC23.

Install the DX7mega128 Printed Circuit Board

Hand tighten the supplied nylon standoff into the screw position near IC23. Tighten it well by

hand, but there is generally no need to use a tool. Do not over tighten or strip the threads.

Remove the DX7mega128 board from the anti-static foam. Inspect the bottom of the board to

make sure none of the pins have been damaged. You should see one collection of 28 pins (2

parallel strips of 14 pins), one strip of 12 pins and a strip of 8 pins.

DX7mega128 Page 5 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

Place the DX7mega128 board gently on the DX7 main board so that the 28 pins that form a DIP

package align with the vacated IC14 spot. The 8 pins along the edge should align with IC20. Do

not press the board in place yet. You can use a small mirror to check the pin alignment.

Once you are happy that all the pins are aligning with the desired locations, firmly and evenly

press the DX7mega128 board in place. Make a visual check to see that the board is flush with the

sockets.

Using a screwdriver, carefully tighten the original main board screw through the DX7mega128

board into the nylon standoff. Again do not force it or over tighten as this can not only strip

the standoff, but it can cause the DX7mega128 board to change position. It should be tight

enough so that it cannot work lose. Double check the pins.

Reassembly

Remove all tools from the DX7. Carefully reassemble the DX7 in the reverse order, taking care to

replace the correct screws in the various locations. If you disconnected the green keybed ground

strap wire don't forget to screw it back in.

Test

Plug the AC cable in and turn it on. After a few moments, you should get a greeting message like:

* Welcome to *

* DX7mega128 *

DX7mega128 Page 6 of 6 Install v1.20

www.musictechnologiesgroup.com Preliminary

You can do a quick version check of the board by pressing and holding the brown FUNCTION

button and also pressing and holding buttons 16 and 32. You should see something like the

following:

DX7mega128

Version 1.20

Press the green INTERNAL button twice.

Initialization

Since technically the battery has been removed, you may find some of the standard DX7 function

settings have been scrambled. Follow the steps below to put the DX7 into a known good state

before loading your patches back in.

1. Press MEMORY PROTECT / INTERNAL then OFF.

Internal memory protect is now off.

2. Press FUNCTION and then button 13 or button 12 repeatedly until you see FUNCTION

CONTROL Func/Patch. Press NO to set this value to OFF.

There is now one global set of function parameters for the DX7 (later you will see

how to change this so that each patch can have its own function parameters).

3. Press button 13 or 12 again until you see FUNCTION CONTROL Func Data INIT? Press

YES to set the function parameters to the default state.

4. Press button 13 or 12 again until you see FUNCTION CONTROL Volume= and make sure

this level is turned up using the DATA ENTRY slider or YES button.

Check/set the standard DX7 Function settings versus your preferences. You should be able to

load some patches now, but it is still possible that some setting prevents the sound from being

heard.

The patch data memory will certainly be garbled. Use the standard DX7 panel operations to load

the current data bank with your patches. The “Yamaha DX7mega128 Expansion User Guide”

will explain how to select memory banks as well as how to use the other features of this

expansion.

Enjoy your updated DX7!

See the MTG web site for more great vintage synth and drum machine goodies.

Indice

Altri manuali Yamaha Hardware per computer

Yamaha

Yamaha S90 Manuale utente

Yamaha

Yamaha CobraNet MY16-C Manuale utente

Yamaha

Yamaha MY8-AEB Manuale utente

Yamaha

Yamaha PLG150-PF Manuale utente

Yamaha

Yamaha GC2020BII Manuale utente

Yamaha

Yamaha PLG150-VL Manuale utente

Yamaha

Yamaha F1030 Manuale utente

Yamaha

Yamaha DMP7 Manuale utente

Yamaha

Yamaha SP2060 Manuale utente

Yamaha

Yamaha PLG150-AN Manuale utente

Yamaha

Yamaha GQ1031 Manuale utente

Yamaha

Yamaha MMP1 Manuale utente

Yamaha

Yamaha DSP-1 Manuale utente

Yamaha

Yamaha PLG100-VH Manuale utente

Yamaha

Yamaha SPX90 II Manuale utente

Yamaha

Yamaha mLAN8E Manuale utente

Yamaha

Yamaha PLG100-DX Manuale utente

Yamaha

Yamaha PLG150-AN Manuale utente

Yamaha

Yamaha DX7-4X-EXP Manuale utente

Yamaha

Yamaha MTX5-D Manuale utente

Yamaha

Yamaha DME Series Guida utente

Yamaha

Yamaha mLAN16E2 Manuale utente

Yamaha

Yamaha MTX3 Manuale utente

Yamaha

Yamaha mLAN8P Manuale utente

Manuali Hardware per computer popolari di altre marche

EMC2

EMC2 VNX Series Manuale del proprietario

Panasonic

Panasonic DV0PM20105 Manuale utente

Mitsubishi Electric

Mitsubishi Electric Q81BD-J61BT11 Manuale utente

Gigabyte

Gigabyte B660M DS3H AX DDR4 Manuale utente

Raidon

Raidon iT2300 Manuale utente

National Instruments

National Instruments PXI-8186 Manuale utente

Hauppauge

Hauppauge WinTV-HVR-2250 Manuale utente

Kontron

Kontron CP6002 Manuale utente

Manhattan

Manhattan 702843 Manuale utente

Aphex

Aphex 230 Manuale utente

AMD

AMD Phenom II Manuale operativo

Intel

Intel NUC 12 Pro Manuale utente

dbx

dbx Zone Pro 1260 Manuale utente

Galaxy

Galaxy GHDX2-2430S-24F4D Manuale utente

Intel

Intel AXXRMFBU4 Manuale utente

Kontron

Kontron DIMM-PC/MD Manuale utente

ST X-NUCLEO-SAFEA1B Istruzioni operative

STEINWAY LYNGDORF

STEINWAY LYNGDORF SP-1 Manuale utente