Agilent Technologies G6600 Guida

Purpose

The Brass Burner has two ceramic combustion tubes which require periodic

replacement: an inner and an outer tube.

Scope

This procedure applies to ceramic tube replacement in the Agilent Instruments

ABI 00003 Brass Burner.

Tools

•2 - 1/16” Open End Wrenches

•2 - 3/8” Open End Wrenches

•2 - 7/16” Open End Wrenches

Procedure

1. Turn off the Interface Controller and let the system cool down under

vacuum.

The Burner is extremely hot when running. Do not touch the burner until it has

cooled down.

2. Turn off the vacuum pump.

3. Remove the hydrogen line by disconnecting the Hydrogen Inlet Fitting at

the top of the Burner. Use a second wrench to hold the Adapter Tee to

avoid excess torque on the ceramic tubes.

4. Disconnect the black PFA transfer line from the Tee of the Burner

Interface.

5. Unscrew the Tee fitting and carefully pull the inner Tube/Tee assembly

from the Burner. If the existing Tube is broken then all fragments must

be removed from the burner.

Note

Ceramic Probe Replacement

Instructions

Accessory G6600-60034

6. Remove the ferrule attached to the top of the 1/8” ceramic tube.

7. Disconnect the Heater Cable from the heating element leads.

The heating element leads are very fragile. Do not bend them excessively or they

will be damaged.

8. Disconnect the thermocouple leads from the Interface Controller.

9. Remove the four horizontal socket head cap screws holding the Burner

Case.

10. Carefully lift the Burner Case up off of the base and set it aside.

11. Remove the white insulating disk and the fiber insulating toroid from the

Burner base.

12. Remove the 1/8” ceramic tube by loosening the nut in the Burner base.

Discard the used ceramic tube and ferrule. Remove any debris from the

inside of the connection.

Screw extractors may be useful in removing old ferrules from Burner fittings.

Note

13. Insert the new 1/8” ceramic tube into the fitting with a new Vespel

ferrule. Slide the nut over the tube and tighten it until finger tight. Lift

the ceramic tube up 1 to 2 mm so that it will not be crushed by the

compression fitting. Tighten the nut snugly with the 7/16” wrench. This

connection must be fairly tight to ensure that the nut does not loosen

under heat stress, but excessive tightening can crack the ceramic tube.

14. Reinstall the fiber insulating toroid and the white insulating disk.

Carefully slide the Burner Cover over the large ceramic tube. It is often

useful to sight down the upper fitting to ensure that the ceramic tube is

properly aligned and will not break.

Failure to install the insulating disk may lead to leaks in the Burner.

15. Reinstall the four screws at the base of the Burner.

16. Unscrew the Hydrogen Inlet fitting from the Tee, and remove the 1/16"

tube and ferrule.

Note

17. Install a new 1/16" Vespel ferrule at the top of the Tee. Slide in a new

inner ceramic tube until approximately 1/8" (2 mm) extends out of the

top of the ferrule Retighten the Hydrogen Inlet fitting snugly. Do not

overtighten the fitting.

18. Replace the Tube and Tee assembly into the Burner, tightening finger

tight.

19. Check the flow of air and hydrogen following the Detector manual

instructions.

20. Reconnect the Heater Cable, Thermocouple, and all the tubing. Pressure

test the system following the instructions in the Detector manual. The

pressure may change slightly due to variation in tube dimensions.

21. Turn on the Interface Controller and allow the Burner temperature to

stabilize. Gently tighten all the fittings once the Burner temperature is

stable.

Agilent Technologies, Inc.

2850 Centerville Road

Wilmington, DE 19808-1610

Printed in the USA Feb 2007

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Agilent Technologies Strumento di misura

Agilent Technologies

Agilent Technologies N5230A Manuale utente

Agilent Technologies

Agilent Technologies 8753ES Manuale utente

Agilent Technologies

Agilent Technologies PSA Series Manuale utente

Agilent Technologies

Agilent Technologies N5225-60114 Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies 4156b Manuale utente

Agilent Technologies

Agilent Technologies 8590 Series Manuale utente

Agilent Technologies

Agilent Technologies E4418B Manuale utente

Agilent Technologies

Agilent Technologies UXA N9040B Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies All Manuale

Agilent Technologies

Agilent Technologies 4263B Manuale utente

Agilent Technologies

Agilent Technologies 89604 Manuale utente

Agilent Technologies

Agilent Technologies Agilent 4396B Manuale utente

Agilent Technologies

Agilent Technologies E5070B ENA Series Manuale utente

Agilent Technologies

Agilent Technologies FRG-700 Manuale utente

Agilent Technologies

Agilent Technologies E8362A Manuale utente

Agilent Technologies

Agilent Technologies Seahorse XFe Manuale utente

Agilent Technologies

Agilent Technologies 16718A Guida di riferimento

Agilent Technologies

Agilent Technologies 4349B Manuale utente

Agilent Technologies

Agilent Technologies 1664A Manuale utente

Agilent Technologies

Agilent Technologies PNA Series Manuale utente

Agilent Technologies

Agilent Technologies 8510C Manuale utente

Agilent Technologies

Agilent Technologies HP 8566B Manuale del proprietario

Agilent Technologies

Agilent Technologies E5900B Manuale utente

Agilent Technologies

Agilent Technologies E8362 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente