ABB MTAC-01 Manuale utente

ABB Drives

User’s Manual

Pulse Encoder Interface Module

MTAC-01

Pulse Encoder Interface Module

MTAC-01

User’s Manual

3AFE68591091 REV B

EFFECTIVE: 04.04.2006

Safety

Overview

This chapter states the general safety instructions that must be

followed when installing and operating the MTAC-01 Pulse

Encoder Interface module.

The material in this chapter must be studied before attempting any

work on, or with, the unit.

In addition to the safety instructions given below, read the

complete safety instructions of the specific drive you are working

on.

General safety instructions

WARNING! All electrical installation and maintenance work on the

drive should be carried out by qualified electricians.

The drive and adjoining equipment must be properly grounded.

Do not attempt any work on a powered drive. After switching off

the input power, always allow the intermediate circuit capacitors

5 minutes to discharge before working on the drive, the motor or

the motor cable. It is good practice to check (with a voltage

indicating instrument) that the drive is in fact discharged before

beginning work.

The motor cable terminals of the drive are at a dangerously high

voltage when input power is applied, regardless of motor

operation.

There can be dangerous voltages inside the drive from external

control circuits even when the drive input power is shut off.

Exercise appropriate care when working on the unit. Neglecting

these instructions can cause physical injury or death.

Safety

Table of contents

Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

General safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Table of contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Preparing for installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Installing the module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Start-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

01 OPERATING DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

50 ENCODER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

19 TIMER & COUNTER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Diagnostics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Faults/Alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Table of contents

Installation

Preparing for installation

MTAC-01 module

The MTAC-01 Pulse Encoder Interface module is an interface for

connecting a digital pulse encoder to an ACS350 drive. A pulse

encoder should be used if accurate speed or position (angle)

feedback from the motor shaft is required.

Module layout

Compatibility

The MTAC-01 module is compatible with all ACS350 drives. To

confirm compatibility with a particular pulse encoder, compare the

pulse encoder requirements to Specifications on page 25.

SCR

GND

Vin

Vout

Installation

Installing the module

Delivery check

The MTAC-01 module package contains:

• MTAC-01 module

• grounding stand-off

• panel port adapter

• this manual.

Mounting

WARNING! Follow the safety instructions given in this manual and

in the ACS350 User’s Manual [3AFE68462401 (English)].

To mount the MTAC-01 module:

1. If not already off, disconnect the input power from the drive.

After disconnecting the input power, wait for 5 five minutes

before you start working on the drive.

2. Remove the possible control panel or panel cover from the

drive.

3. Remove the grounding screw in the top left corner of the drive’s

control panel slot and install the grounding stand-off in its place.

4. Ensure that the panel port adapter is attached to either the

panel port of the drive or the mate part of the MTAC-01 module.

5. Gently and firmly install the MTAC-01 module to the drive’s

panel slot directly from the front.

Note: Signal and power connections to the drive are automatically

made through a 6-pin connector.

6. Ground the module by inserting the screw removed from the

drive in the top left corner of the MTAC-01 module. Tighten the

screw.

Indice

Altri manuali ABB Unità di controllo

ABB

ABB JSHD4 Manuale utente

ABB

ABB OMD100 Manuale utente

ABB

ABB FCAN-01 Manuale di installazione

ABB

ABB LEANtouch 6x36/30M-500 Series Manuale utente

ABB

ABB FCAN-01 Manuale utente

ABB

ABB Relion 670 series Istruzioni per l’uso

ABB

ABB RBIP-01 Manuale utente

ABB

ABB Relion REC670 Istruzioni per l’uso

ABB

ABB FDNA-01 Manuale di installazione

ABB

ABB FSCA-01 Manuale di installazione

ABB

ABB RMBA-01 Manuale utente

ABB

ABB Relion 630 Series Istruzioni per l’uso

ABB

ABB AC500 PLC Manuale utente

ABB

ABB Relion 630 Series Manuale utente

ABB

ABB TA571-SIM Manuale utente

ABB

ABB NPBA-01 Manuale di installazione

ABB

ABB 650 series Istruzioni per l’uso

ABB

ABB FSO-12 Manuale utente

ABB

ABB FSE-31 Manuale utente

ABB

ABB ACS880-1604LC Manuale utente

ABB

ABB jokab safety Smile Tina Series Manuale utente

ABB

ABB ACQ810 Manuale per l'uso e la cura

ABB

ABB WaveLINE 6731-21-500 Manuale utente

ABB

ABB RELION REC650 Guida rapida

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente