3D Systems Cubify CUBEX Duo Istruzioni operative e di sicurezza

1

CUBEX

Print Jet

Replacement

Manual

2

Contents

Removing the damaged print jet ................................................................................3

Installing the new print jet...........................................................................................7

Levelling the print tips for CubeX Duo/Trio...............................................................10

Setting Print Tip offsets............................................................................................11

Fastening the print tip on a CubeX...........................................................................12

3

What you will need

Print jet assembly

2.5mm Hex driver

Pliers

4

Before beginning this process please remove all filament from the print jets

and check that your print pad is level. For instructions on how to do this

please refer to the CubeX users guide

Removing the damaged print jet

1. Turn off the CubeX printer and unplug it from the mains power.

2. Unplug the two white looms from the top of the damaged print jets sensor

board,

3. Label the Print Jet motor looms with the corresponding print jet number and

unplug them.

5

4. Remove the bolts holding the Feed Tube mount in place. The amount of bolt

will vary depending on the amount of print jets your CubeX has.

A CubeX will have the bolts circled in red.

A CubeX duo will have the two bolts circled in red and the bolt circled in green.

A CubeX trio has the bolts circled in red, green and blue.

5. You should now be able to move the Feed Tube mount from the top of the

print jets to expose the print jet mounting bolt.

6

6. Remove the mounting bolt. This can be very tight.

7. You should now be able to lift the print jet away from the Print Jet carriage

plate.

7

Installing the new print jet

1. Check your Print Jet is assembled and that the print tip moves freely when

pushed in and out of the drive. The Print tip moves freely for the levelling

process. Once the levelling process has been completed the Print tip will be

locked off.

If your Print Jet and print tip are not assembled together when you receive them, you

can assemble them by inserting the locating end of the Print tip into the Print Jet as

pictured below.

8

2. Place the Print Jet onto the Print Jet carriage plate as pictured, note the

locating standoff and corresponding hole present on the Print Jet

3. Ensure that the wires from the Print tip are orientated to travel straight up to

the Sensor board

4. Replace the M3 x 20 bolt into the hole as pictured and fasten. This must be

tight.

9

5. Re attach the Feed Tube mount.

6. Plug the motor looms back into their corresponding motors.

7. Plug in the Print Jet sensor board looms.

10

Levelling the print tips for CubeX Duo/Trio

If your CubeX only has a single print jet please see section ‘Fastening the print

tip on a CubeX’

1. Power on the CubeX printer

2. To clean the nozzles for levelling, put the CubeX printer into PJ-Control mode.

Heat all of the print jets EXCEPT for the new one to 230° and clean of any

plastic debris with pliers. Allow the Print Jets to cool down.

3. Put the CubeX printer into manual move mode.

4. Raise the print pad until it is approximately 5mm away from the print tips.

Altri manuali per Cubify CUBEX Duo

3

Questo manuale è adatto per i seguenti modelli

1

Indice

Altri manuali 3D Systems Stampante 3D

3D Systems

3D Systems ProJet 4500 Manuale utente

3D Systems

3D Systems iPro 8000 SLA Center Manuale utente

3D Systems

3D Systems ProX Manuale utente

3D Systems

3D Systems ProJet 1200 Manuale utente

3D Systems

3D Systems ProX 500 Manuale utente

3D Systems

3D Systems ProJet 1200 Manuale utente

3D Systems

3D Systems CubePro Manuale utente

3D Systems

3D Systems ProX DMP320 Manuale utente

3D Systems

3D Systems ZPrinter 350 Manuale utente

3D Systems

3D Systems CUBE Manuale dell'operatore

3D Systems

3D Systems ProJet 3500 Max Series Manuale utente

3D Systems

3D Systems CubeX Istruzioni per il montaggio

3D Systems

3D Systems FabPro 1000 Manuale

3D Systems

3D Systems Viper Pro SLA Manuale utente

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems ProX 950 Manuale utente

3D Systems

3D Systems ProX 950 Manuale utente

3D Systems

3D Systems PROJET 3500 Guida di riferimento

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems CubePro Manuale utente

3D Systems

3D Systems ProX SLS 6100 Manuale utente

3D Systems

3D Systems ProJet 5000 Manuale utente

3D Systems

3D Systems Duraform ProX PA Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente