Amazon 90DM160 Manuale utente
4000 Count Auto Ranging Digital Multimeter
Multimètre Numérique 4000Points à Sélection Auto de la
Plage de Mesure
4000er-Zählung Automatisch Messender Digitalmultimeter
Multimetro Digitale a Selezione Automatica del Campo di
Misurazione, 4000Conteggi
Multímetro Digital de Alcance Automático, Contador Hasta 4000
4000Counts Digitale Multimeter met Automatische Bereikinstelling
B083V7BMZR
10A
English . . . . . . . . . . . . . . . . . . . . . . . 3
Français . . . . . . . . . . . . . . . . . . . . . 32
Deutsch . . . . . . . . . . . . . . . . . . . . . 63
Italiano . . . . . . . . . . . . . . . . . . . . . . 94
Español . . . . . . . . . . . . . . . . . . . . 125
Nederlands . . . . . . . . . . . . . . . . . 155
3
EN
IMPORTANT SAFETY
INSTRUCTIONS
Read these instructions carefully and retain them for
future use. If this product is passed to a third party,
then these instructions must be included.
When using electrical appliances, basic safety precautions
should always be followed to reduce the risk of fire, electric
shock, and/or injury to persons including the following:
WARNING Risk of electric shock! Improper use of this
product can cause damage, shock, injury or death.
WARNING Risk of electric shock! The safety features of
this product may not protect the user if not used in accordance
with this user manual.
WARNING Risk of electric shock! Take special care while
working under wet conditions. Humid objects and air have an
increased conductivity.
CAUTION Risk of short circuit! Use the test probe
shrouds to avoid accidental short circuiting if the components
or test points are too near each other. Operation is limited to
CAT II applications when the insulated tips are removed from
one or both test probes. Refer to Specification in this manual for
maximum voltage ratings.
4
EN
WARNING Risk of electric shock! Use special care
when making measurements, if the voltages are greater than
25V~ RMS or 35V . These voltages are considered a shock
hazard.
WARNING Risk of electric shock! Keep fingers away
from the metal probe tips when taking measurements.
WARNING Risk of explosion! Do not use the product
near explosive vapors, dust or gases.
CAUTION Risk of injury! The probe tips are sharp for
accuracy. Be careful when handling and reattach the probe tip
shrouds after use.
• This product is intended for measurements on electrical
installations and is protected by doubleinsulation as per
EN61010-1 to CATIII600 V; Pollution Degree 2.
• This product must be used by trained users only.
• Do not measure current on a CATIII circuitry whose voltage
exceeds 600V.
• When measuring volts, do not switch to current/resistance
modes.
• Set the function switch to the appropriate position before
measuring.
• Set the function switch to the OFF position when not in use.
• Inspect the condition of the connector leads and the product
for any damage before operation. Replace any damaged
accessory before use. Consult a professional repair centre
for any other repairs.
5
EN
• Do not exceed the maximum allowable input range of any
measurement mode.
Mode Maximum Input
A~, A 10 A, 600 V fast acting fuse (max.
30seconds every 15minutes)
mA~, mA 500 mA, 600 V fast acting fuse
V~, V 600 V ~RMS /
Frequency,
Resistance,
Capacitance, Diode
Test, Continuity,
Temperature
250 V ~RMS /
Surge Protection: 8 kV peak per EN61010
• When changing ranges always disconnect the connector
leads from the circuit under test.
• Always discharge capacitors and remove power from the
device under test before performing diode, resistance or
continuity tests.
• Voltage checks on electrical outlets can be difficult and
misleading because of the uncertainty of connection to the
recessed electrical contacts. Do not use this product for
checking socket outlets. Use special equipment for checking
socket outlets.
• Comply with all applicable safety codes. Use approved
personal protective equipment when working near live
circuits − especially with regard to the possibility of arc flash
hazards.
• Always remove the connector leads before replacing the
battery or fuses.
6
EN
Battery Warnings
• Always insert batteries correctly with regards to polarity
(+ and –) marked on the battery and the product.
• Exhausted batteries should be immediately removed from
product and properly disposed.
• Keep batteries out of the reach of children.
• Do not dispose of batteries in fire.
• Remove batteries from product if it is not to be used for an
extended period of time.
• If the battery leaks, avoid contact with skin and eyes. Rinse
affected areas immediately with plenty of clean water, then
consult a doctor.
Explanation of Symbols
WARNING The signal word that indicates a hazard with
a medium level of risk which, if not avoided,
could result in death or serious injury.
CAUTION
The signal word that indicates a hazard
that if not prevented could result in minor or
moderate injury.
NOTICE Indicates a practical tip, advice or practice
not related to personal injury.
7
EN
This symbol stands for “Conformité Européenne”,
which means “Conformity with EU-directives”. With
the CE marking the manufacturer confirms that this
product complies with applicable European directives
and regulations.
This symbol, adjacent to another symbol or terminal,
indicates the user must refer to the manual for
further information.
This symbol, adjacent to a terminal, indicates that,
under normal use, hazardous voltages may be
present.
Product is protected by double insulation or
reinforced insulation.
Alternating current (AC).
Direct current (DC).
Fuse
Earth (ground) terminal/potential.
CAT II
600V
Product is designed to protect the user during
measurements performed on circuits directly
connected to the low voltage installation.
CAT III
600V
Product is designed to protect the user during
measurements performed in the building installation
(up to 600 V).
8
EN
Intended Use
• This product is intended to perform electrical measurements
on CAT III locations (3-phase and single phase distribution).
• This product covers CAT II and CAT I locations.
• This product may be used only under the conditions and for
the purposes for which it was designed.
• No liability will be accepted for damages resulting from
improper use or non-compliance with these instructions.
Before First Use
• Check the product for transport damages.
• Remove all the packing materials.
DANGER Risk of suffocation! Keep any packaging
materials away from children – these materials are a potential
source of danger, e.g.suffocation.
9
EN
Product Description
10A
A
B
D
E
FH
I
CJ
G
10
EN
K
L
P
O
MQR
N
ANon-contact voltage
indicator JHOLD/ button
BDisplay KBattery compartment
CRANGE button L500 mA fuse
DMODE button M10 A fuse
EFunction switch NTilt stand
F10A input jack OTest probes with
connector leads
GCOM input jack PProbe tip shrouds
HV/Ω/Temp/Hz/%
/mA/μA input jack QTemperature probe
IREL Relative button R
Temperature probe
adapter with protection
cups
Indice
Lingue:
Altri manuali Amazon Strumento di misura
