Zebex Z-3152 Series Istruzioni operative

Settings and Programming

For

2D Image Scanners

No warranty of any kind is made in regard to this material, including, but not

limited to, implied warranties of merchantability or fitness for any particular

purpose. We are not liable for any errors contained herein nor for incidental

or consequential damages in connection with furnishing, performance or use

of this material. We shall be under no liability in respect of any defect arising

from fair wear and tear, willful damage, negligence, abnormal working

conditions, failure to follow the instructions and warnings, or misuse or

alteration or repair of the products without written approval. No part of this

document may be reproduced, transmitted, stored in a retrieval system,

transcribed, or translated into any human or computer or other language in

any form or by any means electronic, mechanical, magnetic, optical,

chemical, biological, manual or otherwise, except for brief passages which

may be quoted for purposes of scholastic or literary review, without express

written consent and authorization. We reserve the right to make changes in

product design without reservation and without notification. The material in

this guide is for information only and is subject to change without notice. All

trademarks mentioned herein, registered or otherwise, are the properties of

their various, ill, assorted owners.

General handling precautions

Do not dispose of the scanner in fire.

Do not put the scanner directly in the sun or by any heat source.

Do not use or store the scanner in a very humid place.

Do not drop the scanner or allow it to collide violently with other objects.

Do not take the scanner apart without authorization.

Radio Frequency Interference Requirements

This equipment has been tested and found to comply with the limits for a

Class B digital device, pursuant to part 15 of the FCC rules. These limits are

design to provide reasonable protection against harmful interference in a

residential installation. This equipment generates, uses and can radiate

radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications.

However there is no guarantee that interference will not occur in a particular

installation. If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or

more of the following measures:

Re-orientate the receiving antenna

Increase the separation between the equipment and receiver

Connect the equipment into an outlet on a circuit different from that to

which the receiver is connected

Consult the dealer or an experienced radio/TV technician for help.

For CE-Countries:

It is in conformity with the CE standards. Please note that a CE-Marked

power supply unit should be used to conform to these standards.

Laser Devices

The devices using lasers comply with US 21CFR1040.10 and 1040.11

except for deviations pursuant to Laser Notice No. 50 dated July 26, 2002

and IEC608525-1:+A1:1997+A2:2001 The laser classification is marked on

one of the labels on the devices.

Class 1 Laser devices are not considered to be hazardous when used for

their intended purpose. The following statement is required to comply with

US and international regulations:

Caution: Use of controls, adjustment or performance of procedures other

than those specified herein may result in hazardous laser light exposure.

Class 2 laser scanners use a low power, visible light diode. As with any

bright light source, such as the sun, the user should avoid staring directly

into the light beam. Momentary exposure to a Class 2 laser in not known to

be harmful.

ImportantNotice

1. This document is in A5 size. Please check your printing setting before

printing it out.

2. When printing barcodes for programming, the use of a high-resolution

laser printer is strongly suggested for the best scan result.

3. The settings shall be updated periodically without prior notice. For the

latest version, please contact your authorized distributor.

SettingsandProgramming

Scan a series of selected barcode patches in this manual to affect setup and

programming of your handheld 2D Image Reader. Decoding options and

interface protocols can be tailored to a specific application. Setup

parameters are stored in non-volatile memory in the scanner and are

retained even when power is off. Setup parameters change only when you

reset them.

Throughout the programming guide, default values are indicated with square.

You may need to hide adjacent code patches with your hand when scanning.

ProgrammingOptions

This section contains the following two divisions:

Default factory device settings.

Supported symbologies.

DefaultFactoryDeviceSettings

User Preferences

Parameter Default

Set Default Parameter All Defaults

Parameter Scanning Enable

Beeper Tone Medium

Beeper Volume High

Handheld/Hands-free Scanner Level

Trigger Mode Scan Module Presentation

Handheld/Hands-free Scanner Low Power

Power Mode Scan Module Continuous on

Time Delay to Low Power Mode 1.0 Sec

Decode Session Timeout 9.9 Sec

Timeout Between Decodes, Same Symbol 0.6 Sec

Beep After Good Decode Enable

Presentation Mode Session Timeout 2 Seconds

User Preferences

Set Default Parameter

Scan this bar code to return all parameters to the default values.

Set All Defaults

Parameter Scanning

To disable decoding of parameter bar codes, including the Set All Defaults

parameter bar code, scan the Disable Parameter Scanning bar code below. To

enable decoding of parameter bar codes, scan Enable Parameter Scanning.

Enable Parameter Scanning

Disable Parameter Scanning

Beeper Tone

To select a decode beep frequency (tone); scan the Low Frequency, Medium

Frequency, or High Frequency bar code.

Low Frequency

Medium Frequency (Optimum

Setting)

High Frequency

Beeper Volume

To select a beeper volume, scan the Low Volume, Medium Volume, or High

Volume bar code.

Low Volume

Medium Volume

High Volume

Trigger Modes

Level Mode - A trigger event activates decode processing, which

continues until the trigger event ends, a valid decode, or the

decode session time-out is reached. This scan mode is not

available for scan module.

Presentation Mode - When the device detects an object in its field

of view it triggers and attempts to decode. The range of object

detection does not vary under normal lighting conditions. This

applies to decode mode only. In this mode the unit does not enter

its sleep state.

Host Mode- A host command issues the triggering signal. The

device interprets a trigger pull as a level triggering option. This scan

mode is not available for scan module.

Level Mode

(Default for handheld/hands-free

scanners.)

Presentation Mode

(Default for scan module.)

Host Mode

Power Mode

This parameter determines whether or not power remains on after a decode

attempt. In low power mode, the decoder enters into a low power consumption

mode to preserve battery life after each decode attempt. In continuous power

mode, power remains on after each decode attempt.

Continuous On

(Default for scan module)

Low Power Mode

(Not available for scan module)

Time Delay to Low Power Mode

This parameter sets the time the decoder remains active after decoding. The

decoder wakes upon trigger pull or when the host attempts to communicate

with the decoder.

Note: 1. This parameter only applies when Power Mode is set to Low Power.

2. This setting is not available for scan module since it is always in

presentation mode and its power is continuous on.

1 Second

5 Seconds

1 Minute

5 Minutes

15 Minutes

1 Hour

Indice

Altri manuali Zebex Lettore di codici a barre

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente