3D Systems CUBE Manuale utente
3rd Generation
Personal 3D Printer
Quick Start Guide
See Inside for Use and Safety Information
The USB Mass Storage Device Contains the User Guide and
Quick Start Guide in other Languages
Congratulations on the purchase of your new Cube® 3D Printer! This Quick Start Guide has the use and
safety information you need to get started. Welcome to the 3D creative revolution – let the possibilities
begin!
If you have any questions, do not hesitate to reach us at cubifysupport@cubify.com.
This Quick Start Guide will give you basic instructions on how to get your Cube®3D Printer plugged in
and printing so you can start making your own creations.
For more detailed instructions, refer to the Cube®User Guide located on your USB
mass storage device.
CONTENTS
SAFETY ........................................................................................................................ 1
YOUR CUBE AT A GLANCE ........................................................................................ 2
UNPACK YOUR CUBE................................................................................................. 3
What’s Included .........................................................................................................................6
SETTING UP AND ACTIVATING YOUR CUBE ........................................................... 7
FINISHING YOUR CREATION ................................................................................... 23
Removing your Creation from the Print Pad.........................................................................23
Removing Supports and Rafts (If Required).........................................................................23
MAINTENANCE.......................................................................................................... 24
Print Pad Maintenance............................................................................................................24
Gap Verication .......................................................................................................................26
Manual Gap Adjustment .........................................................................................................28
1
SAFETY
HOT SURFACE HAZARD: A HOT SURFACE IS ACCESSIBLE IN THE VICINITY OF THIS
SIGN OR AT THE PRINT JET. AVOID CONTACT WITH THESE AREAS. HOT SURFACES
CAN CAUSE SEVERE BURNS.
Caution: Indicates something may happen that could cause loss of data,
damage to equipment, or could cause personal injury.
Caution: Indicates a pinch point hazard that could cause personal injury.
• Follow all safety rules in this section and observe all cautions and warnings in this guide.
• DO NOT modify any safety features or make modications to the Cube. Doing so is prohibited and
voids your warranty.
• Use of print materials other than 3D Systems print materials and genuine 3D Systems components
may void warranty.
• Adult supervision is required; observe children closely and intervene as necessary to prevent
potential safety problems and ensure the appropriate use of the Cube. Ensure small 3D prints are
not accessible to young children. These 3D prints are potential choking hazards for young children.
• DO NOT change a material cartridge during printing; doing so may damage the Cube.
WARNING: DO NOT TOUCH THE PRINT JETS DURING SETUP AND OPERATION. THE
PRINT JETS BECOME VERY HOT.
Caution: DO NOT unplug the Cube while the print jet is hot. Refer to the
touchscreen to determine when the print jets are cool enough.
CAUTION: Read and follow all instructions prior to setting up the printer.
To ensure safety, please exercise caution when operating your printer. Read and follow all safety
precautions as outlined in this document and the Cube User Guide. Be careful when operating your
Cube 3D Printer to ensure proper printing and be mindful of and avoid hot surfaces.
2
YOUR CUBE AT A GLANCE
B
A
Print Jets
B
Print Jet Tubes
C
Material Cartridges
D
Print Pad
E
Print Platform
F
Touchscreen Display
G
On / Off Button
H
USB Inlet Port (mass
storage device only)
I
Power Inlet
J
Refuse Bins with
Wipers
B
CC
DE
F G
I
H I
H
A
J
3
UNPACK YOUR CUBE
NOTE: Keep all packing materials for future transport. Shipping the printer without
the original packing materials may damage the printer and void the manufacturer’s
warranty.
1. Pull the clips (A) and remove them from the top of the
printer box and open the box.
2. Remove the upper foam support.
3. Remove the printer from the box and remove the
protective bag from the printer. Place the printer on a
solid, level base.
NOTE: When installing the printer there must
be a minimum of 8” (203 mm) of space on top
and on either side of the printer.
NOTE: There must be a minimum of 4” (102
mm) space in front of and behind the printer.
A
4
8” (203 mm)
8” (203 mm)
8” (203 mm)
Hand Clearance Around the Printer Build Plate Travel Area
4” (102 mm)
4” (102 mm)
Back
Front
Front View Top View
4. Remove the top insert.
5. Fold the sides inward and remove the lower insert from
the printer.
5
6. Raise the print platform (A) and remove the spacer (B)
from the printer.
7. Open the accessories box and unpack the material cartridges, the USB mass storage device,
the power supply, cord, and the Cube Glue bottle.
8. Connect the power supply cable to the power inlet port
(A) on the printer.
NOTE: The cable should lock in place. To
remove the cable, pull back on the outer cable
end and carefully pull it out from the printer.
9. Connect the power cord to utility power and to the power
supply.
NOTE: Ensure the connection is secure.
10. Power on the printer by pressing the button (A) next to
the touchscreen display.
A
A
B
A
6
WHAT’S INCLUDED
1Depending on your printer model or conguration, up to two cartridges may be included.
NOTE: *The User Guide can be found on your USB mass storage device.
NOTE: The appearance of some components may vary.
Power Supply Power Cord Quick Start
Guide
Pliers Scraper
Removable Print Pad Cartridges1
Cube Cube Glue
Casing and its contents
c
u
b
if
y.
co
m
USB Mass
Storage Device*
1.5 mm Allen
Wrench
Gap Gauge
Sandpaper
Casing
7
SETTING UP AND ACTIVATING YOUR CUBE
1. Select your language. Press the checkmark to conrm
your selection.
NOTE: The selected language will be indicated.
2. Enter a name for your printer. Scroll through the letters
by pressing the arrow symbols on each side of the
screen. Select the letters to spell out the name. Select
the checkmark to conrm your choice. Select SKIP
to bypass this step. You can name your printer at any
time by navigating to the System 1 screen and selecting
CUBE NAME.
NOTE: The abc button toggles between
lowercase letters, uppercase letters and
numerals.
3. Connect your printer to your network. Use the up or
down arrows to scroll to your network choice. Select
the desired network. Select SKIP to bypass this step.
You can connect to a wireless network at any time by
navigating to the Network screen and selecting WIFI.
NOTE: The printer can also connect to an ad
hoc network. Refer to the User Guide for more
information about connecting to an ad hoc
network.
Altri manuali per CUBE
9
Indice
Altri manuali 3D Systems Stampante 3D
3D Systems
3D Systems CubePro Manuale utente
3D Systems
3D Systems Viper Pro SLA iPro 8000 Manuale utente
3D Systems
3D Systems ProX 500 Manuale utente
3D Systems
3D Systems CUBE Manuale utente
3D Systems
3D Systems CubeX Istruzioni per il montaggio
3D Systems
3D Systems ProJet 660Pro Manuale utente
3D Systems
3D Systems CubePro Manuale utente
3D Systems
3D Systems Cubify CUBEX Duo Manuale elenco delle parti
3D Systems
3D Systems CubePro Manuale utente
3D Systems
3D Systems CubePro 3D Printer Manuale utente
3D Systems
3D Systems CubePro Manuale utente
3D Systems
3D Systems ProX SLS 6100 Manuale utente
3D Systems
3D Systems ProJet 7000 Manuale utente
3D Systems
3D Systems wematter Density Manuale utente
3D Systems
3D Systems CubePro Istruzioni per il montaggio
3D Systems
3D Systems ProJet SLA 6000 Manuale utente
3D Systems
3D Systems ProX DMP 100 Manuale utente
3D Systems
3D Systems projet mjp 2500 Manuale utente
3D Systems
3D Systems ZPRINTER 150 Manuale utente
3D Systems
3D Systems Allevi 3 Manuale utente
