Allen-Bradley ControlLogix ControlNet B Series Manuale utente

Installation Instructions

ControlLogix ControlNet Interface Module

Catalog Numbers 1756-CN2, 1756-CN2R, Series B

Topic Page

Important User Information 2

European Hazardous Location Approval 3

North American Hazardous Location Approval 4

Environment and Enclosure 5

Prevent Electrostatic Discharge 5

The ControlNet Interface Module and Redundant Media 6

Understanding Standalone and Redundant Control 6

Example Redundant System 7

Before You Begin 8

Parts List 8

Identify Module Features 9

Set the Module’s Network Address Switches 10

Reset the Module to the Original Factory Settings 10

Keeper Configuration - Automatic Keeper Crossload 11

Prepare the Chassis for Module Installation 12

Determine Module Slot Location 12

Install the Module 13

Connect the Module to the Network 14

Remove the Module 18

Install or Remove the Module Under Power 18

Install the EDS File 19

Configure RSLinx Software to Use the USB Port 20

Set Up the USB Driver 21

Status Indicators 22

Module Status Indicator and Display 23

ControlNet Channel Status Indicators 29

Specifications 31

Additional Resources 35

2ControlLogix ControlNet Interface Module

Publication 1756-IN607A-EN-P - February 2008

Important User Information

Solid state equipment has operational characteristics differing from those of electromechanical

equipment. Safety Guidelines for the Application, Installation and Maintenance of Solid State Controls

(Publication SGI-1.1 available from your local Rockwell Automation sales office or online at

http://literature.rockwellautomation.com) describes some important differences between solid state

equipment and hard-wired electromechanical devices. Because of this difference, and also because of

the wide variety of uses for solid state equipment, all persons responsible for applying this equipment

must satisfy themselves that each intended application of this equipment is acceptable.

In no event will Rockwell Automation, Inc. be responsible or liable for indirect or consequential damages

resulting from the use or application of this equipment.

The examples and diagrams in this manual are included solely for illustrative purposes. Because of the

many variables and requirements associated with any particular installation, Rockwell Automation, Inc.

cannot assume responsibility or liability for actual use based on the examples and diagrams.

No patent liability is assumed by Rockwell Automation, Inc. with respect to use of information, circuits,

equipment, or software described in this manual.

Reproduction of the contents of this manual, in whole or in part, without written permission of Rockwell

Automation, Inc., is prohibited.

Throughout this manual, when necessary, we use notes to make you aware of safety considerations.

WARNING Identifies information about practices or circumstances that can cause an explosion in

a hazardous environment, which may lead to personal injury or death, property

damage, or economic loss.

IMPORTANT Identifies information that is critical for successful application and understanding of

the product.

ATTENTION Identifies information about practices or circumstances that can lead to personal

injury or death, property damage, or economic loss. Attentions help you identify a

hazard, avoid a hazard and recognize the consequences.

Labels may be on or inside the equipment (for example, drive or motor) to alert people

that dangerous voltage may be present.

Labels may be on or inside the equipment (for example, drive or motor) to alert people

that surfaces may reach dangerous temperatures.

SHOCK HAZARD

BURN HAZARD

ControlLogix ControlNet Interface Module 3

Publication 1756-IN607A-EN-P - February 2008

European Hazardous Location Approval

European Zone 2 Certification

(The following applies when the product bears the EEx Marking.)

This equipment is intended for use in potentially explosive atmospheres as defined

by European Union Directive 94/9/EC.

The Laboratoire Central des Industries Electriques (LCIE) certifies that this

equipment has been found to comply with the Essential Health and Safety

Requirements relating to the design and construction of Category 3 equipment

intended for use in potentially explosive atmospheres, given in Annex II to this

Directive. Compliance with the Essential Health and Safety Requirements has been

assured by compliance with EN 60079-15.

This equipment is not resistant to sunlight or other sources of UV radiation.

This equipment must be installed in an enclosure providing at least IP54 protection

when applied in Class I, Zone 2 environments.

This equipment shall be used within its specified ratings defined by Allen-Bradley.

Provision shall be made to prevent the rated voltage from being exceeded by transient

disturbances of more than 40% when applied in Class I, Zone 2 environments.

This equipment must be used only with ATEX certified backplanes.

IMPORTANT

4ControlLogix ControlNet Interface Module

Publication 1756-IN607A-EN-P - February 2008

North American Hazardous Location Approval

The following information applies when

operating this equipment in hazardous

locations.

Informations sur l’utilisation de cet

équipement en environnements dangereux.

Products marked "CL I, DIV 2, GP A, B, C, D" are suitable for

use in Class I Division 2 Groups A, B, C, D, Hazardous

Locations and nonhazardous locations only. Each product is

supplied with markings on the rating nameplate indicating

the hazardous location temperature code. When

combining products within a system, the most adverse

temperature code (lowest "T" number) may be used to help

determine the overall temperature code of the system.

Combinations of equipment in your system are subject to

investigation by the local Authority Having Jurisdiction at

the time of installation.

Les produits marqués "CL I, DIV 2, GP A, B, C, D" ne

conviennent qu'à une utilisation en environnements de

Classe I Division 2 Groupes A, B, C, D dangereux et non

dangereux. Chaque produit est livré avec des marquages sur

sa plaque d'identification qui indiquent le code de

température pour les environnements dangereux. Lorsque

plusieurs produits sont combinésdans unsystème, le code de

température le plus défavorable (code de température le plus

faible) peut être utilisé pour déterminer le code de

température global du système. Les combinaisons

d'équipements dans le système sont sujettes à inspection par

les autorités locales qualifiées au moment de l'installation.

WARNING EXPLOSION HAZARD -

• Do not disconnect equipment unless

power has been removed or the

area is known to be nonhazardous.

• Do not disconnect connections to

this equipment unless power has

been removed or the area is known

to be nonhazardous. Secure any

external connections that mate to

this equipment by using screws,

sliding latches, threaded

connectors, or other means

provided with this product.

• Substitution of components may

impair suitability for Class I,

Division 2.

• If this product contains batteries,

they must only be changed in an

area known to be nonhazardous.

AVERTISSEMENT RISQUE D’EXPLOSION –

• Couper le courant ou s'assurer

que l'environnement est classé

non dangereux avant de

débrancher l'équipement.

• Couper le courant ou s'assurer

que l'environnement est classé

non dangereux avant de

débrancher les connecteurs. Fixer

tous les connecteurs externes

reliés à cet équipement à l'aide

de vis, loquets coulissants,

connecteurs filetés ou autres

moyens fournis avec ce produit.

• La substitution de composants

peut rendre cet équipement

inadapté à une utilisation en

environnement de Classe I,

Division 2.

• S'assurer que l'environnement est

classé non dangereux avant de

changer les piles.

ControlLogix ControlNet Interface Module 5

Publication 1756-IN607A-EN-P - February 2008

Environment and Enclosure

Prevent Electrostatic Discharge

For additional information, refer to Industrial Automation Wiring and Grounding

Guidelines, publication 1770-4.1.

ATTENTION This equipment is intended for use in a Pollution Degree 2 industrial environment, in

overvoltage Category II applications (as defined in IEC publication 60664-1), at altitudes

up to 2000 meters (6562 feet) without derating.

This equipment is considered Group 1, Class A industrial equipment according to

IEC/CISPR Publication 11. Without appropriate precautions, there may be potential

difficulties ensuring electromagnetic compatibility in other environments due to

conducted as well as radiated disturbance.

This equipment is supplied as open-type equipment. It must be mounted within an

enclosure that is suitably designed for those specific environmental conditions that will

be present and appropriately designed to prevent personal injury resulting from

accessibility to live parts. The enclosure must have suitable flame-retardant properties to

prevent or minimize the spread of flame, complying with a flame spread rating of 5VA, V2,

V1, V0 (or equivalent) if non-metallic. The interior of the enclosure must be accessible only

by the use of a tool. Subsequent sections of this publication may contain additional

information regarding specific enclosure type ratings that are required to comply with

certain product safety certifications.

In addition to this publication, see:

Industrial Automation Wiring and Grounding Guidelines, for additional installation

requirements, Allen-Bradley publication 1770-4.1.

NEMA Standards publication 250 and IEC publication 60529, as applicable, for

explanations of the degrees of protection provided by different types of enclosure.

ATTENTION This equipment is sensitive to electrostatic discharge, which can cause internal damage

and affect normal operation. Follow these guidelines when you handle this equipment:

•Touch a grounded object to discharge potential static.

•Wear an approved grounding wriststrap.

•Do not touch connectors or pins on component boards.

•Do not touch circuit components inside the equipment.

•Use a static-safe workstation, if available.

•Store the equipment in appropriate static-safe packaging when not in use.

6ControlLogix ControlNet Interface Module

Publication 1756-IN607A-EN-P - February 2008

The ControlNet Interface Module and Redundant Media

Use the 1756-CN2 ControlLogix ControlNet series B module if

redundant media is not necessary. Applications requiring redundant

media must use the 1756-CN2R module.

Understanding Standalone and Redundant Control

You can use the 1756-CN2R series B modules for standalone or

redundant control. For standalone control, only one set of modules is

required. For redundant control, two ControlLogix chassis are

populated with identical pairs of modules called partners. The chassis

that performs active control is called the primary chassis and the

modules in the chassis are called primary modules. The other chassis

is called the secondary chassis and the modules in the chassis are

called secondary modules.

These installation instructions discuss both standalone and redundant

control; read them carefully to distinguish the procedures and

requirements for each type of control.

If you use redundant control, you must select the same ControlNet

network address for each set of partner modules (primary and

secondary). You must also place the partner modules in the same

corresponding slots in their respective redundant-control chassis

pair.

For more redundancy information, refer to the ControlLogix

Redundancy System User Manual, publication 1756-UM523F.

IMPORTANT

ControlLogix ControlNet Interface Module 7

Publication 1756-IN607A-EN-P - February 2008

Example Redundant System

Primary

Chassis

Secondary

Chassis

Redundant

ControlChassis

Pair

Remote I/O Chassis

1756-RM Module

ControlNet

Network

1756-CNB/CNBR

1756-CN2 Module

1756-CN2R Module

1756-RM Module

The 1756-CN2 and 1756-CN2R series B modules are supported in

both the local chassis (primary and secondary) and the remote

chassis (I/O chassis) of a ControlLogix redundancy system,

revision 16.5x.

IMPORTANT

8ControlLogix ControlNet Interface Module

Publication 1756-IN607A-EN-P - February 2008

Before You Begin

Before you install the module, make sure you know how to handle

the module. Refer to Prevent Electrostatic Discharge on page 5.

Parts List

You need all of the components shown.

1756-CN2 or 1756-CN2R

Module

1756-A4, 1756-A7, 1756-A10,

1756-A13, or 1756-A17 Chassis

1756-PA72, 1756-PA75,

1756-PB72, or 1756-PB75

Power Supply

1786-TPR, 1786-TPS,

1786-TPYR, or 1786-TPYSTaps(1) USB Cable (optional) Small Screwdriver

(1) 1786-TPSor 1786-TPYStaps are recommended for network connections.

COAX

BAOK

COAX

AOK

(2)

1756-CN2 and 1756-CN2R, series A modules use the 1786-CP cable. However, 1756-CN2 and 1756-CN2R,

series B modules use a USB cable for temporary network connections.

ControlLogix ControlNet Interface Module 9

Publication 1756-IN607A-EN-P - February 2008

Identify Module Features

These are the hardware components of the 1756-CN2 and 1756-CN2R

series B bridge modules.

Module

Status

Indicator

Channel A

BNC Connector

COAX

00 -

Factory Reset

on Power Up

(Invalid Network Address)

01 - 99

Normal Operation

(Valid Network Address)

Backplane

Connector

Front View Side View

Module Status

Alphanumeric

Display

ControlNet

Channel

Status

Indicators

USB Port

Channel B

BNC Connector

(1756-CN2R only)

Network Address Switches

(not shown) See page 10.

This module’s network

address is 23.

Side of Module

Front of Module

Top of Module

10 ControlLogix ControlNet Interface Module

Publication 1756-IN607A-EN-P - February 2008

Set the Module’s Network Address Switches

Use a small screwdriver to set the module’s network address

switches. For modules in a standalone chassis, you must specify a

unique ControlNet network address. You can select an address of

01...99 for modules in a standalone chassis. Address 00 is an invalid

ControlNet address.

Reset the Module to the Original Factory Settings

To reset the module to its original settings and clear all keeper

information (see page 11), complete the following steps.

1. Remove power from the chassis.

2. Remove the module from the chassis.

IMPORTANT The following procedure instructs you to remove power from the chassis

before removing the module. This is only necessary if the module is in a

Class I, Division 2 hazardous location. For more information, see Install or

Remove the Module Under Power on page 18.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Allen-Bradley Unità di controllo

Allen-Bradley

Allen-Bradley DF1 Istruzioni per il montaggio

Allen-Bradley

Allen-Bradley PowerMonitor 500 Manuale utente

Allen-Bradley

Allen-Bradley POINT I/O 1734-VHSC5 Manuale utente

Allen-Bradley

Allen-Bradley 1746-HSTP1 Manuale utente

Allen-Bradley

Allen-Bradley MicroLogix 1200 Manuale utente

Allen-Bradley

Allen-Bradley ArmorBlock 1732E Manuale utente

Allen-Bradley

Allen-Bradley 1791-16BC Manuale utente

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IV32 Manuale utente

Allen-Bradley

Allen-Bradley SLC 500 DeviceNet Manuale utente

Allen-Bradley

Allen-Bradley ControlNet 1786-RPFRL/B Manuale utente

Allen-Bradley

Allen-Bradley ArmorBlock Series Manuale

Allen-Bradley

Allen-Bradley ControlLogix 1756-DHRIO Manuale utente

Allen-Bradley

Allen-Bradley MicroLogix 1200 Manuale utente

Allen-Bradley

Allen-Bradley 1762-OF4 Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Foglio di istruzioni

Allen-Bradley

Allen-Bradley ArmorBlock 1732E-8IOLM12R Manuale

Allen-Bradley

Allen-Bradley SERCOS 1756-M03SE/A Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix DeviceNet 1756-DNB Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix 1756-OX8I Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix SynchLink 1756-SYNCH Manuale utente

Allen-Bradley

Allen-Bradley ControlLogix 1756-OV32E Manuale utente

Allen-Bradley

Allen-Bradley FLEX I/O 1794-IP4 Manuale utente

Allen-Bradley

Allen-Bradley 1771-OBN Manuale utente

Allen-Bradley

Allen-Bradley 1732ES-IB16 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente