ABB RELION 650 SERIES Scheda tecnica

Relion® 650 SERIES

DNP, 650 series

Version 1.1 ANSI

Point list manual

Document ID: 1MRK 511 244-UUS

Issued: November 2019

Revision: A

Product version: 1.1

This document and parts thereof must not be reproduced or copied without written permission

from ABB, and the contents thereof must not be imparted to a third party, nor used for any

unauthorized purpose.

The software or hardware described in this document is furnished under a license and may be

used or disclosed only in accordance with the terms of such license.

Trademarks

ABB and Relion are registered trademarks of ABB Group. All other brand or product names

mentioned in this document may be trademarks or registered trademarks of their respective

holders.

Warranty

Please inquire about the terms of warranty from your nearest ABB representative.

ABB AB

Substation Automation Products

SE-721 59 Västerås

Sweden

Telephone: +46 (0) 21 32 50 00

Facsimile: +46 (0) 21 14 69 18

http://www.abb.com/substationautomation

Disclaimer

The data, examples and diagrams in this manual are included solely for the concept or product

description and are not to be deemed as a statement of guaranteed properties. All persons

responsible for applying the equipment addressed in this manual must satisfy themselves that

each intended application is suitable and acceptable, including that any applicable safety or other

operational requirements are complied with. In particular, any risks in applications where a system

failure and/or product failure would create a risk for harm to property or persons (including but

not limited to personal injuries or death) shall be the sole responsibility of the person or entity

applying the equipment, and those so responsible are hereby requested to ensure that all

measures are taken to exclude or mitigate such risks.

This document has been carefully checked by ABB but deviations cannot be completely ruled out.

In case any errors are detected, the reader is kindly requested to notify the manufacturer. Other

than under explicit contractual commitments, in no event shall ABB be responsible or liable for any

loss or damage resulting from the use of this manual or the application of the equipment.

Conformity

This product complies with the directive of the Council of the European Communities on the

approximation of the laws of the Member States relating to electromagnetic compatibility (EMC

Directive 2004/108/EC) and concerning electrical equipment for use within specified voltage

limits (Low-voltage directive 2006/95/EC). This conformity is the result of tests conducted by ABB

in accordance with the product standards EN 50263 and EN 60255-26 for the EMC directive, and

with the product standards EN 60255-1 and EN 60255-27 for the low voltage directive. The IED is

designed in accordance with the international standards of the IEC 60255 series.

Table of contents

Section 1 Introduction......................................................................................................... 3

1.1 This manual.......................................................................................................................................... 3

1.2 Intended audience...............................................................................................................................3

1.3 Product documentation.................................................................................................................... 4

1.3.1 Product documentation set............................................................................................................4

1.3.2 Document revision history..............................................................................................................5

1.3.3 Related documents...........................................................................................................................5

1.4 Symbols and conventions..................................................................................................................7

1.4.1 Safety indication symbols............................................................................................................... 7

1.4.2 Manual conventions..........................................................................................................................7

1.4.3 Functions included in 650 series IEDs.......................................................................................... 8

Section 2 DNP3 data mappings.........................................................................................15

2.1 Overview..............................................................................................................................................15

2.2 Point list for the 650 series IEDs.................................................................................................... 15

Section 3 DNP3 protocol implementation....................................................................... 37

3.1 DNP3 device profile...........................................................................................................................37

3.2 DNP3 implementation table........................................................................................................... 40

Section 4 Glossary.............................................................................................................. 45

Table of contents

DNP, 650 series 1

Point list manual

Section 1 Introduction

1.1 This manual

GUID-AB423A30-13C2-46AF-B7FE-A73BB425EB5F v12

The point list manual describes the outlook and properties of the data points specific to the IED.

The manual should be used in conjunction with the corresponding communication protocol

manual.

1.2 Intended audience

GUID-C9B8127F-5748-4BEA-9E4F-CC762FE28A3A v6

This manual addresses the communication system engineer or system integrator responsible for

pre-engineering and engineering for communication setup in a substation from an IED

perspective.

The system engineer or system integrator must have a basic knowledge of communication in

protection and control systems and thorough knowledge of the specific communication protocol.

1MRK 511 244-UUS A Section 1

Introduction

DNP, 650 series 3

Point list manual

1.3 Product documentation

1.3.1 Product documentation set GUID-3AA69EA6-F1D8-47C6-A8E6-562F29C67172 v9

Planning & purchase

Engineering

Installing

Commissioning

Operation

Maintenance

Decommissioning

deinstalling & disposal

Application manual

Operation manual

Installation manual

Service manual

Engineering manual

Commissioning manual

Communication protocol

manual

Technical manual

Planning & purchase

Engineering

Installing

Commissioning

Operation

Maintenance

Decommissioning

deinstalling & disposal

Planning & purchase

Engineering

Installing

Commissioning

Operation

Maintenance

Decommissioning

deinstalling & disposal

Application manualApplication manual

Operation manualOperation manual

Installation manualInstallation manual

Service manualService manual

Engineering manualEngineering manual

Commissioning manualCommissioning manual

Communication protocol

manual

Communication protocol

manual

Technical manualTechnical manual

en07000220.vsd

IEC07000220 V1 EN-US

Figure 1: The intended use of manuals in different lifecycles

The engineering manual contains instructions on how to engineer the IEDs using the different

tools in PCM600. The manual provides instructions on how to set up a PCM600 project and insert

IEDs to the project structure. The manual also recommends a sequence for engineering of

protection and control functions, LHMI functions as well as communication engineering for IEC

60870-5-103, IEC 61850 and DNP3.

The installation manual contains instructions on how to install the IED. The manual provides

procedures for mechanical and electrical installation. The chapters are organized in chronological

order in which the IED should be installed.

The commissioning manual contains instructions on how to commission the IED. The manual can

also be used by system engineers and maintenance personnel for assistance during the testing

phase. The manual provides procedures for checking of external circuitry and energizing the IED,

parameter setting and configuration as well as verifying settings by secondary injection. The

manual describes the process of testing an IED in a substation which is not in service. The

chapters are organized in chronological order in which the IED should be commissioned.

The operation manual contains instructions on how to operate the IED once it has been

commissioned. The manual provides instructions for monitoring, controlling and setting the IED.

Section 1 1MRK 511 244-UUS A

Introduction

4DNP, 650 series

Point list manual

Altri manuali per RELION 650 SERIES

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali ABB Unità di controllo

ABB

ABB ret650 Guida rapida

ABB

ABB RELION REC650 Guida rapida

ABB

ABB REF 542plus Manuale utente

ABB

ABB FAIO-01 Manuale utente

ABB

ABB BCU-02 Manuale utente

ABB

ABB FSCA-01 Manuale di installazione

ABB

ABB Relion 630 Series Manuale utente

ABB

ABB CMS-660 Manuale utente

ABB

ABB ACQ580-34 Manuale utente

ABB

ABB Arc Guard System TVOC-2 Manuale del prodotto

ABB

ABB COM600 series Manuale utente

ABB

ABB REF 542plus Manuale utente

ABB

ABB NPBA-01 Manuale di installazione

ABB

ABB 616016-T2 Manuale per l'uso e la cura

ABB

ABB FPNO-21 Manuale di installazione

ABB

ABB Relion 615 series Manuale di installazione e funzionamento

ABB

ABB M10 Series Manuale utente

ABB

ABB Relion REC670 Istruzioni per l’uso

ABB

ABB ACSM1 Series Manuale per l'uso e la cura

ABB

ABB MTAC-01 Manuale utente

ABB

ABB OMD800 Guida utente

ABB

ABB OPT-MF-005 Manuale utente

ABB

ABB ACS880 Series Manuale del proprietario

ABB

ABB Relion SAM600-IO Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente