3D Systems Cubify CUBEX Duo Manuale utente

CUBEX

Measuring

Stepper motor

chip voltages

Contents

What you will need ..................................................................................................... 3

Removing the Jet Wipe .............................................................................................. 4

Removing the Case and floor panel. .......................................................................... 4

Voltage Measurement Locations................................................................................ 6

Reading the Voltages................................................................................................. 7

Re attaching the floor panel and case........................................................................ 8

What you will need

Multimeter

3mm hex driver

Small Screwdriver

Before beginning this process please ensure that all cartridges have been

removed from the machine.

Removing the Jet Wipe

Run the bed to the bottom of the machine using manual move.

Lift Jet wipe out of the machine

Removing the Case and floor panel.

Using the 3mm hex driver remove the 8 case bolts (4 either side of the machine).

Unplug the CubeX screen.

Lift the case up off the CubeX.

Using the 3mm hex driver undo the 5 bolts holding the floor panel to the machine.

Lift the front of the floor panel and cable tie it to the bed arms. This will allow you

access to the Main Board PCB.

Voltage Measurement Locations

Depending which stepper motor chip voltage you want to read, you will need to

position your multimeter in different positions of the board. You will need to place a

small screwdriver with one end of the multimeter clipped onto it on the small screw

head labelled TP – and another end of the multimeter will need to be set to ground

on the board.

TP X will measure the voltage for the X axis.

TP Y will measure the voltage for the Y axis.

TP Z will measure the voltage for the Z axis.

TP E1, TP E2 and TP E3 will measure the voltage for print jets 1, 2 and 3.

TP Z

TP Y

TP X

Ground

Reading the Voltages

Plug the CubeX into mains power

Set the multimeter to read DC voltage.

Place the Red (positive) lead onto the desired TP screwhead.

TP E1

TP E2

TP E3

Hold the other end of the multimeter against the ground point.

The multimeter screen will give you your voltage reading.

TP X should read 1.3VDC

TP Y should read 1.6VDC

TP Z should read 1.3VDC

TP E1, E2 and E3 should read 1.1VDC

If your voltage is not correct use the small screwdriver to turn the screwhead in very

small increments measuring the voltage between each turn until it is correct.

Unplug your CubeX from mains power.

Re attaching the floor panel and case.

Cut the cable tie holding the floor panel in place and gently lower it down.

Using the 3mm hex driver re attach the 5 bolts that hold the floor panel.

Slide the case onto the CubeX and plug in the CubeX screen.

Using the 3mm Driver re attach the 8 case bolts.

You may now power up your CubeX.

Altri manuali per Cubify CUBEX Duo

Indice

Altri manuali 3D Systems Stampante 3D

3D Systems

3D Systems FabPro 1000 Manuale

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems ProJet 6000 Manuale utente

3D Systems

3D Systems ProX 950 Manuale utente

3D Systems

3D Systems Cube 2nd Generation Manuale utente

3D Systems

3D Systems Cubify CUBEX Duo Manuale utente

3D Systems

3D Systems wematter Density Manuale utente

3D Systems

3D Systems ProJet MJP 3600 Manuale utente

3D Systems

3D Systems Viper Pro SLA Manuale utente

3D Systems

3D Systems CubePro Istruzioni utente

3D Systems

3D Systems ProX 500 Manuale utente

3D Systems

3D Systems ProX 800 Manuale utente

3D Systems

3D Systems ProJet 4500 Manuale utente

3D Systems

3D Systems ProX SLS 6100 Manuale utente

3D Systems

3D Systems ProJet 4500 Manuale utente

3D Systems

3D Systems Viper Pro SLA iPro 8000 Manuale utente

3D Systems

3D Systems CUBE Manuale utente

3D Systems

3D Systems CubePro Istruzioni per il montaggio

3D Systems

3D Systems Cube 3rd Generation Manuale utente

3D Systems

3D Systems ProJet 4500 Manuale utente

3D Systems

3D Systems PROJET 3500 Guida di riferimento

3D Systems

3D Systems CubePro Manuale elenco delle parti

3D Systems

3D Systems ProJet 6000 Manuale utente

3D Systems

3D Systems wematter Atmosphere Manuale utente

Manuali Stampante 3D popolari di altre marche

Ultimaker

Ultimaker S5 Material Station Manuale utente

EcubMaker

EcubMaker TOYDIY Manuale utente

AnyCubic

AnyCubic Kossel Plus Manuale utente

ReDeTec

ReDeTec ProtoCycler Manuale utente

Kywoo3D

Kywoo3D Tycoon IDEX Manuale utente

CraftBot

CraftBot PLUS PRO Manuale utente

3DGence

3DGence INDUSTRY F340 Manuale utente

HP Jet Fusion 4200 Istruzioni operative

Rokit

Rokit AEP Series Manuale utente

AnkerMake

AnkerMake M5 Manuale utente

DIYElectronics

DIYElectronics PRUSA I3 Istruzioni per il montaggio

Ackuretta

Ackuretta FreeShape 120 Manuale utente

LONGER

LONGER LK5Pro Manuale utente

Stratasys

Stratasys J850 Manuale utente

MakerBot

MakerBot Replicator Manuale utente

Stratasys

Stratasys FDM Vantage Series Manuale utente

ZYYX

ZYYX Pro II Manuale utente

FLASHFORGE 3D PRINTER

FLASHFORGE 3D PRINTER Creator Guida utente