3D Systems IPro 8000 SLA Center Manuale utente

Cover Page

User’s Manual

iPro™8000 SLA®Center

iPro™9000 SLA®Center

3D Sprint, 3DPrint, 3DManage, Lightyear, ProCure, Viper, iPro and Zephyr are trademarks of 3D Systems, Inc.

40-D043 –Rev C

www.3dsystems.com

Table of Contents

User’s Manual

Thank you for purchasing the iPro™ 8000 SLA ® Center. Before using this equipment, please read this guide carefully to

enjoy optimum performance and longer service life.

Introduction

What’s Inside?

iPro SLA System’s Features -RDM

Other Useful Documents

General Safety

Laser Safety

Chemical Safety

Environmental Conditions

Operations

Software Overview

View Port and View Object

Menu Bar

Tool Bar

Manual Operations

Scanner

History

Machine Window

Build Window

Mechanical Process

Troubleshooting

Customer Support

Service

Maintenance

System Block Diagram

Electronic Chassis Diagram

Legal Notices

Glossary

Specifications

Index

40-D043 Revision C 5-May-17

8000/9000

www.3dsystems.com

340-D043 Revision C 5-May-17

User’s Manual

8000/9000 I n t r o d u c t i o n

Introduction to the iPro™8000/9000 SLA®Center

Stereolithography - From stereo, for three-dimensional, and lithography, for printing,

stereolithography is literally three-dimensional printing. It is the term used to describe 3D Systems’

patented fabrication process that “prints”three-dimensional, solid objects by solidifying liquid plastic

using a computer-directed, ultraviolet (UV) laser beam to cure successive layers of photo-sensitive

polymer resin in an RDM (Resin Delivery Module).

The process “builds”three-dimensional solids from the bottom up, layer by layer. As each layer is

created and super-imposed on the layer underneath, a solid object in the shape of a three-

dimensional part is created, the origination of which typically occurs in a separate, computer-based

modeling application such as CAD, CAM, or CAE. Layer thickness can range (see the specifications

for details). A laser beam solidifies the layer of resin. The vertical elevator system lowers the newly

formed slice beneath the surface of the resin at a distance determined prior to part building. A

recoating system ensures consistent layer thickness. Layers build up until all the data for the model

is processed. Then the part is drained and removed from the iPro 8000/9000 SLA Center for post-

processing. The iPro 8000/9000 SLA Center consists of an assembly of numerous discrete sub-

systems that are integrated to perform 3-D stereolithographic model generation.

Developed in 1987 by the founder of 3D Systems, stereolithography was the first commercially

available layer-additive process to enable rapid fabrication of objects pulled directly from Computer-

Aided Design databases.

Our products and services are used by marketing professionals, purchasing departments,

engineering groups, research and development efforts, and design and testing teams all over the

world... to turn their CAD, CAM, CAE designs ---their IDEAS---into solid, tangible, plastic objects.

www.3dsystems.com

440-D043 Revision C 5-May-17

User’s Manual

8000/9000 I n t r o d u c t i o n

What’s the difference?

The numerous build configurations available from the two iPro systems featured in this manual offer

a broad range of options to produce high-definition plastic parts with unmatched quality and

accuracy. They use the same mechanical hardware, software, and methodology. The difference is

the size, and the options associated with size.

The iPro 9000 doubles the build zone of the iPro 8000 by allowing for 2 RDMs or an extra large

RDM. With the greater size, parts can be created in two separate RDMs simultaneously,

regardless of multiple part designs or resin materials. The iPro 9000 can also be used with a

combined RDM to produce parts up to 60 inches long.

The two iPro systems are designed to fit the variety of needs in production and the ever-changing

array of environments they run in.

www.3dsystems.com

540-D043 Revision C 5-May-17

User’s Manual

8000/9000 W h a t ’s i n s i d e ?

What’s Inside?

