Agilent Technologies 85225F Manuale utente

Agilent Technologies

Agilent85225F

PerformanceModelingSystem

Installation and User’s Guide

Notices

No part of this manual may be reproduced

in any form or by any means (including

electronic storage and retrieval or transla-

tion into a foreign language) without prior

agreement and written consent from Agi-

lent Technologies, Inc. as governed by

United States and international copyright

laws.

Manual Part Number

85225-90023

Edition

First edition, April 2005

Printed in USA

AgilentTechnologies,Inc.

1400 Fountaingrove Parkway

Santa Rosa, CA 95403 USA

Warranty

The material contained in this docu-

ment is provided “as is,” and is sub-

jectto being changed, without notice,

in future editions. Further, to the max-

imum extent permitted by applicable

law, Agilent disclaims all warranties,

either express or implied, with regard

to this manual and any information

contained herein, including but not

limited to the implied warranties of

merchantability and fitness for a par-

ticular purpose. Agilent shall not be

liable for errors or for incidental or

consequentialdamagesinconnection

with the furnishing, use, or perfor-

mance of this document or of any

information contained herein. Should

Agilent and the user have a separate

written agreement with warranty

terms covering thematerial in this

document that conflict with these

terms, the warranty terms in the sep-

arate agreement shall control.

Technology Licenses

Thehardwareand/orsoftwaredescribedin

this document are furnished under a

license and may be used or copied only in

accordance with the terms of suchlicense.

Restricted Rights Legend

If software is for use in the performance of

a U.S. Government prime contract or sub-

contract, Software is delivered and

licensed as “Commercial computer soft-

ware” as defined in DFAR 252.227-7014

(June 1995), or as a “commercial item” as

defined in FAR 2.101(a) or as “Restricted

computer software” as defined in FAR

52.227-19 (June 1987) or any equivalent

agency regulation or contract clause. Use,

duplication or disclosureof Software is

subject to Agilent Technologies’ standard

commercial licenseterms, and non-DOD

Departments and Agencies of the U.S. Gov-

ernment will receive no greater than

Restricted Rights as defined in FAR

52.227-19(c)(1-2) (June 1987). U.S. Govern-

ment users will receive no greater than

Limited Rights as defined in FAR 52.227-14

(June 1987) or DFAR 252.227-7015 (b)(2)

(November1995), as applicable in any

technical data.

Acknowledgments

UNIX®is a registered trademark of the

OpenGroup.

Windows NT®is a U.S. registered trade-

mark of Microsoft Corporation.

Windows®and MS Windows are U.S. reg-

istered trademarks of Microsoft Corpora-

tion.

Installation and User’s Guide 3

Safety and Regulatory Information

Warnings, Cautions, and Notes

This installation and user’s guide utilizes the following safety notations.

Familiarize yourself with each notation and its meaning before operating

the Agilent 85225F performance modeling system.

WARNING A WARNING notice denotes a hazard. It calls attention to an operating

procedure, practice, or the like that, ifnot correctly performed or

adhered to, could result in personal injury or death. Do not proceed

beyond a WARNING notice until the indicated conditions are fully

understood and met.

CAUTION A CAUTION notice denotes a hazard. It calls attention to an operating

procedure, practice, or the like that, if not correctly performed or adhered

to, could result in damage to the product or loss of important data. Do not

proceed beyond a CAUTION notice until the indicated conditions are fully

understood and met.

NOTE A NOTE calls the user’s attention to an important point or special

information within the text. It provides additional information or

instructions.

4Installation and User’s Guide

Safety Symbols and Instrument Markings

Symbols and markings in documentation and on instruments alert you to

potential risks, provide information about conditions, and comply with

international regulations. Table A defines the safety symbols and Table B

on page 5 defines the instrument markings you may find in the

documentation or on an instrument.

Table A Safety Symbols

Symbols Definition

Warning: risk of electric shock.

Warning: hot surface.

Caution: refer to instrument documentation.

Laser radiation symbol: marked on products that have a laser

output.

Alternating current.

Both direct and alternating current.

Three-phase alternating current.

Earth (ground) terminal.

Protective earth (ground) terminal.

Frame or chassis terminal.

Terminal is at earth potential. Used for measurement and

control circuits designed to be operated with one terminal at

earthpotential.

Terminal for neutral conductor on permanently installed

equipment.

Terminal for line conductor on permanently installed

equipment.

Installation and User’s Guide 5

Operator Safety Requirements

The following general safety precautions must be observed during all

phases of operation of this system. Failure to comply with these

precautions or with specific warnings elsewhere in this manual violates

Standby (supply). Units with this symbol are not completely

disconnectedfromACmainswhenthisswitchisinthestandby

position. To completely disconnect the unit from AC mains,

either disconnect the power cord, or have a qualified/licensed

electrician install an external switch.

ON (supply). A switch with this symbol closes the instrument’s

power supplycircuit, connecting it to the mains supply.

OFF(supply).Aswitch withthissymbolopensthe instrument’s

power supplycircuit, disconnecting it from the mains supply.

Table B Instrument Markings

Marking Definition

The instruction documentation symbol appears when it is

necessary for the user to refer to the instruction in the

documentation.

The CE mark is a registered trademark of the European

Community.

This product complies with the WEEEDirective (2002/96/EC)

markingrequirements.Theaffixedlabelindicatesthatyoumust

not discard this electrical/electronic product indomestic

household waste. To return unwanted products, contact your

local Agilent Technologies office, or see www.agilent.com for

more information.

The CSA mark is a registered trademark of the

CSA-International.

The C-tick mark is a registered trademark of the Spectrum

Management Agency of Australia. This signifies compliance

with the Australian EMC Framework regulations under the

terms of the Radio Communications Act of 1992.

ISM1-A ThistextindicatesthattheinstrumentisanIndustrialScientific

and Medical Group 1 Class A product (CISPER 11, Clause 4).

ICES/NMB-001 This text indicates product compliance with the Canadian

Interference-Causing Equipment Standard (ICES-001).

Table A Safety Symbols (continued)

Symbols Definition

N10149

6Installation and User’s Guide

safety standards of design, manufacture, and intended use of the product.

Agilent Technologies, Inc. assumes no liability for the customer’s failure to

comply with these requirements.

For additional safety precautions, including precautions for making device

measurements in a floating ground configuration, see “To ensure your

safety while using the system" on page 76.

WARNING This is a Safety Class 1 Product (provided with a protective earthing

ground incorporated in the mains supply cord). The mains plug shall

be inserted only in a socket outlet provided with a protective earth

contact. Any interruption of the protective conductor inside or

outside of the product is likely to make the product dangerous.

Intentional interruption is prohibited.

WARNING If this product is not used asspecified, the protection provided by the

equipment could beimpaired. This product must be used only in a

normal condition (in which all means for protection are intact) only.

WARNING DO NOT OPERATE IN AN EXPLOSIVE ATMOSPHERE. Do not operate

the instrument in the presence of flammable gasesor flames.

WARNING DO NOT REMOVE THE INSTRUMENT COVER. Operating personnel

must not remove instrument covers. Component replacement and

internal adjustments must be made only by qualified service

personnel. Instruments that appear damaged or defective should be

made inoperative and secured against unintended operation until

they can be repaired by qualified service personnel.

WARNING Installing additional instruments may destabilize the rack cabinet.

WARNING Installing additional instruments into the cabinet electrical system

could produce excessive leakage current. If the protective earth

conductor is interrupted or faulted, the user risks serious injury or

death.

WARNING Prior to adding any additional instruments, review all wiring and

coolingcapabilitiestoverifyadequatedesignmarginsfornormaland

under single fault conditions.

Installation and User’s Guide 7

Mains power

Ground the system

Before applying power

CAUTION The mains cable shall be permanently connected to the premise circuit

breaker or connected using an agency approved twist-lock connector.

WARNING To minimize shock hazard, the rack cabinet must be connected to an

electrical protective earth ground. The power distribution unit (PDU)

must be connected to the AC power mains through a groundedpower

cable, with the ground wire firmly connected to an electrical ground

(safety ground) at the power outlet.

WARNING Any interruption of the protective (grounding) conductor or

disconnection of the protective earth terminal will cause a potential

shock hazard that could result in personal injury.

CAUTION Verify that the product is set to match the available line voltage, the

correct fuse is installed, and all safety precautions are taken. Before

applying power, note the product’s external markings described in

Table A, “Safety Symbols,” on page 4 and Table B, “Instrument

Markings,” on page 5.

CAUTION It is recommended that the premise wiringcontain an adequate circuit

breaker for system protection.

CAUTION To remove power from the cabinet, remove the mains supply from the

premise electrical supply.

CAUTION Before switching on this system, make sure that the supply voltage is

in the specified range.

8Installation and User’s Guide

Fuses and breakers

Before cleaning the system

Overcurrent protection

Statement of Compliance and Declaration of Conformity

This product has been designed and tested in accordance with accepted

industry standards, and has been supplied in a safe condition. The

documentation contains information and warnings that must be followed

by the user to ensure safe operation and to maintain the product in a safe

condition.

The Manufacturer’s Declaration of Conformity is available upon request.

Statement of CAN/CSA Compliance

This product has been designed and tested in accordance with

CAN/CSA- C22.2 No. 61010- 1 IEC.

CAUTION The front panel LINE switch disconnects themains circuit fromthe

mains supply.However, themainssupplytothepowerdistributionunit

remainsenergized.

WARNING For continued protection against fire hazard, use only fuses with the

required rated current, voltage, and specified type (normal blow,

time delay). Do not use repaired fuses or short-circuited fuse

holders. Replace only with an identical fuse.

There are two resettable thermal breakers located on the power

strips. These are in the “hot” and “neutral” lines.

WARNING To preventelectrical shock, disconnect thesystem from mains before

cleaning. Use a dry (or slightly water-dampened) cloth to clean

external case parts. Do not attempt to clean internally.

CAUTION If the power outlet strip breaker trips once, reset the breaker. If the

breaker trips twice, call a qualified/licensed electrician to service the

test system.

Installation and User’s Guide 9

Compliance with German Noise Requirements

This is to declare that this instrument is in conformance with the German

Regulation on Noise Declaration for Machines (Laermangabe nach der

Maschinenlaermrerordnung - 3.GSGV Deutschland).

Compliance with Canadian EMC Requirements

This ISM device complies with Canadian ICES- 001. Cet appareil ISM est

conformé à la norme NMB du Canada.

IEC/EN 61000-4-2 Electrostatic Discharge Immunity Test

This system passes using criterion C where operator intervention may be

necessary to restart the measurement software operations.

IEC/EN 61326 Electrostatic Discharge and Surge Immunity Test

This system complies with the Electrostatic Discharge and Surge Immunity

requirements in the IEC/EN 61326 standard using Performance Criterion

For Technical Assistance

To receive technical assistance, visit the online assistance web site, or call

the telephone number listed in Table 19 on page 107 appropriate to the

location of modeling system.

Acoustic Noise Emission/Geraeuschemission

LpA <70 dB LpA <70 dB

Operator position am Arbeitsplatz

Normal position normaler Betrieb

per ISO 7779 nach DIN 45635 t.19

10 Installation and User’s Guide

In This Guide...

This guide provides instruction on installing, verifying, and servicing the

system, as well as an introductory system overview and reference material.

This information is presented for use by the customer or an Agilent

Technologies field engineer.

1 Introducing the Agilent 85225F Performance Modeling System

This chapter provides a description of the system, its components,

integration, and characteristics.

2 Installing the System

Here you will find instruction on preparing the installation site, receiving

and inspecting the system (including a receiving checklist), installing the

worksurface, ensuring operator safety, connecting the bias networks, and

powering- on the system.

3 Verifying System Functionality

Turn here for instruction on choosing a level of system verification and

performing a post- installation functional verification test using a system

controller running IC- CAP software.

4 Servicing the System

This chapter includes instruction on troubleshooting the system, removing

and replacing system components, ordering replacement parts, and

acquiring additional assistance in solving measurement problems.

A Enhancing Measurement Accuracy

See this appendix for instruction on cleaning the system connections,

performing a system measurement calibration, and suggested intervals for

periodic component calibration.

B DC Subsystem Functional Verification Tests

Turn here to find Agilent 4156C precision semiconductor parameter

analyzer and Agilent E5260A/70B high speed/precision parameteric

measurement mainframe functional verification tests that do not require

the IC- CAP software.

C RF Subsystem Functional Verification Tests

This appendix includes an Agilent E8364B PNA Series vector network

analyzer functional verification test that does not require the IC- CAP

software.

Indice

Altri manuali Agilent Technologies Strumento di misura

Agilent Technologies

Agilent Technologies 4395A Manuale utente

Agilent Technologies

Agilent Technologies Acqiris DC110 Manuale utente

Agilent Technologies

Agilent Technologies ESA E4401B Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies 4500 Series Manuale utente

Agilent Technologies

Agilent Technologies N1996A-503 Manuale di servizio

Agilent Technologies

Agilent Technologies E4418B Manuale utente

Agilent Technologies

Agilent Technologies E7401A Manuale utente

Agilent Technologies

Agilent Technologies 4288A Manuale del proprietario

Agilent Technologies

Agilent Technologies 8614 B Series Manuale utente

Agilent Technologies

Agilent Technologies Agilent 4396B Istruzioni operative

Agilent Technologies

Agilent Technologies VS Series Guida di riferimento

Agilent Technologies

Agilent Technologies OmniBER OTN Series Manuale utente

Agilent Technologies

Agilent Technologies E8361C Guida rapida

Agilent Technologies

Agilent Technologies HP 16500B Manuale di servizio

Agilent Technologies

Agilent Technologies 4352B Manuale utente

Agilent Technologies

Agilent Technologies B1500A Guida all'installazione

Agilent Technologies

Agilent Technologies L4532A Series Manuale utente

Agilent Technologies

Agilent Technologies EPM-P Series Manuale per l'uso e la cura

Agilent Technologies

Agilent Technologies ADM1000 Manuale utente

Agilent Technologies

Agilent Technologies PSA Series Manuale utente

Agilent Technologies

Agilent Technologies NFA Series Manuale utente

Agilent Technologies

Agilent Technologies 1670G Series Manuale utente

Agilent Technologies

Agilent Technologies ENA Series Manuale utente

Agilent Technologies

Agilent Technologies E8363A Manuale di installazione e funzionamento

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente