Amerec K2 Manuale utente

K2 Steamer Control and App

Install/Operating Instructions

4209-41 08-06-21 Technical Support: 1-320-286-3500 1-800-363-0251 [email protected] Page 1

Amerec K2 Steamer Control

and SaunaLogic App

For use with AK Steam Generators

WARNING

The K2 control operates on 5VDC and does

not present a shock hazard. Electric Shock

Hazard - High voltage exists within the steam

equipment. There are no user serviceable parts

in this equipment. All installation and service to

this equipment should be performed by quali-

ed licensed personnel.

Do not exceed 30 minutes in a steam bath.

Excessive exposure can be harmful to your

health. Excessive exposure can produce a

rapid pulse, light-headedness, weakness or

fainting. If you become uncomfortable or

experience any of the above conditions exit the

steam bath immediately.

Steam baths can put stress on the body. There-

fore a steam bath should be used only under a

doctor's direction if you:

Are pregnant

Have diabetes

Have a heart condition

Have high blood pressure

Have circulatory problems

Are under the inuence of alcohol

Are under the inuence of drugs

Are under the care of a physician

Are in generally poor health

Children should only use the steam bath under

close adult supervision.

Scald Hazard: Do Not Touch the steam head

or trim during operation as they are HOT. Stay

at least 12 inches away from the hot steam

escaping from the steam head.

Be careful when entering a steam bath. Escap-

ing steam from an overheated steam room may

cause injury.

REDUCE THE RISK OF

1. Exit immediately if uncom fortable, dizzy or slee py. Sta ying too long in

a heated area is capab le of causing overheating.

REDUCE THE RISK OF

Use care when enter ing or e xiting the steam room, floor ma y be slippe ry.

NOTE: For additional saf ety instr uctions, see o wner's manual .

CA UTION!

Do not contact steam head . Sta y at least 12" away

from hot steam escaping from the steam outlet .

OVERHE ATING AND SCALDING

2. Supe rvise children at all tim es.

3. Che ck with a doctor bef ore use if pregnant, diabeti c, in poor health or

under medical car e.

4. Breathing heated air in conjunction with consumption of alcohol, dr ugs

or medication is capab le of causing unconsciousnes s.

SLIPPING AND FA LL INJU RY

WARNING

FOR THE SAFETY OF YOU AND YOUR FAMILY PLEASE READ

THE WARNINGS TO THE RIGHT AND ALL INSTRUCTIONS BE-

FORE USING YOUR STEAMBATH.

POST "WARNING" LABEL OUTSIDE STEAM BATH FOR SAFETY

WARNINGS. POSTING IS REQUIRED ON OR ADJACENT TO

STEAM ROOM DOOR FOR ALL COMMERCIAL INSTALLATIONS.

SAVE THIS MANUAL

Thank you for purchasing your new Amerec steam generator. If we can be of any

assistance do not hesitate to call our Technical Support at 1-800-363-0251.

The K2 control is to be used only with a compatible AK steamer from Amerec. If

you have an older AK, contact Tech support for information about upgrading to a

compatible version.

The K2 does not come with a built in temperature sensor so a wall mounted sen-

sor must be installed in the steam bath.

The K2 may be installed on the wall either inside or outside the steam room. Only

one K2 may be installed. If a second control is desired, you may add an optional

K4 On/O󰀨 control or a K3 (with temperature and time adjustments). The K3 and

K4 may be installed inside or outside the room.

The K2 comes with a Wi-Fi module which allows using an app in addition to the

K2. The SaunaLogic app is free for android or iOS devices and communicates

with Alexa, Echo and Siri devices. The Wi-Fi module connects to the steamer with

a 25 ft (7,6 m) cable (provided) to allow positioning the module where it will have

the best communications with your Wi-Fi system.

4209-41 08-06-21 Technical Support: 1-320-286-3500 1-800-363-0251 [email protected] Page 2

K2 Steamer Control and App

Install/Operating Instructions

IMPORTANT SAFETY INSTRUCTIONS

1. READ AND FOLLOW ALL INSTRUCTIONS.

2. WARNING - To reduce the risk of injury, do not permit children to use this product unless they are closely

supervised at all times.

3. WARNING - To reduce the risk of injury:

a. The wet surfaces of steam enclosures may be slippery. Use care when entering or leaving.

b. The steam head is hot. Do not touch the steam head and avoid the steam near the steam head.

c. Prolonged use of the steam system can raise excessively the internal human body temperature and

impair the body’s ability to regulate its internal temperature (hyperthermia). Limit your use of steam to 10 -

15 minutes until you are certain of your body’s reaction.

d. Excessive temperatures have a high potential for causing fetal damage during the early months of

pregnancy. Pregnant or possibly pregnant women should consult a physician regarding correct exposure.

e. Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory

system problems, or diabetes should consult a physician before using a steam bath.

f. Persons using medication should consult a physician before using a steam bath since some medication

may induce drowsiness while other medications may a󰀨ect heart rate, blood pressure and circulation.