This manual includes the following topics:

Latest Features

“iPro SLA Center’s Features” describes the latest features incorporated into the iPro 8000/9000 SLA

Center, such as the resin delivery module (RDM), Intelligent Resin Container, Recoater, and

Scanning System. These features are improvements over previous SL models.

Many Other Useful Documents

In “Other Useful Documents” you’ll find a listing of many other documents that may be

helpful to you as you use the iPro 8000/9000 SLA Center, such as iPro 8000/9000 SLA Client Online

Help, the Facility Requirements Guide, and Material Safety Data Sheets.

Operations

“Operations” describes your new iPro 8000/9000 SLA Center. Pictures of the iPro 8000/9000

SLA Center’s components will help you understand the function of the various parts.

Software

“Software Overview” gives you a detailed overview of the software that operates your

iPro 8000/9000 SLA Center.

www.3dsystems.com

640-D043 Revision C 5-May-17

User’s Manual

8000/9000 W h a t ’s i n s i d e ?

Recoater System

“Recoater System” describes how to perform different operations with the resin delivery module

(RDM).

Safety

“General Safety”, “Laser Safety”, “Chemical Safety”, and “Environmental Conditions” describe

precautions that you should take when using your new iPro 8000/9000 SLA Center.

Service and Troubleshooting

In “Troubleshooting” and “Service”, you will find the troubleshooting guide and other basic

information concerning service and maintenance for your iPro 8000/9000 SLA Center.

Glossary

The “Glossary” defines terms that describe the iPro 8000/9000 SLA Center and its operations.

After the glossary, you will find the “Technical Specifications” for your iPro 8000/9000 SLA Center.

www.3dsystems.com

740-D043 Revision C 5-May-17

User’s Manual

8000/9000 F e a t u r e s

iPro 8000/9000 SLA Center’s Features

Resin Delivery Module (RDM)

The iPro 8000/9000 SLA Center allows for the faster material changes because of the innovative

mobile design of the RDM. Not only can you now change resin in less than ten minutes, you can

also swap the resin delivery module (RDM) easily, with no tools required . All components that come

into contact with resin in the RDM are moved with the module itself. You can remove the RDM easily

and quickly and replace it with another active RDM, without having to clean any wet resin surface.

This new RDM design significantly reduces the time to swap between build materials. In addition,

you can warm up an RDM offline, enabling you to swap one resin delivery module for another that is

ready to use. Gloves, however, may be required to detach the Zephyr ™recoater blade. This new

handling method ensures that all parts that come into contact with resin under normal operation are

a part of the active RDM.

The RDM is a vital system component. It is the mobile container

that stores the resin material and is rolled into the iPro™SLA®

Center to build parts.

The older generation SLA systems referred to this container as a

“Vat”because it was basically just a square metal tub. The RDM

is much more than just a container, it stores all the components

that contact the build material as well as using identification

electronics to communicate to the iPro SLA Center. This allows

the system to detect when the RDM is installed, the type of RDM

being used, and the material contained within the RDM.

www.3dsystems.com

840-D043 Revision C 5-May-17

User’s Manual

8000/9000 F e a t u r e s

Table 1, shown below, lists the required build envelopes that represent all RDM and platform

elevator configurations that the iPro 8000/9000 SLA Center supports. Each RDM and platform

elevator design minimizes the amount of resin that the iPro 8000/9000 SLA Center requires.

Table 1: RDM Configurations

Name Maximum Build Volume Fill Capacity

RDM 650M 650 x 350 x 300 mm (25.6 x 13.7 x 11.8 in) 148 liters (39.1 U.S. gal)

RDM 750SH 650 x 750 x 50 mm (25.6 x 29.5 x 1.97 in) 95 liters (25.1 U.S. gal)

RDM 750H 650 x 750 x 275 mm (25.6 x 29.5 x 10.8 in) 272 liters (71.86 U.S. gal)

RDM 750F 650 x 750 x 550 mm (25.6 x 29.5 x 21.65 in) 414 liters (109.3 U.S. gal)

RDM iPro 9000 XL 1500 x 750 x 550 mm (59 x 29.5 x 21.7 in) 935 liters (247 U.S. gal)

The iPro 9000 XL builds large, single-piece parts up to 60-inches long

with all of the performance attributes and accuracy that users have

come to expect from 3D Systems' high-definition Stereolithography

process. This system delivers extra-large parts with no seams for

aesthetic superiority, one-piece durability, resulting in reduced labor and

decreased cost. This RDM is only available for use in the iPro 9000

SLA Center.

www.3dsystems.com

940-D043 Revision C 5-May-17

User’s Manual

8000/9000

There are two operating modes for the RDM:

Stand-by Mode

In this mode, the RDM is offline and operates independently from the iPro 8000/9000 SLA Center,

permitting offline resin and module temperature stabilization when it is connected with line power

to the power umbilical. The resin can warm effectively in this mode, enabling the user to build a

part while warming resin for future use.

Build Mode

In this mode, the RDM is online and connects to the iPro 8000/9000 SLA Center for power and

I/O for full interoperability. The iPro 8000/9000 SLA Center monitors and controls the resin

temperature while connected with the active RDM. When the RDM is online, it can pump and

recirculate resin.

F e a t u r e s

Intelligent Resin Container

Each container in the iPro 8000/9000 SLA Center holds an

electronic storage device that has information about the resin

that is in the bottle and the RDM. This information enables the

iPro SLA Center to make sure that the user does not use the

wrong material, use material incorrectly, or use an empty or

expired container.

www.3dsystems.com

10 40-D043 Revision C 5-May-17

User’s Manual

8000/9000 F e a t u r e s

Single Resin Delivery Module

The iPro 8000/9000 SLA Center builds with one resin delivery module,

focusing on speed and accuracy, without compromising space requirements.

Dual Resin Delivery Module

The iPro 9000 SLA Center can also build parts in two separate build zones, Build Zone A and

Build Zone B. Each zone is independently capable of supporting its own active resin delivery

module and motion axis control, enabling controlled builds in both zones simultaneously, with

each build using different resins if desired.

Extra Large Resin Delivery Module

The iPro 9000 SLA Center can operate so that two build zones combine into

a single larger build zone to create larger parts that make up a single

contiguous envelope. The extra large resin delivery module accommodates a

build zone of 1500mm x 750mm x 550mm.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali 3D Systems Stampante 3D

3D Systems

3D Systems Cube 3rd Generation Manuale utente

3D Systems

3D Systems CubePro Manuale utente

3D Systems

3D Systems CubePro Istruzioni utente

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems CubePro Manuale

3D Systems

3D Systems ProJet 1200 Manuale utente

3D Systems

3D Systems Duraform ProX PA Manuale utente

3D Systems

3D Systems ProJet 2500 Manuale utente

3D Systems

3D Systems ProX DMP 100 Manuale utente

3D Systems

3D Systems CubePro Istruzioni per il montaggio

3D Systems

3D Systems CubePro Manuale utente

3D Systems

3D Systems CubeX Istruzioni per il montaggio

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems ProJet MJP 5600 Manuale utente

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems ProX DMP320 Manuale utente

3D Systems

3D Systems ProX 800 Manuale utente

3D Systems

3D Systems CubePro Manuale elenco delle parti

3D Systems

3D Systems ProJet MJP 3600 Manuale utente

3D Systems

3D Systems DMP Flex 350 Manuale utente

3D Systems

3D Systems PROJET 3500 Guida di riferimento

3D Systems

3D Systems ZPRINTER 150 Manuale utente

3D Systems

3D Systems CubeX Manuale utente

3D Systems

3D Systems ProX 500 Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente

3D Systems iPro 8000 SLA Center Manuale utente

Manuali Stampante 3D popolari di altre marche