Zycoo SH30 Manuale utente
Quick Installation Guide
SH30
Network Horn Speaker
Packing List
M5*45
ø8*40
Network Horn Speaker (1PCS)
M5*45 screws with anchors (3 PCS each) Quick Installation Guide (1PCS)
Power Adaptor (optional)Warranty Card (1PCS)
01
安装方式
图一
120
φ64.0mm
φ5.0mm
1、将设备的“安装螺栓”拆除，将喇叭与底座分离开；
、根据（图一）尺寸在安装面上钻三个安装孔 ；2，膨胀管规格为ø8*40mm
、3使用塑料锤将膨胀管打进所钻的孔里面；
4、将设备底座的固定孔对准膨胀管，使用镙钉KA5*45将进行固定。必须确保设备是安全地安装到安装平面上；
5、将“安装螺栓”重新连接上，并安全地拧紧“安装螺栓”，使喇叭与底座紧固在一起；
6、松开“角度调节旋钮”约75%，但不要折卸开，旋转设备到需要的角度后，拧紧“角度调节旋钮”；
7、连接电源线及网线。
安装螺栓
角度调节旋钮
底座
中 文
02
安装角度
系统登录导向
1.连接好电源（或PoE）及网线。
2.设备启动完成后，按下恢复出厂设置按键5秒后，松开按键，设备进行IP播报。出厂默认DHCP，若未获取到IP地址，则
默认登录IP地址为192.168.1.101。直接在浏览器地址栏输入IP地址，即可进入设备登录界面，设备的缺省用户名及密码均
为admin。
!
90°
1、调节喇叭角度时需要注意，喇叭口不可向上，不可垂直向下；
2、建议调节角度斜向下约 °。60
~60°
03
恢复出厂设置导向
长按恢复出厂设置按键10秒以上，听到语音提示后松开，设备进入恢复设置状态，系统指示灯熄灭。恢复成功后，系统运
行指示灯进入闪烁状态。
直流电源24V输入
恢复出厂设置按键
以太网接口
系统运行指示灯
04
English
Installation
Figure 1
120
φ64.0mm
φ5.0mm
1.Separate the speaker and the pedestal.
2.Use an 8 mm drill to drill 3 mounting holes for the pedestal as shown in Figure 1.
3.Push the anchors into the mounting holes and tighten then with a rubber hammer.
4.Install the pedestal to the mounting holes and fix with KA5*45 screws.
5.Install the horn speaker back to the pedestal and tighten the bolt.
6. Loose the angle adjustment knob to adjust the speaker angle, after you get a perfect angle, then tighten the knob.
7.Connect network cable and power supply.
Speaker Fixing Bolt
Angle Adjustment Knob
Pedestal
05
Speaker Angle
Web Login
1.Connect network cable and power supply (if PoE is not enabled on the network cable).
2.Wait for 30 seconds then press and hold the RST button for 5 seconds and release, it will announce the IP address
obtained from the DHCP server. If there’s no DHCP server or DHCP fails, it will use default IP 192.168.1.101. In the
browser address bar input the IP address you hear to open its web management interface. Default username and
password admin/admin.
!
90°
1.It’s not recommended to angle the speaker upwards or straightly downwards.
2. Approximately 60 degrees angle with vertical direction downwards is recommended.
~60°
06
Interfaces and Instructions
To reset factory defaults, press and hold the RST button for 10 seconds (5 seconds for IP address announcements)
and release, now you should hear voice prompts “Resetting factory defaults, rebooting…”, it means the speaker will
now reset.
24V DC power Interface
Reset Button
Ethernet Interface
System LED Indicator
07
Installation
Figure 1
120
φ64.0mm
φ5.0mm
1. Séparez le haut-parleur et le piédestal.
2.Utilisez un foret de 8 mm pour percer 3 trous de montage pour le piédestal, comme illustré à la figure 1.
3.Enfoncez les chevilles dans les trous de montage et serrez-les ensuite avec un marteau en caoutchouc.
4.Installez le socle dans les trous de montage et fixez-le avec des vis KA5 * 45.
5.Installez le haut-parleur sirène sur le socle et serrez le boulon.
6. Desserrez le bouton de réglage de l'angle pour régler l'angle du haut-parleur, après avoir obtenu un angle parfait,
puis serrez le bouton.
7.Connectez le câble réseau et l'alimentation.
Boulon de fixation d'enceinte
Bouton de réglage d'angle
Piédestal
Français
08
Indice
Lingue:
Altri manuali Zycoo Altoparlanti
Zycoo
Zycoo SC15 Manuale utente
Zycoo
Zycoo SQ10 Manuale utente
Zycoo
Zycoo SC15 Manuale utente
Zycoo
Zycoo SC10 Manuale utente
Zycoo
Zycoo SC15 Manuale utente
Zycoo
Zycoo SL50 Manuale utente
Zycoo
Zycoo SL30 Manuale utente
Zycoo
Zycoo SW15 Manuale utente
Zycoo
Zycoo SC15 Manuale utente
Zycoo
Zycoo SQ10 Manuale utente
