Agilent Technologies 8360B Manuale utente

Agilent Technologies

8360 B-Series Swept Signal Generator

8360 L-Series Swept CW Generator

Troubleshooting Guide

Part No. 08360-90124

Printed in USA

October 2000

Supersedes May 2000

Serial Number Preﬁxes:

This manual applies to any instrument with the following model

number and serial number preﬁx combinations. You may have to

modify this manual so that it applies directly to your instrument

version. Refer to the “Instrument History” chapter.

Agilent Technologies 83620B/22B/23B/24B/30B

3844A and Below

Agilent Technologies 83640B/50B

4040A and Below

Agilent Technologies 83623L/30L

3844A and Below

Agilent Technologies 83640L/50L

4040A and Below

title.f5s Page i Tuesday, July 10, 2001 12:58 PM

Notice

The information contained in this document is subject to

change without notice.

Agilent Technologies makes no warranty of any kind

with regard to this material, including but not limited to,

the implied warranties of merchantability and tness

for a particular purpose. Agilent Technologies shall not

be liable for errors contained herein or for incidental or

consequential damages in connection with the furnishing,

performance, or use of this material.

Restricted Rights Legend

Use, duplication, or disclosure by the U.S. Government

is subject to restrictions as set forth in subparagraph (c)

(1) (ii) of the Rights of Technical Data and Computer

Software clause at DFARS 252.227-7013 for DOD

agencies, and subparagraphs (c) (1) and (c) (2) of the

Commercial Computer Software Restricted Rights clause

at FAR 52.227-19 for other agencies.

Certication

Agilent Technologies certies that this product met its

published specications at the time of shipment from the

factory. Agilent Technologies further certies that its

calibration measurements are traceable to the United

States National Institute of Standards and Technology,to

the extent allowed by the Institute's calibration facility,

and to the calibration facilities of other International

Standards Organization members.

Warranty

This Agilent Technologies instrument product is

warranted against defects in material and workmanship

for a period of one year from date of shipment. During

the warranty period, Agilent Technologies will, at its

option, either repair or replace products which prove to

be defective.

For warranty service or repair, this product must be

returned to a service facility designated by Agilent

Technologies. Buyer shall prepay shipping charges to

and Agilent Technologies shall pay shipping charges to

return the product to Buyer. However, Buyer shall pay all

shipping charges, duties, and taxes for products returned

to Agilent Technologies from another country.

Agilent Technologies warrants that its software and

rmware designated by Agilent Technologies for use with

an instrument will execute its programming instructions

when properly installed on that instrument. Agilent

Technologies does not warrant that the operation

of the instrument, or software, or rmware will be

uninterrupted or error-free.

Limitation of Warranty

The foregoing warranty shall not apply to defects

resulting from improper or inadequate maintenance

by Buyer, Buyer-supplied software or interfacing,

unauthorized modication or misuse, operation outside

of the environmental specications for the product, or

improper site preparation or maintenance.

NO OTHER WARRANTY IS EXPRESSED OR IMPLIED.

AGILENT TECHNOLOGIES SPECIFICALLY DISCLAIMS

THE IMPLIED WARRANTIES OF MERCHANTABILITY

AND FITNESS FOR A PARTICULAR PURPOSE.

Exclusive Remedies

THE REMEDIES PROVIDED HEREIN ARE BUYER'S

SOLE AND EXCLUSIVE REMEDIES. AGILENT

TECHNOLOGIES SHALL NOT BE LIABLE FOR ANY

DIRECT, INDIRECT, SPECIAL, INCIDENTAL, OR

CONSEQUENTIAL DAMAGES, WHETHER BASED ON

CONTRACT, TORT, OR ANY OTHER LEGAL THEORY.

Assistance

Product maintenance agreements and other customer

assistance agreements are available for Agilent

Technologies products.For any assistance, contact your

nearest Agilent Technologies Sales and Service Oce.



translation without prior written permission is prohibited,

except as allowed under the copyright laws.

1400 Fountaingrove Parkway, Santa Rosa CA, 95403-1799,

USA

Safety Notes

The following safety notes are used throughout this

manual. Familiarize yourself with each of the notes and

its meaning before operating this instrument.

WARNING

Warning denotes a hazard. It calls attention to a

procedure which, if not correctly performed or

adhered to, could result in injury or loss of life.Do

not

proceed beyond a warning note until the indicated

conditions are fully understood and met.

CAUTION

Caution denotes a hazard. It calls attention to a

procedure that, if not correctly performed or adhered

to, would result in damage to or destruction of the

instrument. Do

not

proceed beyond a caution sign until

the indicated conditions are fully understood and met.

General Safety Considerations

WARNING

These servicing instructions are for use by qualied

personnel only.To avoid electrical shock, do not

perform any servicing unless you are qualied to do

so.

The opening of covers or removal of parts is likely

to expose dangerous voltages. Disconnect the

instrument from all voltage sources while it is

being opened.

The detachable power cord is the instrument

disconnecting device. It disconnects the mains

circuits from the mains supply before other parts

of the instrument. The front panel switch is only a

standby switch and is not a LINE switch.

The power cord is connected to internal capacitors

that may remain live for 5 seconds after

disconnecting the plug from its power supply.

This is a Safety Class I product (provided with a

protective earthing ground incorporated in the

power cord). The mains plug shall only be inserted

in a socket outlet provided with a protective

earth contact. Any interruption of the protective

conductor, inside or outside the instrument,

is likely to make the instrument dangerous.

Intentional interruption is prohibited.

For continued protection against re hazard

replace line fuse only with same type and rating

(F 5 A/250 V). The use of other fuses or material is

prohibited.

CAUTION

Always use the three-prong ac power cord supplied

with this instrument. Failure to ensure adequate earth

grounding by not using this cord may cause instrument

damage.

Before switching on this product, make sure that the

line voltage selector switch is set to the voltage of the

power supply and the correct fuse is installed. Assure

the supply voltage is in the specied range.

Manual Conventions

Front-Panel Key

This represents a key physically located

on the instrument.

NNNNNNNNNNNNNNNNNNNNNNN

Softkey

This indicates a \softkey," a key whose

label is determined by the rmware of

the instrument.

Screen Text

This indicates text displayed on the

instrument's screen.

vii

Instruments Covered By This Manual

This manual applies to instruments having a serial

number prex listed on the title page (behind the

\Documentation Map" tab). Some changes may have to

be made to this manual so that it applies directly to each

instrument; refer to Chapter 2, \Instrument History", to

see what changes may apply to your instrument.

A serial number label (see the gure) is attached to the

instrument's rear panel. A prex (four digits followed

by a letter), and a sux (ve digits unique to each

instrument), comprise the instrument serial number.

Typical Serial Number Label

viii

Troubleshooting

How to Use This Chapter

Menus

If you are not familiar with the menus in this instrument,

the

Agilent Technologies 8360 B-Series Swept Signal

Generator/L-Series Swept CW Generator Service Guide

contain fold-out menu maps which are located behind

the \Menu Maps" tab. Use the map for reference as you

troubleshoot.

Some menus have more than one page of softkeys

. Select

the

NNNNNNNNNNNNNN

softkey to see the next page of softkeys.

NNNNNNNNNNNNNN

not

included in the keystrokes given in this chapter.

Where to Begin Troubleshooting

Caution

Follow all troubleshooting procedures in the order given.

Done out of order, these procedures can miss critical

checks.You can waste time, and possibly replace the

wrong assembly.

Begin with \Instrument-Level Troubleshooting". This

section directs you to the appropriate troubleshooting

module.

Agilent 8360 Troubleshooting Introduction 1-1

Troubleshooting Modules

These modules pictorially guide you through the required

measurement steps (see the following example). Each

module covers one or more assemblies, and isolates a

problem to the assembly level.

Special Cases

This section covers problems not isolated in the

troubleshooting modules. \Special Cases" also contains an

instrument block diagram.

Troubleshooting Foldout

The troubleshooting foldout, referenced in the

troubleshooting modules, is located just prior to the

\Special Cases" tab.

1-2 Troubleshooting Introduction Agilent 8360

Altri manuali per 8360B

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Agilent Technologies Generatore portatile

Agilent Technologies

Agilent Technologies E8257C Manuale utente

Agilent Technologies

Agilent Technologies ESG-D Series Guida alla configurazione

Agilent Technologies

Agilent Technologies E4438C Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies HP 83711A Manuale utente

Agilent Technologies

Agilent Technologies ESG-D Series Guida rapida

Agilent Technologies

Agilent Technologies 8640b Manuale utente

Agilent Technologies

Agilent Technologies 85901A Manuale operativo

Agilent Technologies

Agilent Technologies N5161A Manuale utente

Agilent Technologies

Agilent Technologies V2920A Manuale utente

Agilent Technologies

Agilent Technologies E4438C Manuale utente

Agilent Technologies

Agilent Technologies E8267C Istruzioni operative

Agilent Technologies

Agilent Technologies E8663B Manuale utente

Agilent Technologies

Agilent Technologies E4400B Manuale utente

Agilent Technologies

Agilent Technologies N4000A Manuale di servizio

Agilent Technologies

Agilent Technologies 8360B Manuale utente

Agilent Technologies

Agilent Technologies E4428C Manuale utente

Agilent Technologies

Agilent Technologies 81141A Series Manuale utente

Agilent Technologies

Agilent Technologies E4423B Guida rapida

Agilent Technologies

Agilent Technologies ESG series Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies Agilent 33500 Series Manuale utente

Agilent Technologies

Agilent Technologies E4438CK-601 Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies E8267C Manuale utente

Agilent Technologies

Agilent Technologies E4430B Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies 33210A Manuale utente

Manuali Generatore portatile popolari di altre marche

Kohler

Kohler 20EORZ Manuale di istruzioni

Powerhorse

Powerhorse 83171 Manuale utente

HURST

HURST ML-630-SI Manuale utente

ETQ

ETQ TG4000 Manuale utente

Briggs & Stratton

Briggs & Stratton 40265 Guida all'installazione

ConMed

ConMed 7550 Manuale utente

Owon

Owon Waveform Generator Manuale utente

evertz

evertz 7700 Series Manuale utente

Power Stroke

Power Stroke PS906025 Manuale utente

Firefly

Firefly Cygnus CYG2400/460/24 Manuale utente

Draper

Draper PG950S Aggiornamento firmware

PowerBoss

PowerBoss PowerBoss Manuale utente

SDMO

SDMO SH 4000 Manuale utente

EINHELL

EINHELL STE 5500 Manuale utente

Wanco

Wanco WI3000P Manuale utente

Full Boar

Full Boar FBT-3300 Manuale utente

Dwyer Instruments

Dwyer Instruments ASG Manuale utente

Westinghouse

Westinghouse WH1000i Series Manuale utente