4. WARNING - Hyperthermia occurs when the internal temperature of the body reaches a level several

degrees above the normal body temperature of 98.6°F. The symptoms of hyperthermia include an in-

crease in the internal temperature of the body, dizziness, lethargy, drowsiness and fainting. The e󰀨ect of

hyperthermia include:

a. Failure to perceive heat:

b. Failure to recognize the need to exit the steam bath:

c. Unawareness of impending risk:

d. Fetal damage in pregnant women:

e. Physical inability to exit the steam bath: and

f. Unconsciousness.

WARNING - The use of alcohol, drugs or medication can greatly increase the risk of hyperthermia.

SAVE THESE INSTRUCTIONS

K2 Steamer Control and App

Install/Operating Instructions

4209-41 08-06-21 Technical Support: 1-320-286-3500 1-800-363-0251 [email protected] Page 3

STEAM GENERATOR

TEMPERATURE SENSOR

K2 CONTROL

STEAM ROOM

K2 CONTROL OVERVIEW

The K2 control is a low voltage wired control for use with Amerec’s AK series steam generators. The control requires an 8 con-

ductor CAT-5 cable (provided) to connect to the steamer. A temperature sensor (required) mounts inside the steam room and

connects to the steam generator.

The K2 uses touch screen switches to control the bath and options:

• start and stop the steam bath

• set or display the bath temperature *

• set the bath run time **

• set a delayed start time for the steam bath

• control low voltage room lights (optional)

• control a 2nd option, such as Amerec’s bluetooth connected speaker system (optional)

*The bath temperature may be displayed in either °F or °C, selected using a jumper on the steamer’s

circuit board.

** The bath time may be set for up to 60 minutes (default). A jumper on the steamer’s circuit board may

be used to set for a maximum bath time of up to 24 hours.

A typical installation

TEMPERATURE SENSOR

K2 CONTROL

Wi-Fi Module

Steamer Circuit Board

4209-41 08-06-21 Technical Support: 1-320-286-3500 1-800-363-0251 [email protected] Page 4

K2 Steamer Control and App

Install/Operating Instructions

Display shows current bath temperature

and bath time remaing while bath is on.

K2 OPERATION

K2 Steamer Control and App

Install/Operating Instructions

4209-41 08-06-21 Technical Support: 1-320-286-3500 1-800-363-0251 [email protected] Page 5

K2 Control

Display When power to the steamer is turned on, the K2 will set-up its program and display the software version (such

as S011) for about 5 seconds then the display will turn o󰀨. While the bath is on, the display alternates between showing

the current bath temperature and the time remaining before the bath automatically turns o󰀨.

Tap to decrease setting

Tap to increase setting

On/O󰀨 Tap to start and stop the steam bath

LED light control Amerec Spectra LED lights may be turned on or o󰀨 at any time and must be turned on/o󰀨 manually.

This control is dedicated to special amerec Spectra LED lights and must not be used with other lights.

The amerec LEDs provide white lighting or various colors

• Tap the icon to turn the lights on. To turn the lights o󰀨, tap and hold the icon 3 seconds or step through to the end of

the color selection.

• The lights will always start at white when rst turned on.

• Tap the icon to change the display colors.

Color sequence: White – Red – Green – Blue – Yellow – Aqua – Purple – Rotating colors – O󰀨

The amerec LEDs are dimmable

• Turn the lights on then press the + or – minus icons to adjust the brightness. The current brightness level is displayed

for 3 seconds.

• The brightness can be adjusted to 25%, 50%, 75% or 100% light output.

Option On/O󰀨 control Tap the icon to turn on or o󰀨 an optional device at any time. The device must be turned on/o󰀨

manually. This option does not turn o automatically after a bath.

• This control provides an on/o󰀨 switch control for low voltage, low current devices. It could be used to turn amerec’s

bluetooth speakers on/o󰀨, control amerec’s standard LED lighting, etc.

• Loads should be limited to about 2A and 30V or less.

Set Bath Run Time With the bath on, tap the icon then use the + and - icons to increase or decrease the bath run time.

Note: you must use a jumper on the steamer circuit board to choose between a max time of 60 minutes or 24 hours.

• In 60 minute mode (this is the default setting):

30 minutes default

setable 5 to 60 minutes

set in 5 min steps

• 24 hr mode (Note: in 24 hour mode the display shows remaining time in hours and minutes but without a :)

1 hour default

setable 1 to 24 hours

set in 1 hour steps

Set the Bath Temperature Turn the bath on then tap the temperature icon and use + and - icons to raise or lower

the bath’s temperature. Note: you must use a jumper on the steamer circuit board to choose between a display in °F

(default) or °C .

• Bath temperature is 120°F (49°C) default.

• settable 84°F (29°C) to 125°F (52 °C)

• Set in 1° steps.

Set delayed start A bath can be set to begin at a later time, such as setting it before going to sleep so it is ready to

use when you get up in the morning. See the General section for more details.

• With bath on, press icon then use + & - icons to raise or lower delay setting. The delay time is adjustable from 15

minutes to 24 hours in 15 minute steps. Default is 1 hour.

• After setting the delay time, wait about 3 seconds the bath will turn o󰀨 and the control will alternately display dlAy and

the delay time remaining. Note that the K2’s on/off icon will remain lit while the delay is counting down.

• After delay has run out, the bath will run with previously set bath time & temperature.

• Press the icon again to cancel the delay.

4209-41 08-06-21 Technical Support: 1-320-286-3500 1-800-363-0251 [email protected] Page 6

K2 Steamer Control and App

Install/Operating Instructions

NOTE: The complete App display is

shown above. The operations shown on

your phone or tablet will depend on your

screen size. If your display does not show

the complete view above, use your nger

to scroll the display up to show more of

the list.

K2 Saunalogic Steam App

Display The Display area shows the current room temperature in the

Steam Bath

Bath O󰀨/On Move the slider button to the right by sliding the round

button or tapping the open area next to the button. The slider will change

to green while the bath is on. To turn the bath o󰀨, move the slider to

the left .

Bath Time Remaining shows how long the bath will run before automati-

cally turning o󰀨 (in minutes). See below for setting the bath time.

Temp Set The bath temperature setting is shown at the right side of this

menu bar. To change the setting, tap >and the Temp setting screen will

appear. The current setting will appear with -and +signs along side the

temperature. Tap the -to lower the setting and + to increase it. When

done, tap OK.

Light The light option controls our Spectra LED lights. These lights

provide white or color lighting. Tap the >and the light setting screen will

appear. Select the color you want to use or to turn the lights o󰀨, then tap

OK.

Set Time To set how long the steam bath will run before automatically

turning o󰀨, tap the for hours or minutes and a setting screen will ap-

pear. Scroll up or down to the run time you want, then tap OK. Note that

the hours and minutes are set separately: The default maximum time is

60 minutes and suitable for most use. Note: you must use a jumper on

the steamer circuit board to choose between a max time of 60 minutes

(default) or 24 hours .Contact Amerec Technical Support for assistance

with this change.

Option 2 If you choose a low voltage option which is controllable by an

on/o󰀨 switch, you can control it with this option. Connect the control line

to a relay on the steamer’s circuit board then run the switched output

from the board to the option. Use the same actions as for the bath O󰀨/On

switch to turn this option’s switch on and o󰀨. Contact Amerec Technical

Support for assistance with this.

Set Delay Time You may set the bath to turn itself on after a delay, such

as when you want the bath ready to use when you get up in the morning.

Turn the bath on then tap the hours or minutes icons as you did in Set

Bath Time and adjust the length of delay you want. When nished, the

bath will turn o󰀨 and the displays on the K2 and the App will alternately

show delay and the time remaining before the bath starts. Note: the delay

time will be shown in minutes.

C/F This bar show the temperature scale used for the displayed bath

temperature. You cannot change this through the App. To select °C or °F

(default setting), you must use a jumper on the steamer circuit board to

change the setting.

K2 Steamer Control and App

Install/Operating Instructions

4209-41 08-06-21 Technical Support: 1-320-286-3500 1-800-363-0251 [email protected] Page 7

General Information

The displays on the K2 and App show more than just the temperature (and remaining bath time on the K2)

K2 Program When power is turned on to the steam generator, The K2 will start up, then show its software version for 5 seconds.

This can be good information to have when contacting Technical Support with operating issues.

Temperature Sensing There are three error codes associated with the temperature sensing operations:

This indicates a missing or damaged steam room temperature sensor. It could be a missing or malfunctioning sensor, a

bad cable, or other problems. If the problem is corrected, simply turn the bath o󰀨 and back on again and the temperature

displays should be ne again. If you have issues, please contact Technical Support.

This indicates a shorted steam room temperature sensor. It could be a malfunctioning sensor, corroded connectors, a

damaged cable (such as a staple through the cable, or other problems. If the problem is corrected, simply turn the bath

o󰀨 and back on again and the temperature displays should be ne again. If you have issues, please contact Technical

Support.

This indicates a steam room temperature measured much too hot. If you see this reading, immediately turn the bath o󰀨

until the problem is found and corrected. There is a risk of being scalded if the room overheats.Once the problem

is corrected, you must turn the steamer’s power o󰀨 and back on again to reset the error circuit. This is done to ensure

you know there was a problem so you can have it xed before resuming operation. If you have issues, please

contact Technical Support.

Defaults:

Steam Bath Temperatures may be set in 1° steps from 84°F (29°C) to 125°F (52°C). The factory setting is 120°F (49°C).

Steam Bath Run times are up to 60 minutes or up to 24 hour maximum, as set using a jumper on the steamer’s circuit board..

• 60 minute mode: 30 minutes default, adjustable from 5 to 60 minutes in 5 minute steps. While setting, the display

shows followed by the minutes.

• 24 hour mode: 1 hour default, adjustable from 1 to 24 hours in 1 hour steps. While setting, the display

shows followed by the minutes.

Light Option: Spectra Lights provide white or colored light from the same LED light. The light will always start at white after

power has been turned o󰀨 or after the lights have been turned o󰀨.

Delay Start start times are settable for up to 24 hours and must be re-set for each session. The default delay is 1 hour. Always

make sure the steam room is ready for a bath before starting a delay: no towels in the room, door closed, and so on.

4209-41 08-06-21 Technical Support: 1-320-286-3500 1-800-363-0251 [email protected] Page 8

K2 Steamer Control and App

Install/Operating Instructions

General Information (continued)

Light Option The LED lights use a special control circuit to give you good control of their appearance. The circuits are

dedicated to Amerec’s Spectra LEDs and must not be used with any other LED or Light.

• When rst turned on, the lights will always start as White.

• On the K2: Turn the lights on by tapping the light icon. To turn them o󰀨 again, scroll through to the end of the colors

or press the icon for about 3 seconds. Note: the lights do not turn o automatically, they must be turned o manually.

• The K2 can change the LEDs colors (in sequence): press the icon quickly to step through White - Red - Green - Blue -

Yellow - Aqua - Purple - Rotating colors - O.

• The K2 may be used to dim the lights. On the K2, turn the lights on then use the + and - to adjust the brightness up or

down. The light output can be adjusted to 25, 50, 75 or 100% of full brightness. The app cannot adjust brightness.

• On the App: Turn the lights on by tapping the Light Option’s icon the choose a color from the settings. To turn them o󰀨

again, press the then choose O󰀨 in the settings. Note: the lights do not turn o automatically; they must be turned o

manually.

• The App can change the LEDs colors (in sequence) using the settings to step through O - White - Red - Green - Blue -

Yellow - Aqua - Purple - Rotating colors

Delayed Start can be set to begin at a later time, such as setting it before going to sleep so it is ready to use when you get

up in the morning. Start times are settable for up to 24 hours and must be re-set for each session. Always make sure the

steam room is ready for a bath before starting a delay: no towels in the room, door closed, and so on.

• Default delay is 1 hour

• Delay times can only be set after turning the bath on. Once the delay is started,

• the K2 will alternately show the remaining time before the bath is scheduled to start and

• the app will continue to show that the bath is on and the delay settings will scroll down in

1 hour and in 5 minute steps

• K2 Delay time is adjustable from 15 minutes to 24 hours in 15 minute steps

• App delay time minutes are adjustable from 5 to 60 minutes in 5 minute steps and delay hours are

adjustable from 1 to 24 hours in 1 hour steps

Technical Support

575 Cokato St E

Cokato, MN 55321

Phone 320-286-3500

1-800-363-0251

email: [email protected]

Indice

Altri manuali Amerec Sistema di controllo

Amerec

Amerec T100 Manuale utente

Manuali Sistema di controllo popolari di altre marche

Pentair Pool Products

Pentair Pool Products Compool Manuale utente

ComfortNET

ComfortNET CTK04 Manuale utente

Fireye

Fireye InSight II 95DSS3 Manuale utente

CAME

CAME G3000 Manuale utente

Idemia

Idemia MorphoAccess VP MD Manuale utente

Axis

Axis P1445-LE-3 Manuale utente

HEIDENHAIN

HEIDENHAIN TNC 150 B Manuale utente

CNC-Step

CNC-Step High-Z T-Series Manuale utente

Doosan

Doosan DVF Series Manuale utente

Honeywell

Honeywell KAP 140 Manuale utente

Honeywell

Honeywell vk41 series Manuale utente

AirBench

AirBench FPW Guida all'installazione

Cypress

Cypress HHR-3160 Manuale utente

CAME

CAME GLT40AOS Manuale utente

Zonex

Zonex GEN II -VVT Guida utente

Altronics

Altronics K 9650 Manuale utente

micro-trak

micro-trak RoadMaster Manuale utente

micro-trak

micro-trak Calc-An-Acre II Manuale utente