Agilent Technologies ICP-MS Series Istruzioni operative

Agilent ICP-MS

Interactive Troubleshooting tool for

Plasma ignition problem

Next >

Rev. B

2017, January, 20

Preconditions

•7900, 7800, 7700, 8800, or 8900 ICP-MS is used.

•Sample introduction type is “PeriPump”. If you are using a special configuration such as

LC/GC integration or ISIS, setup the instrument with standard configuration.

•You have the “Hardware Maintenance Manual”for your instrument. Some details of the

operations are not in this tool. You should refer to the manual.

<Previous Next >

Legends

Notes or tips that help troubleshoot.

You need to refer to another document for detail of the steps.

Good example of situation.

Bad example of situation.

Did the ion lens test pass? ←Questions are displayed in blue you need to click

buttons such as or

Based on your answer the tool will navigate you to next step.

Note

Reference

Good

Bad

<Previous Next >

Yes No

1.1.1 Check Water flow and Gas flow errors

(1) Select MassHunter Instrument Control Window → Main menu → “View” → “Instrument

Status” to display “Instrument Status” Pane

If Main menu is not displayed, press F10 key.

(2) Click the dropdown below and check the error number for errors that are generated at the

date/time of the attempt to ignite plasma.

(3) Are error numbers 1440, 1445, or 1446 included in the latest errors?

Note

<Previous Yes No

1.2.1 Check water and argon gas

(1) If error 1440 has been generated, check if cooling water valve is open and chiller or heat

exchanger is working correctly.

(2) If error 1445 or 1446 have been generated, check if argon gas valve is open and remaining

amount is enough.

(3) Did this solve the problem？

Yes No

1.3.1 Check timing when Plasma goes out

(1) When did Plasma go out?

Not ignite at all

Several seconds after ignition

One to several minutes after ignition

When "Plasma Correction“ is going on

20 minutes or later after ignition

2.1.1 Check condition of argon gas line condition

(1) Are there any situations below?

-Ar cylinder has been replaced recently

-Was there any work on Ar line recently?

-Is the instrument used after a long time ( > 1 month).

Yes No

2.2.1 Check condition of argon gas line

(1) Purge Ar line.

(2) Do leak check on Ar line.

(3) Check specification of Ar gas to have ≧99.99% purity (In case cylinder has been replaced).

(4) Try alternative source of Ar gas (In case cylinder has been replaced and any alternatives

are available)

(5) Does this fix the problem?

Yes No

2.3.1 Isolate the torch and try to ignite

(1) Block end of the torch with plastic film and try to ignite.

(2) Can it ignite?

Yes No

2.4.1 Check torch box

(1) Open the torch box and observe to check if there are situations below, following

instruction from the next page.

- Damaged torch

- Damaged bonnet

- Damaged shield plate

- Damaged shield contact

-Non Agilent torch

-Dirty torch stand

-Wrongly assembled torch

<Previous Next >

Questo manuale è adatto per i seguenti modelli

5

Indice

Altri manuali Agilent Technologies Strumento di misura

Agilent Technologies

Agilent Technologies Cary 60 Manuale utente

Agilent Technologies

Agilent Technologies U1701A Manuale utente

Agilent Technologies

Agilent Technologies E5070A ENA Series Manuale utente

Agilent Technologies

Agilent Technologies E4402/7B Manuale

Agilent Technologies

Agilent Technologies E5052A Manuale utente

Agilent Technologies

Agilent Technologies X Series Manuale utente

Agilent Technologies

Agilent Technologies ESA-E Series Manuale utente

Agilent Technologies

Agilent Technologies ENA Series Manuale utente

Agilent Technologies

Agilent Technologies BioTek Epoch 2 Manuale utente

Agilent Technologies

Agilent Technologies N1911A Manuale utente

Agilent Technologies

Agilent Technologies N9030A Manuale utente

Agilent Technologies

Agilent Technologies 4263B Manuale utente

Agilent Technologies

Agilent Technologies 55B AA Manuale utente

Agilent Technologies

Agilent Technologies N1913a Manuale utente

Agilent Technologies

Agilent Technologies ESA-E Series Manuale utente

Agilent Technologies

Agilent Technologies J2300D Manuale elenco delle parti

Agilent Technologies

Agilent Technologies PNA Series Manuale utente

Agilent Technologies

Agilent Technologies 3200 Series Manuale utente

Agilent Technologies

Agilent Technologies 8504B Manuale utente

Agilent Technologies

Agilent Technologies E4416A Manuale utente

Agilent Technologies

Agilent Technologies OmniBER OTN J7232A Manuale di istruzioni

Agilent Technologies

Agilent Technologies UXA N9040B Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies E5406A-Pro Series Manuale utente

Agilent Technologies

Agilent Technologies N9320B Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente