Agilent Technologies 34136A Manuale utente

User’s Guide

Agilent Technologies 34136A High Voltage Probe

WARNING This high voltage probe is designed to prevent accidental shock to the operator when properly used.

This operating note must be read and understood prior to using the probe. Improper procedures or

incorrect analysis of the measurement situation can result in serious shock.

General Information

The Agilent Technologies 34136A High Voltage Probe is an accessory to be used with analog or digital

multimeters having an input resistance of 10 M Ω ( ±1 %) . The Agilent Technologies 34136A is a

1000:1 divider which extends a voltmeter’s measurement capability to 40 kV dc/ 28 kV rms ac.

Specifications

Other Characteristics

AC output derates with frequency to

-3db at 300 Hz. The graph at the right

shows typical AC accuracy.

Actual AC accuracy varies with the

amount of shunted input capacitance.

Maximum Input Voltage Temperature Coefficient

DC Voltage: 40kV

AC Voltage: (0 to 300 Hz) 28 kV

RMS

Less than 200ppm/ °C

Accuracy Division Ratio Accuracy

DC volts: ±2 % ( 1 kV to 20 kV)

±3 % ( 2 0 kV to 40 kV)

1000:1 ±1% when terminated in 10 MΩ

2000:1 ±6 % when terminated in 1 MΩ

Note: For the 34401A, 34405A, L4411A, 34410A/11A,

and 3458A multimeters, the ACV input impedance function

has a 1 MΩinput impedance.

Pollution Degree 2

Input Resistance Operating Temperature

1000 MΩ0°C to +50 ° C

Cable Length: Storage Temperature:

1 meter −20 ° C to +70 °C

Altitude: Humidity

Up to 4,600 meters (15,000 ft) Up to 80% relative humidity at +40

°C

Accuracy

AC Volts: 5% at 60 Hz

-3

Atten

(dB)

Frequency

DC 300 Hz

Safety Precautions

• This high voltage probe must only be used by personnel who are trained, experienced, or otherwise

qualified to recognize hazardous situations and who are trained in the safety precautions that are

necessary to avoid possible injury when using such a device.

• Do not work alone when working with high voltage circuits

• For your own safety, inspect the probes for cracks and frayed or broken leads before each use.

If defects are noted, DO NOT use the probe.

• Hands, shoes, floor and work bench must be dry. Avoid making measurements under humid,

damp or other environmental conditions that might effect the safety of the measurement situation.

• It is advisable to turn the high voltage source off before connecting or disconnecting the probe.

• The probe body should be kept clean and free of any conductive contamination. Refer to the section

on cleaning.

Operation

• Connect the plugs to the volts [Hi] and com [Lo] terminals of your voltmeter

• Select the desired voltage function and range; do not use autoranging

• Whenever possible, turn the high voltage source off before making any connections

• Connect the divider probe common lead (alligator clip) to a good earth ground or reliable chassis

ground

Warning • Do not attempt to take measurements from sources where the chassis or return lead is not grounded

• The ground lead is critical to the safe operation of the probe. Failure to make this connection when

making high voltage measurements may result in personal injury or damage to the probe or voltmeter.

This connection must always be made BEFORE the probe tip comes in contact with the high voltage

and must not be removed until the probe tip has been removed from the high voltage source.

• Do not connect the ground clip lead to the high voltage source for any reason.

• Before turning the high voltage on, make sure that no part of your body is in contact with the device

under test.

• Measure the voltage remembering that the voltage being measured is 1000 times greater than the

voltmeter reading.

• Turn the high voltage off.

• Disconnect the probe tip from the high voltage source BEFORE removing the ground clip lead.

Cleaning

• Clean only the exterior probe body and cables. Use a soft cotton cloth lightly moistened with a mild

solution of detergent and water. Do not allow any portion of the probe to be submerged at any time.

• Dry the probe thoroughly before attempting to make voltage measurements.

• Do not subject the probe to solvents or solvent fumes as these can cause deterioration of the probe

body and cables.

Manual Part Number

34136-92000

*34136-92000*

Edition 2, September 2011

Altri manuali Agilent Technologies Strumento di misura

Agilent Technologies

Agilent Technologies B1500A Manuale utente

Agilent Technologies

Agilent Technologies PSA Series Istruzioni operative

Agilent Technologies

Agilent Technologies E8364-60102 Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies 4285A Manuale utente

Agilent Technologies

Agilent Technologies 7820A Guida utente

Agilent Technologies

Agilent Technologies E5505A Manuale utente

Agilent Technologies

Agilent Technologies FieldFox N9913A Manuale utente

Agilent Technologies

Agilent Technologies 8564EC Manuale utente

Agilent Technologies

Agilent Technologies MXA Series Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies 16441A R-Box Manuale utente

Agilent Technologies

Agilent Technologies FieldFox N9923AN Manuale utente

Agilent Technologies

Agilent Technologies 4294A Manuale del proprietario

Agilent Technologies

Agilent Technologies B1500A Guida all'installazione

Agilent Technologies

Agilent Technologies ESA-E Series Manuale

Agilent Technologies

Agilent Technologies ESA-E E4402B Manuale utente

Agilent Technologies

Agilent Technologies DSOX4USBSQ USB 2.0 Manuale utente

Agilent Technologies

Agilent Technologies 16089E Guida rapida

Agilent Technologies

Agilent Technologies 8753ES Manuale utente

Agilent Technologies

Agilent Technologies Agilent 7890 Series Guida

Agilent Technologies

Agilent Technologies ESA-E E4407B Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies E4980A Manuale utente

Agilent Technologies

Agilent Technologies FieldFox N9923A Manuale utente

Agilent Technologies

Agilent Technologies 11980A Manuale operativo

Agilent Technologies

Agilent Technologies N9320A Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente