Agilent Technologies 8640b Manuale utente

Adapted from HP Service Sheet “D” WB0SMX

8640b Gear Set Replacement

DESCRIPTION

• A9, Peak De iation and Range Switch Assembly

A9 REMOVAL AND DISASSEMBLY PROCEDURE

1. Set PEAK DEV AT ON and RANGE switches fully ccw.

2. Remove PEAK DEV AT ON and RANGE switch knobs. The knobs are secure

with allen screws in the knobs.

3. Place instrument upside down and remove bottom cover (see Service Sheet

G).

Adapted from HP Service Sheet “D” WB0SMX

8640b Gear Set Replacement

4. Remove two nuts that secure A9 Assembly to front panel (located at switch

bushings).

Adapted from HP Service Sheet “D” WB0SMX

8640b Gear Set Replacement

5. Remove connectors A9A1P1 and A9A2P1 from jacks on A13 Assembly. Lift

rear of A9 Assembly until coupler slides apart. Gently slide the assembly back

and up to remove. Re-install assembly by setting both switch shafts fully ccw

and reversing the procedures in steps one through six. f Option 003 is

installed, remove both cables from the Reverse Power Assembly.

NOTE

The detents of both A9 Assembly and AlO Assembly switches must

align and

correspond to the same positions. Check that the actual RF output

frequency

agrees with the counter indication on all ranges. Refer to paragraph 5-

29.)

Adapted from HP Service Sheet “D” WB0SMX

8640b Gear Set Replacement

A9A1 and A9A2 Remo al

NOTE

For the following steps, orient the switch assembly with A9A1W1 and

A9A2W1 up.

Numbers in parentheses refer to items in the accompanying illustrated

parts breakdown.

6. Set both shafts fully ccw, and desolder the three wires attached to the

potentiometer terminals.

Adapted from HP Service Sheet “D” WB0SMX

8640b Gear Set Replacement

7. Remove retainer ring (49) at front of potentiometer shaft, and slide

potentiometer and its mounting plate out to the rear of the switch.

Adapted from HP Service Sheet “D” WB0SMX

8640b Gear Set Replacement

8. Remove retainer ring (1), washer (25), spring (24), and 4-contact rotor (23)

at rear of switch.

Adapted from HP Service Sheet “D” WB0SMX

8640b Gear Set Replacement

9. Remove two machine screws with lock and >at washers (31, 34, and 35) at

right rear of switch. Remove two machine screws (2 and 8) and accompanying

spacers (18) located at front left of switch.

Adapted from HP Service Sheet “D” WB0SMX

8640b Gear Set Replacement

10. Slide A9A2 Assembly (36) and gear mounting plate (37) o? of detent

shafts.

11. Slide T-shaft (17) with its accompanying combination gear (19) and planet

gears (15 and 42) o? of solid shaft (part of 50).

Adapted from HP Service Sheet “D” WB0SMX

8640b Gear Set Replacement

12. Loosen setscrews and remove combination gear (13) from solid shaft.

Adapted from HP Service Sheet “D” WB0SMX

8640b Gear Set Replacement

13. Loosen setscrews and remove spur gear (40) from hollow shaft (part of

47).

Steps 14 and 15 may be skipped at this point, if you are only replacing the

gearset. You have full access to the gears without further action...

14. Remove two machine screws (46) at front right of detent mounting plate

(4), and remove P.C. board support (41).

15. Slide A9A1 Assembly (11) o? of detent shafts.

Altri manuali Agilent Technologies Generatore portatile

Agilent Technologies

Agilent Technologies E4438C Istruzioni operative

Agilent Technologies

Agilent Technologies N5161A Manuale utente

Agilent Technologies

Agilent Technologies 75000 Series C Manuale utente

Agilent Technologies

Agilent Technologies ESG-D Series Guida alla configurazione

Agilent Technologies

Agilent Technologies N4971A Manuale utente

Agilent Technologies

Agilent Technologies ESG-D Series Guida rapida

Agilent Technologies

Agilent Technologies ESG series Manuale utente

Agilent Technologies

Agilent Technologies E4430B Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies 33120A Manuale utente

Agilent Technologies

Agilent Technologies N5161A Manuale utente

Agilent Technologies

Agilent Technologies 33210A Manuale utente

Agilent Technologies

Agilent Technologies E8241A Manuale utente

Agilent Technologies

Agilent Technologies ESG series Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies E4428C Manuale utente

Agilent Technologies

Agilent Technologies E4438C Manuale utente

Agilent Technologies

Agilent Technologies E8267C Manuale utente

Agilent Technologies

Agilent Technologies 8360B Manuale utente

Agilent Technologies

Agilent Technologies 8360B Manuale utente

Agilent Technologies

Agilent Technologies E8663B Manuale utente

Agilent Technologies

Agilent Technologies E8663B Manuale utente

Agilent Technologies

Agilent Technologies E8663B Manuale utente

Agilent Technologies

Agilent Technologies E4423B Guida rapida

Agilent Technologies

Agilent Technologies ESG series Manuale di installazione e funzionamento

Agilent Technologies

Agilent Technologies E4400B Manuale utente

Manuali Generatore portatile popolari di altre marche

Kohler

Kohler 20EORZ Manuale di istruzioni

Powerhorse

Powerhorse 83171 Manuale utente

HURST

HURST ML-630-SI Manuale utente

ETQ

ETQ TG4000 Manuale utente

Briggs & Stratton

Briggs & Stratton 40265 Guida all'installazione

ConMed

ConMed 7550 Manuale utente

Owon

Owon Waveform Generator Manuale utente

evertz

evertz 7700 Series Manuale utente

Power Stroke

Power Stroke PS906025 Manuale utente

Firefly

Firefly Cygnus CYG2400/460/24 Manuale utente

Draper

Draper PG950S Aggiornamento firmware

PowerBoss

PowerBoss PowerBoss Manuale utente

SDMO

SDMO SH 4000 Manuale utente

EINHELL

EINHELL STE 5500 Manuale utente

Wanco

Wanco WI3000P Manuale utente

Full Boar

Full Boar FBT-3300 Manuale utente

Dwyer Instruments

Dwyer Instruments ASG Manuale utente

Westinghouse

Westinghouse WH1000i Series Manuale utente