Agilent Technologies MX3000P Manuale utente

MX3000P/MX3005P QPCR SYSTEM

INSTRUMENT QUALIFICATION β–ACTIN INSTALL PLATE INSTRUCTIONS

Plate Storage and Handling Instructions

The plate is shipped on dry ice. Store at –20°C upon receipt. Do not remove the foil wrapper until immediately

before performing the run.

Wear chemical-resistant powder-free gloves whenever handling the qualification plate. This will ensure that no

finger oils or other debris are transferred to the optical seal.

Preparing for the Qualification Test

Note The Mx3000P or Mx3005P instrument and MxPro software must be set up, according to the

instructions in the system Setup and User’s Guide, prior to running the Qualification Test.

The the Qualification Test requires filter gain settings of ×8 for FAM and ×1 for ROX as per factory

settings. To check and modify the filter gain settings, click Instrument > Filter Set Gain Settings.

Just before starting the Instrument Qualification Test run, thaw the plate at room temperature for

15–30 minutes, leaving the plate sealed in the foil wrapper while thawing.

After thawing, remove the foil wrapper and then mix the contents of the wells by completing the following

actions five times:

•Invert the plate. Use a sharp, swift, downward motion to move the liquid to the seal on top of each well.

Observe the liquid to verify that the liquid has moved from the bottoms to the tops of the tubes.

•Re-invert the plate, and use the same motion to return the liquid to the bottom of each well, again verifying

liquid movement before proceeding.

After completing five mixing cycles, collect the liquid at the bottom of the wells. Brief centrifugation of the

plate at 1000 rpm is highly recommended, in order to dislodge any bubbles and to collect the liquid.

If a plate centrifuge is not available, shake the liquid down to the bottom of the tubes (using the same motion

described above for mixing). Shake-down the plate until the majority of the liquid is at the bottom of the tube

and only minimal amounts of liquid are retained on the tube seal or sides. It is important to shake-down any

noticeable liquid on the tube seal (e.g. visible semi-circles or crescent shapes). Small amounts of liquid spray

retained on the tube sides should not affect the test results.

Prior to loading the plate, verify that no bubbles are present at the bottoms of the tubes, beneath the liquid.

While it is critical to remove any bubbles from the bottom of the tubes, small bubbles near the liquid meniscus

should not affect the test results.

Important Bubbles trapped at the bottom of the tubes will interfere with fluorescence readings, invalidating

the test.

Mx3000P or Mx3005P Instrument Qualification β–Actin Install Plate Instructions

600567-11, Revision C

Performing the Qualification Test Run

The first time the MxPro software is opened using an instrument-connected computer, the software provides a

prompt to run the Instrument Qualification Test. The test may also be initiated by selecting Qualification Test

from the Instrument menu. The software automatically loads the plate set-up and thermal profile for the

qualification run.

A validation protocol Wizard will provide instructions in a series of dialog boxes before, during, and after the

run. Since the Qualification Test is a fixed test, only the actions directed by the validation protocol Wizard can

be completed. Do not attempt to modify the Qualification Test experiment or to analyze data during the

Qualification Test run.

First, the Instrument Qualification Test-Start dialog opens. When the plate has been prepared for the run, click

Next to open the Instrument Qualification Test-Start Run dialog box. Enter any comments for the

qualification test. Verify that the Perfect Fit frame shipped with the instrument has been removed from the

thermal block area. Load the test plate in the thermal block, verifying the correct orientation

(well A1 in the top, left corner). Close the instrument door, and then select Start Run. The Mx3000P or

Mx3005P instrument will begin the Instrument Qualification Test run. If the Pre-Run Lamp Warm Up dialog

box appears, select Run Now.

Important While the Qualification Test experiment is running, do not open the instrument door or cancel

the run.

Data Analysis

When run is complete, the software will proceed to the Analysis-Text Report section and the Instrument

Qualification Test-Run Complete dialog box will appear. Select Analyze. The software will open the

Microsoft Excel Instrument Qualification Validation template and export the Text Report data into the template.

Notes If a

Server Busy error dialog box appears, click Retry until the data export succeeds.

If any Norton anti-virus dialog boxes appear, select Notify again in 1 Day, and close the dialog.

Qualification Validation

The Microsoft Excel Validation template will open to the FAM analysis tab. Verify that the Data Count cell

reports the result Good to ensure that all of the data has been correctly exported into Excel. Next, verify that the

Result cell reports a Pass result. A Pass result indicates that the instrument is working properly. In this case, it

is not necessary to E-mail the data to Technical Services.

If the test reports a Check result, it is important to call Technical Services and send the three data files,

including Customer Information.txt, into Technical Services by E-mail for troubleshooting guidance. Include the

name of your institution, a contact name, and the instrument serial number when sending the data to Technical

Services.

Instrument Qualification Completion

After checking the Microsoft Excel Validation template, go back into the MxPro software. For a test report

Check result only, the Instrument Qualification Test-E-mail Experiment dialog box will appear and present

the option to automatically E-mail the data or save the data to a disk to later E-mail the data to Technical

Services ([email protected]). Finally, the Instrument Qualification Test-Complete dialog box will appear,

indicating that the test is finished.

Technical Services

Telephone: To find worldwide support telephone

numbers visit www.genomics.agilent.com and click

Email: qpcr@agilent.com

Altri manuali per MX3000P

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Agilent Technologies Attrezzature da laboratorio

Agilent Technologies

Agilent Technologies 1100 Series Manuale utente

Agilent Technologies

Agilent Technologies TS-5400 Manuale utente

Agilent Technologies

Agilent Technologies ZORBAX RRHT Series Manuale utente

Agilent Technologies

Agilent Technologies 5110 ICP-OES Manuale utente

Agilent Technologies

Agilent Technologies QuickSwap G3185B Manuale

Agilent Technologies

Agilent Technologies 33120A Manuale utente

Agilent Technologies

Agilent Technologies 1260 Infinity Manuale utente

Agilent Technologies

Agilent Technologies 1290 Infinity Flexible Cube Manuale utente

Agilent Technologies

Agilent Technologies 7820A Manuale utente

Agilent Technologies

Agilent Technologies 1200 series Manuale utente

Agilent Technologies

Agilent Technologies 1260 Infinity II Manuale utente

Agilent Technologies

Agilent Technologies InfinityLab Poroshell 120 Manuale utente

Agilent Technologies

Agilent Technologies 6890N Istruzioni operative

Agilent Technologies

Agilent Technologies 11970 Series Manuale utente

Agilent Technologies

Agilent Technologies InfinityLab LC Series Manuale utente

Agilent Technologies

Agilent Technologies Triple Quadrupole LC/MS Manuale utente

Agilent Technologies

Agilent Technologies IDP3GBKIT Manuale utente

Agilent Technologies

Agilent Technologies 4100 Manuale utente

Agilent Technologies

Agilent Technologies Magnis NGS Prep System Manuale utente

Agilent Technologies

Agilent Technologies BenchCel Microplate Handler Manuale utente

Agilent Technologies

Agilent Technologies gc/ms series Manuale utente

Agilent Technologies

Agilent Technologies 6850 Series Istruzioni per l'uso e l'installazione

Agilent Technologies

Agilent Technologies Agilent 1260 Infinity Manuale utente

Agilent Technologies

Agilent Technologies E2960B Series Istruzioni per l'installazione

Manuali Attrezzature da laboratorio popolari di altre marche

Qiagen

Qiagen DML 3000 Manuale utente

Queensgate

Queensgate NANOSCAN OP400 Manuale di programmazione

Conviron

Conviron GEN1000-GE Manuale utente

Parr Instrument

Parr Instrument 4560 Manuale di istruzioni

IKA

IKA IC control Manuale utente

Integra

Integra DOSE IT Manuale utente

Endress+Hauser

Endress+Hauser Cleanfit CPA875 Manuale utente

NI PXI-5422 Manuale

Collomix

Collomix Aqix Manuale utente

SPEX SamplePrep

SPEX SamplePrep 6875 Freezer/Mill Series Manuale utente

Ocean Insight

Ocean Insight FLAME-NIR+ Manuale utente

Parker

Parker ALIGN-MG-NA Manuale utente

BD 644787 Manuale utente

DENTAURUM

DENTAURUM Compact Megaplus Manuale utente

Biuged Laboratory Instruments

Biuged Laboratory Instruments BGD 626 Manuale utente

VWR

VWR SAS Super IAQ Manuale utente

illumina

illumina MiSeqDx Manuale utente

Yamato

Yamato BM510 Manuale utente