Allen-Bradley ArmorBlock 1732E Manuale utente

Installation Instructions

1732E ArmorBlock 2 Port Ethernet Module

Catalog Numbers 1732E-IB16M12R, 1732E-OB16M12R,

1732E-IB16M12DR, 1732E-OB16M12DR, 1732E-16CFGM12R,

1732E-IB16M12SOEDR, 1732E-8X8M12DR

Topic Page

Important User Information 2

Environment and Enclosure 3

Prevent Electrostatic Discharge 3

About the ArmorBlock 2 Port Ethernet Module 4

Catalog Number Explanation 5

Install the Module 5

Set the Network Address 6

Mount the Module 7

Product Dimensions 7

Connect the I/O, Network and Auxiliary Cables to the ArmorBlock Module 8

Interpret LED Indicators 13

Specifications 15

21732E ArmorBlock 2 Port Ethernet Module

Publication 1732E-IN004A-EN-E - November 2009

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of

the wide variety of uses for solid state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an

explosion in a hazardous environment, which may lead to personal injury or death,

property damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding

of the product.

ATTENTION Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you to identify

a hazard, avoid a hazard, and recognize the consequences.

SHOCK HAZARD

Labels may be on or inside the equipment, for example, a drive or motor, to alert

people that dangerous voltage may be present.

BURN HAZARD Labels may be on or inside the equipment, for example, a drive or motor, to alert

people that surfaces may reach dangerous temperatures.

1732E ArmorBlock 2 Port Ethernet Module 3

Publication 1732E-IN004A-EN-E - November 2009

Environment and Enclosure

Follow these guidelines for environment and enclosure information for this

equipment.

Prevent Electrostatic Discharge

Follow these guidelines when you handle this equipment.

ATTENTION This equipment is intended for use in overvoltage Category II applications (as

defined in IEC 60664-1), at altitudes up to 2000 m (6562 ft) without derating.

This equipment is considered Group 1, Class A industrial equipment according

to IEC/CISPR 11. Without appropriate precautions, there may be difficulties

with electromagnetic compatibility in residential and other environments due

to conducted and radiated disturbances.

This equipment is supplied as enclosed equipment. It should not require

additional system enclosure when used in locations consistent with the

enclosure type ratings stated in the Specifications section of this publication.

Subsequent sections of this publication may contain additional information

regarding specific enclosure type ratings, beyond what this product provides,

that are required to comply with certain product safety certifications.

In addition to this publication, see:

•Industrial Automation Wiring and Grounding Guidelines, Rockwell

Automation publication 1770-4.1, for additional installation

requirements.

•NEMA Standards 250 and IEC 60529, as applicable, for explanations of

the degrees of protection provided by different types of enclosure.

ATTENTION This equipment is sensitive to electrostatic discharge that can cause internal

damage and affect normal operation. Follow these guidelines when you

handle this equipment.

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wrist strap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•Use a static-safe workstation if available.

•Store the equipment in appropriate static-safe packaging when not in

use.

41732E ArmorBlock 2 Port Ethernet Module

Publication 1732E-IN004A-EN-E - November 2009

About the ArmorBlock 2 Port Ethernet Module

The EtherNet/IP ArmorBlock is a 24V DC I/O module that communicates

via EtherNet/IP. The sealed IP65, IP67 and IP69K housing of these modules

requires no enclosure. Note that environmental requirements other than IP65,

IP67 and IP69K may require an additional appropriate enclosure. I/O

connectors are sealed M12 style.

EtherNet/IP networks use advanced network technology, for example,

producer/consumer communication, to increase network functionality and

throughput.

EtherNet/IP ArmorBlock 16-Point I/O Module

(1) Functional Earth grounds the I/O block’s EtherNet/IP communication circuitry which is designed to

mitigate the effect of noise on the network. Refer to EtherNet/IP Connectors on page 9 for

connections.

(2) Protective Earth is provided for the grounding of field devices and is internally connected to each Pin 5 of

the M12 I/O connectors. Refer to I/O Connectors on page 8 for connections.

LINK 1 LINK 2

44945

Status LEDs

Auxiliary power

Functional Earth(1)

Node address

switches

Protective Earth(2)

EtherNet/IP D-Code

M12 connector

EtherNet/IP D-Code

M12 connector

M12 I/O connectors M12 I/O connectors

1732E ArmorBlock 2 Port Ethernet Module 5

Publication 1732E-IN004A-EN-E - November 2009

Catalog Number Explanation

Refer to the table for a description of the modules’ catalog numbers.

Install the Module

Refer to the following sections to install your module.

•Set the Network Address

•Mount the Module

•Connect the I/O, Network and Auxiliary cables to the ArmorBlock

Module

Cat. No. Description Network

Connector

Auxiliary

Power

1732E-IB16M12R 16 Channel 24V DC Digital Input Dual-Port

Ethernet Module Dual D-Code

M12 Single 4-pin

mini

1732E-OB16M12R 16 Channel 24V DC Digital Output Dual-Port

Ethernet Module

1732E-16CFGM12R 16 Channel 24V DC Configurable Digital I/O

Dual-Port Ethernet Module

1732E-IB16M12DR Diagnostic 16 Channel 24V DC Digital Input

Dual-Port Ethernet Module Dual D-Code

M12 Single 4-pin

mini

1732E-OB16M12DR Diagnostic 16 Channel 24V DC Digital Output

Dual-Port Ethernet Module

1732E-8X8M12DR Diagnostic 8-Input/8-Output 24V DC Digital I/O

Dual-Port Ethernet Module Dual D-Code

M12 Single 4-pin

mini

1732E-IB16M12SOEDR Diagnostic Sequence of Events 16 Channel 24V

DC Digital Input Dual-Port Ethernet Module Dual D-Code

M12 Single 4-pin

mini

61732E ArmorBlock 2 Port Ethernet Module

Publication 1732E-IN004A-EN-E - November 2009

Set the Network Address

The I/O block ships with the rotary switches set to 999 and DHCP enabled.

To change the network address, you can do one of the following:

•adjust the switches on the front of the module.

•use a Dynamic Host Configuration Protocol (DHCP) server, such as

Rockwell Automation BootP/DHCP.

•retrieve the IP address from nonvolatile memory.

The I/O block reads the switches first to determine if the switches are set to a

valid number. Set the network address by adjusting the 3 switches on the front

of the module (refer to the illustration on page 6). Use a small blade

screwdriver to rotate the switches. Line up the small notch on the switch with

the number setting you wish to use. Valid settings range from 001...254.

Network Address Example

When the switches are set to a valid number, the I/O block’s IP address is

192.168.1.xxx (where xxx represents the number set on the switches). The

I/O block’s subnet mask is 255.255.255.0 and the gateway address is set to

0.0.0.0. When the I/O block uses the network address set on the switches, the

I/O block does not have a host name assigned to it or use any Domain Name

Server.

If the switches are set to an invalid number (for example, 000 or a value

greater than 254 excluding 888), the I/O block checks to see if DHCP is

enabled. If DHCP is enabled, the I/O block asks for an address from a

DHCP server. The DHCP server also assigns other Transport Control

Protocol (TCP) parameters.

If DHCP is not enabled, the I/O block uses the IP address (along with other

TCP configurable parameters) stored in nonvolatile memory.

This example shows

the network address

set at 63.

44233

1732E ArmorBlock 2 Port Ethernet Module 7

Publication 1732E-IN004A-EN-E - November 2009

Mount the Module

Two sets of mounting holes are used to mount the module directly to a panel

or machine. Mounting holes accommodate #8 (M4) pan head screws. The

torque specification is 1.13 Nm (10 in-lb).

Product Dimensions

Refer to the mounting dimensions illustration to help you mount the modules.

LINK 1 LINK 2

44946

43.25 mm

(1.70 in.)

26.5 mm

(1.04 in.)

65 mm

(2.56 in.)

179 mm

(7.05 in.) 169 mm

(6.64 in.)

Front view Side view

81732E ArmorBlock 2 Port Ethernet Module

Publication 1732E-IN004A-EN-E - November 2009

Mount the Module in High Vibration Areas

If you mount the module in an area that is subject to shock or vibration, we

recommend you use a flat and a lock washer to mount the module. Mount the

flat and the lock washer as shown in the mounting illustration. Torque the

mounting screws to 1.13 Nm (10 in-lb).

High Vibration Area Mounting

Connect the I/O, Network and Auxiliary Cables to the ArmorBlock Module

The ArmorBlock EtherNet/IP family has 5-pin micro-style connectors. We

provide caps to cover the unused connectors on your module. Connect the

quick-disconnect cord sets you selected for your module to the appropriate

ports.

I/O Connectors

Refer to the pinout diagrams for the I/O connectors.

44766

Lock washer

Flat washer

1 2

Micro-style 5-Pin Input Female Connector

(View into connector)

Pin 1 Sensor source voltage

Pin 2 Input B

Pin 3 Return

Pin 4 Input A

Pin 5 PE

44807

1732E ArmorBlock 2 Port Ethernet Module 9

Publication 1732E-IN004A-EN-E - November 2009

EtherNet/IP Connectors

Refer to the pinout diagrams for the network connectors.

IMPORTANT Use the 1585D–M4DC–H: Polyamide small body unshielded or the

1585D–M4DC–SH: Zinc die-cast large body shielded mating connectors

for the D-Code M12 female network connector.

1 2

Micro-style 5-Pin Output Female Connector

(View into connector)

Pin 1 Not used

Pin 2 Output B

Pin 3 Return

Pin 4 Output A

Pin 5 PE

44807

1 2

Self-configuring Connector

(View into connector)

Pin 1 Sensor source voltage

Pin 2 Input or output B

Pin 3 Return

Pin 4 Input or output A

Pin 5 PE

44807

D-Code M12 Network Female Connector

(View into connector)

Pin 1 M12_Tx+

Pin 2 M12_Rx+

Pin 3 M12_Tx-

Pin 4 M12_Rx-

Pin 5 Connector shell shield FE

44808

10 1732E ArmorBlock 2 Port Ethernet Module

Publication 1732E-IN004A-EN-E - November 2009

The 1732E-16CFGM12R self-configuring module contains both input and

output functionality.

•If an I/O point is to be an output, dedicate that point as an output

with a wired load and energize it through a control program.

•Energized outputs show an associated active input that can be used as

a feedback mechanism to make certain that the output is on.

•If an I/O point is to be an input, wire the input device as normal and

leave the associated output de-energized at all times.

I/O Self-configure Circuitry

IMPORTANT Use two twisted pair CAT5E UTP or STP cables.

ATTENTION Make sure all connectors and caps are securely tightened to properly seal the

connections against leaks and maintain IP enclosure type requirements.

D-Code

M12 Pin

Wire Color Signal 8-way Modular

RJ45 Pin

1 White-Orange TX+ 1

2 White-Green RX+ 3

3 Orange TX- 2

4 Green RX- 6

Output scan list

Turn output on Output

circuit

Sensor or

actuator

Connector pin

Input is on

(Or output is on)

Input

circuit

43601

Input scan list

From PLC

To PLC

Altri manuali per ArmorBlock 1732E

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Allen-Bradley Unità di controllo

Allen-Bradley

Allen-Bradley FLEX I/O 1794-OB8EP Manuale utente

Allen-Bradley

Allen-Bradley 1732ES-IB16 Manuale utente

Allen-Bradley

Allen-Bradley 1772-MJ Manuale operativo

Allen-Bradley

Allen-Bradley 160-RS1 Manuale utente

Allen-Bradley

Allen-Bradley ProcessLogix R300.1 Manuale utente

Allen-Bradley

Allen-Bradley ArmorBlock MaXum B Series Manuale utente

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-IT4IM12R Manuale utente

Allen-Bradley

Allen-Bradley POINT I/O 1734-OB2 Manuale utente

Allen-Bradley

Allen-Bradley MicroLogix 1762-OW Manuale utente

Allen-Bradley

Allen-Bradley 1734-OB2 Manuale utente

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFM Manuale utente

Allen-Bradley

Allen-Bradley FLEX I/O ControlNet 1794-ACN15 Manuale utente

Allen-Bradley

Allen-Bradley DF1 Manuale utente

Allen-Bradley

Allen-Bradley Bulletin 160 DeviceNet Manuale utente

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-8IOLM12R Manuale

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-8IOLM12R Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Manuale utente

Allen-Bradley

Allen-Bradley FLEX Ex 1797-OB4D Manuale utente

Allen-Bradley

Allen-Bradley 1747-SN Manuale utente

Allen-Bradley

Allen-Bradley 1794-IE8 Series B Manuale utente

Allen-Bradley

Allen-Bradley C Series Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix 1756-OA8D Manuale utente

Allen-Bradley

Allen-Bradley ProcessLogix 1757 Series Manuale utente

Allen-Bradley

Allen-Bradley MicroLogix 1762-IQ8 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente