ADDC BioDigitalPC SR-60 Manuale utente

SR-60

USER GUIDE

PLUG INTO THE FUTURE OF TECHNOLOGY

Revision History

Revision Notes

V2.5 Revision 2.5 was published in

November of 2017.

Table of Contents

Section 1 Receiving Your SR-60 5

Section 1.1 What's in the Box? 5

Section 2 SR-60 Preparaon 6

Section 2.1 Preparing For Your SR-60 6

Section 2.2 Installing Your SR-60 into a Rack 7

Section 2.3 Installing Your BioDigitalPC®s9

Section 2.4 SR-60 Power Supplies 11

Section 2.5 Networking Your SR-60 12

Section 2.6 Powering On Your SR-60 13

Section 3 SR-60 Overview 14

Section 3.1 SR-10 Modules 15

Section 3.2 Rear Panel 16

Section 3.3 Front Panel 17

Section 4 ROMWare Soware 18

Section 4.1 Login 18

Section 4.2 Main Screen Overview 18

Section 4.3 AC Power Monitoring 19

Section 4.4 DC Power Control & Monitoring 20

Section 4.5 SR-10 Switch Conguraon 21

Section 4.6 BioDigitalPC® Power Contol and

Monitoring

Section 4.7 SR-10 Switch Serial Interface 25

Appendix A Tesng Your SR-60 27

Appendix B A Successful SR-60 Component Test 28

Notes, Important Information & Warnings

This manual details installation of the chasis, the components inside of the chassis, and notable

features of the SR-60 server solution.

Installations will be supported by ADDC. Unless otherwise specied, all instructions provided in this

manual will assume that a user is a trained technician.

How to Read this Document

 You will see this icon throughout the manual intended to point out warnings, important information,

and briey explain any new terminology.

Equipment (Not Included)

• Laptop or Testing Network

• 5/32" Allen Key (Optional)

Equipment (Included)

• SR-60 Chassis

• SR-60 Top Cover [Comes Assembled]

• BioDigitalPC®Server Cards [Check

Invoice for Quantity]

• 4 AC/DC Power Supplies

• 12 10Gbps SFP+ Cables

• 4 AC Power Cords

• 2 Rack Slides

Section 1.1 - What's in the Box?

10Gbps SFP+ Cables

SR-60 Chassis

SR-60 Top Cover

Rack Slides

AC/DC Power Supplies

AC Power Cords

Section 1.0 - Recieving Your SR-60

When installing the SR-60 into a rack, the selected location should meet environmental standards as

described below.

Rack Space and Airflow Considerations

To allow for adequate airow, technicians should observe the following space and airow requirements

when deciding where to install a rack.

• Leave a minimum clearance of 36in (91.4cm) in front of the rack.

• Leave a minimum clearance of 20in (50.8cm) behind the rack.

Temperature Considerations

Your SR-60 is designed to operate at room temperature with its self-contained cooling.

Power Considerations

When properly congured and installed the SR-60 can draw up to 2kW depending on the number, load,

and version of the BioDigitalPC®s used.

 To prevent improper cooling of equipment, do not block the fans.

Section 2.1 - Preparing For Your SR-60

 If using the dual feed redundant power solution (See Section 2.6.2), each power source must be

capable of supporting a maximum draw of 2kW.

Section 2 - SR-60 Preparation

Section 2.2 - Installing Your SR-60 into a Rack

A. B.

The chassis package includes two rail assemblies in the rack mounting kit. Each assembly consists of

two sections: an inner xed chassis rail that secures directly to the server chassis and an outer xed

rack rail that secures directly to the rack itself.

Press the lever to

extend the outer rails.

 Stability hazard. The rack stabilizing mechanism must be in place, or the rack must be bolted to the

oor before you slide the unit out for servicing. Failure to stabilize the rack can cause the rack to tip

over and cause severe injury to the technicians and damage to the device.

This section provides information on installing the SR-60 chassis into a rack unit with the quick-release

rails provided.

Repeat step A to mount

all four corners.

Hang the hooks of the rails

into rack holes. Screw the

rails in if necessary.

Make sure the ball shuttle is

at the very front.

 Inner and outer chassis rails are shipped together, before continuing please seperate outer rail from

inner rail.

D. Align the inner rails into the extended outer rails and push the chassis to the rear of the rack.

Optional: Screw the

handles to the rack.

(Top Cover not shown)

Section 2.2 - Installing Your SR-60 into a Rack

Section 2.3 - Installing Your BioDigitalPC®s

BioDigitalPC®s are hot-pluggable, meaning technicians do not need to remove power to begin adding or

removing them.

Section 2.3.1 - Removing the SR-60 Top Cover:

In order to add or remove BioDigitalPC®s the SR-60 chassis can be pulled out of the rack, or the SR-60's

Top Cover needs to be removed temporarily.

 SR-60 system can be running while installing new server cards.

 Only trained technicians are authorized to work beneath the SR-60 System Cover and access any of

the components inside the system.

Section 2.3.2 - Installing a BioDigitalPC®

Step 3: Insert Card with

"Arnouse Digital Devices

Corp." facing upwards

and the connector of the

card is facing towards the

latch. When inserting the

card place between the

two horizontal metal bars,

ensuring the card is going

to be aligned properly.

Step 4: Once the card

is in between the two

horizonal bars, locate

the small locking tab and

push it in towards the

card. The card should

now be locked into place.

Fully inserted card

Step 1: Make

sure the latch is

perpendicular to

the system cover.

Step 2: Make sure

locking tab is unlocked.

small

locking tab

latch

Step 1: Find the

locking tab located

to the right of the

card slot.

Unlock the locking

tab.

Section 2.3.4 - Replacing the SR-60 Top Cover

Section 2.3.3 - Removing a BioDigitalPC®

Section 2.3 - Installing Your BioDigitalPC®s

Step 1: Insert Card with "Arnouse

Digital Devices Corp." facing

upwards and the connector of

the card is facing towards the

left. When inserting the card

place between the two horizontal

metal bars, insuring the card is

going to be aligned properly.

Step 2: Once the card is in

between the two horizonal bars,

locate the small locking tab and

push it in towards the card. The

card should now be locked into

place.

Once complete, a technician should

replace the SR-60 Top Cover.

Step 3: Reset the ejection bar to the original

position to make the card removal easier.

Step 2: Pull the

ejection bar forward

towards you, you

should feel the

card pop out of the

connector.

Indice

Manuali Server popolari di altre marche

HP AlphaServer ES47 Manuale utente

Dell

Dell PowerEdge R410 Manuale utente

PowerNAS

PowerNAS CMA Manuale utente

Supero

Supero FatTwin F617R3-FT Manuale utente

MSI

MSI P1-109N-L70 Manuale utente

Dell

Dell PowerEdge XE9640 Manuale

Dell

Dell PS4100 Istruzioni di montaggio

EtroVISION

EtroVISION EV3151 Manuale utente

NEC

NEC Express5800/T110j Manuale utente

HP ProLiant Gen9 Manuale utente

Compaq

Compaq ProLiant 3000 Manuale

Dell

Dell PowerEdge 3YPMN Manuale utente

iRobo

iRobo IPC2U Manuale utente

Nortel

Nortel 1000 Con?guration guide Manuale utente

Asus

Asus AP7500 Manuale operativo e di manutenzione

Avid Technology

Avid Technology AirSpeed 5000 Manuale utente

HP Integrity rx2600 Guida all'installazione

Milestone

Milestone Husky IVO 350T Manuale utente