ZURN 350 Manuale utente
INST2018_Model350_65-250 Rev. 11/18 ZURN.COM.AU
ZURN WILKINS BACKFLOW
Double Check Valve Assembly
INSTALLATION & MAINTENANCE
MODEL 350 65-250mm
INSTALLATION INSTRUCTIONS
CAUTION: Installaon of Backflow Preventers must be performed
by qualified, licensed personnel. The installer should be sure
the proper device has been selected for the parcular installa-
on. Faulty installaon could result in an improperly funcon-
ing device.
-ZURN WILKINS Model 350 Double Check Valve assemblies are
for use on potable water lines where a health hazard does
exist in the event of a backflow situaon.
-Damage to the device could result wherever water hammer
and/or water thermal expansion could create excessive line
pressure. Where this could occur, shock arrestors, check valves
and/or pressure relief valves should be installed downstream
of the device.
-If installaon is in a pit or vault, the Backflow Preventer must
never be submerged in water because this could cause a
cross-connecon. Make sure that the pit or vault always
remains dry by providing ample drainage.
1. Before installing a Model 350 Backflow Preventer, flush the
line thoroughly to remove all debris, chips and other foreign
maer. If required, a strainer should be placed upstream of the
Backflow Preventer. CAUTION: Do not use a strainer in seldom
used emergency waterlines such as fire lines.
2. Provide adequate space around the installed unit so that the
test cocks will be accessible for tesng and servicing.
3. Install valve at least 300mm above surrounding flood level.
4. Always consult local codes for installaon methods, approvals
and guidance.
5. Resilient seated shutoff valves are required to be installed on
both the inlet and outlet of the device to make field tesng
possible.
WARRANTY: ZURN WILKINS Valves are guaranteed against defects of material or workmanship when used for the services recommended. Please
refer to the LWG Zurn/ Zurn Wilkins Product Warranty Statement for details.
PERFORMANCE
1200kPa
60 Celsius
2400kPa
MODEL 350 FEATURES
Max. Working Water Pressure
Max. Working Temperature
Hydrostatic Test Pressure
End Connections Flanged
WATERMARK
AS/NZS 2845.1
LIC. 1379
TYPE
TESTED
AS/NZS 4020
LIC. 20111
STANDARDS COMPLIANCE
-Australian Watermark (AS/NZS 2845.1) Approved Lic. 1379
-Type Tested AS/NZS 4020 Lic. 20111
PLACING THE DEVICE IN SERVICE
1. Start with both shut-off valves closed. Slowly open the inlet
shut-off valve unl the backflow preventer is completely
pressurized.
2. When the unit has been pressurized, vent any trapped air by
slightly opening each of the four test cocks.
3. Slowly open the downstream shut-off valve. The Model 350
Double Check Valve assembly is now in service.
4. Aer the Model 350 has been properly installed, test the device
(see “TEST PROCEDURES”). If the device fails the test, remove
the first and second check valves and thoroughly flush the
device. Clean rubber and seats of all debris and place unit back
in service.
65, 80 & 150mm 200 & 250mm
OUTDOOR INSTALLATION: The Model 350 Backflow Preventer may be installed outdoors only if the device is protected against
freezing condions. Exposure to freezing condions will result in improper funcon or damage to the device. The installaon locaon
must be kept above 0°C. All the basic installaon instrucons apply.
DIRON OF F
L
O
W
�
WILKINS MODEL 350
DIRON OF F
L
O
W
�
WILKINS MODEL 350
INST2018_Model350_65-250 Rev. 11/18 ZURN.COM.AU
ZURN WILKINS BACKFLOW
Double Check Valve Assembly
INSTALLATION & MAINTENANCE
MODEL 350 65-250mm
TESTING PROCEDURES
TEST NO. 1 - TIGHTNESS OF #1 CHECK VALVE
REQUIREMENT:
The stac pressure drop across check valve #1 shall be at least
1.0 psid. If test cock #3 is not at the highest point of the check
valve body, then a vercal tube must be installed on test cock
#3 so that it rises to the top of the check valve body.
PROCEDURE:
1. Slowly open all 4 test cocks to remove any foreign material and
aach fings.
2. Aach hose from the high side of the test kit to the #2 test
cock.
3. Open test cock #2 and bleed all air from the hose and gauge
by opening the high side bleed needle valve. Close high side
bleed needle valve. If a tube is aached to test cock #3, open
test cock #3 to fill the tube. Close test cock #3. Close #2
shut-off valve then close the #1 shut-off valve.
4. Hold gauge at same level as test cock #3 or water level in tube.
Slowly open test cock #3. Record the stac pressure drop
across check valve #1 aer gauge reading stabilizes and water
stops running out of test cock #3.
5. Close all test cocks, open shut-off valve #1 and remove test
equipment.
TEST NO. 2 - TIGHTNESS OF #2 CHECK VALVE
REQUIREMENT:
The stac pressure drop across check valve #2 shall be at least
1.0 psid. If test cock #4 is not at the highest point of the check
valve body, then a vercal tube must be installed on test cock
#4 so that it rises to the top of the check valve body.
PROCEDURE:
1. Aach hose from the high side of the test kit to the #3 test
cock.
2. Open test cock #3 and bleed all air from the hose and gauge by
opening the high side bleed needle valve. Close high side bleed
needle valve. If a tube is aached to test cock #4, open test
cock #4 to fill the tube. Close test cock #4. Close #1 shut-off
valve.
3. Hold gauge at same level as test cock #4 or water level in tube.
Slowly open test cock #4. Record the stac pressure drop
across check valve #2 aer gauge reading stabilizes and water
stops running out of test cock #4.
4. Close all test cocks, slowly open shut-off valve #1 & #2 and
remove test equipment.
EQUIPMENT REQUIRED: Differenal pressure gauge test kit.
VENT HOSE
LOW SIDE HOSE
HIGH SIDE HOSE
LOW SIDE BLEED
NEEDLE VALVE
#1 TEST COCK
#4 TEST COCK
#3 TEST COCK
#2 TEST COCK
#2 SHUT-OFF
VALVE
#1 SHUT-OFF
VALVE HIGH SIDE BLEED
NEEDLE VALVE
INST2018_Model350_65-250 Rev. 11/18 ZURN.COM.AU
ZURN WILKINS BACKFLOW
Double Check Valve Assembly
INSTALLATION & MAINTENANCE
MODEL 350 65-250mm
SERVICING CHECK VALVES
Aach a ratchet wrench, 17mm deep socket, and a 100mm
long extension are recommended for removing check
assemblies.
1. Close inlet and outlet shut-off valves.
2. Open No. 2, No. 3 and No. 4 test cocks to release pressure
from valve.
3. Loosen & remove the grooved coupling around the access
cover. Remove cover.
4. To service only the #1 check assembly, remove the 6 bolts,
washers and o-rings from the back of the #1 check assembly.
Separate the retainer and the seal ring from the check
assembly and proceed to step #8.
5. To service both checks or the #2 check, the #1 check assembly
must first be removed. Remove the 4 nuts and washers
retaining the #1 check assembly. Remove the #1 check
assembly from the body.
6. To remove the #2 check assembly, remove the 7 nuts,
washers and the #2 check retaining ring. Grasp the check
assembly by the stem and remove from valve.
7. Remove all 6 bolts, washers and o-rings from the check
assembly (See “Check Assembly” illustraon). Separate
retainer from check assembly to expose seal ring for inspec-
on.
8. Inspect the rubber seal ring for cuts or embedded debris. If
the reverse side of the seal ring is unused, it is possible to
invert the seal ring. This would be considered a temporary
soluon to fixing a fouled check and should be replaced with
a new seal ring as soon as possible.
9. Inspect valve cavity and seang areas. Remove any debris.
10. Reverse the above procedures to reinstall check assemblies.
Lubricate seat o-rings to hold them in place while reinstalling
seat. Place washers on studs and ghten retaining nuts
evenly.
11. Reinstall access cover and grooved coupling.
NOTE:
If any poron of the seat assembly is damaged or missing or if
the seat sealing rib is damaged in any way, do not aempt to
field repair it. Contact your local ZURN WILKINS representa-
ve for assistance.
CHECK ASSEMBLY
SEAT ASSEMBLY
SEAL RING
O-RING
(BOLT)
SEAL RETAINER
WASHER
BOLT
CHECK HANDLE
O-RING (SEAT)
65 & 80mm
100 & 150mm
SEAT ASSEMBLY
SEAL RING
O-RING
SEAL RETAINER
WASHER
NUT
O-RING (SEAT)
SEAT ASSEMBLY
SEAL RING
O-RING
(BOLT)
RETAINER
WASHER
BOLT
200 & 250mm
All Model 350 Double Check Valve Backflow Preventers must be
inspected and maintained by licensed personnel at least once a
year or more frequently as specified by local codes. Replace-
ment of worn or damaged parts must only be made with
genuine “ZURN WILKINS” parts.
GENERAL MAINTENANCE
1. Clean all parts thoroughly with water aer disassembly.
2. Carefully inspect rubber seal rings and o-rings for damage.
3. Test unit aer reassembly for proper operaon (refer to
“TESTING PROCEDURES”).
INST2018_Model350_65-250 Rev. 11/18 ZURN.COM.AU
ZURN WILKINS BACKFLOW
Double Check Valve Assembly
INSTALLATION & MAINTENANCE
MODEL 350 65-250mm
#2 PLATE RETAINER (4” & 6”)
(PLASTIC RETAINER MODELS 21/2” & 3”)
#2 CHECK ASSEMBLY
FIGURE 1 FIGURE 2 FIGURE 3
#1 CHECK ASSEMBLY
#1 RETAINER
GASKET
SERVICING CHECK VALVES cont ’d
PROBLEM POSSIBLE CAUSES CORRECTIVE ACTION
LEAKING CHECK VALVES 1. Debis on seat or seal ring 1. Clean seat area
2. Damaged seat area 2. Replace check assembly
3. Damaged seat o-ring 3. Replace seat o-ring
4. Damaged bolt o-ring(s) on check retainer 4. Replace o-ring(s)
LOW OR NO FLOW 1. Device installed backwards 1. Verify flow direcon arrow
2. Gate valves not fully open 2. Turn handles counter-clockwise
3. Low supply pressure 3. Aach pressure gauge to testcock
#1 & verify pressure
TROUBLESHOOTING
INST2018_Model350_65-250 Rev. 11/18 ZURN.COM.AU
ZURN WILKINS BACKFLOW
Double Check Valve Assembly
INSTALLATION & MAINTENANCE
MODEL 350 65-250mm
PERFORMANCE CHARACTERISTICS
MODEL 350 65, 80 & 100mm
0
0
35
69
104
12.6 25.2 37.9 50.5
FLOW RATES (l/s)
PRESSURE LOSS kPa
65mm 80mm
100mm
MODEL 350 150 & 200mm
0
35
69
104
25.2 50.5 75.7 100.9 126.2 151.4
FLOW RATES (l/s)
150mm
200mm
0
0
35
69
104
63.0 126.0 189.0 252.0
MODEL 350 200 & 250mm
PRESSURE LOSS (kpa)
200mm
250mm
0
PRESSURE LOSS kPa
FLOW RATES (l/s)
Indice
Altri manuali ZURN Unità di controllo
ZURN
ZURN 350AST Series Manuale utente
ZURN
ZURN AquaSense ZER-W2 Series Manuale utente
ZURN
ZURN WILKINS 450 Manuale utente
ZURN
ZURN Wilkins ZW109BP Manuale del proprietario
ZURN
ZURN ZW215FP Manuale di installazione
ZURN
ZURN WILKINS ZW109FP Manuale del proprietario
ZURN
ZURN AquaVantage ZH Series Manuale utente
ZURN
ZURN Aquaflush Z6001 Manuale utente
ZURN
ZURN Metroflush Z6200 series Manuale utente
ZURN
ZURN AquaSense ZER-SM Series Manuale utente
ZURN
ZURN AquaSense ZTR Series Manuale utente
ZURN
ZURN WILKINS BR4EC Manuale utente
ZURN
ZURN QHCMKIT5 Manuale utente
ZURN
ZURN ZER6000AV-CPM Manuale utente
ZURN
ZURN LEAD-FREE ZW209 Manuale
ZURN
ZURN AQUA-GARD ZW1070/15 Guida alla manutenzione e all'assistenza
ZURN
ZURN WILKANS PV-PRD Manuale utente
ZURN
ZURN AquaSense ZER-SM Series Manuale utente
ZURN
ZURN TEMP-GARD III Z7300-SS-MT-HW-H9 Manuale utente
ZURN
ZURN TEMP-GARD Z7100 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
