American Dynamics Illustra 600 Manuale utente

illustra 600/610 Outdoor Wide Angle HD Mini-dome

Quick Start Guide

Version: 20110902

8200-2755-0700 A0

Under copyright laws, the contents of this manual may not be copied, photocopied, reproduced,

translated or reduced to any electronic medium or machine-readable form, in whole or in part, without

Reserved.

American Dynamics

6600 Congress Avenue

Boca Raton, FL 33487 U.S.A.

Notice of Use

This manual is designed for administrators and users of the network camera. Please read it

carefully before use. All requirements should be followed before using this camera.

We are not responsible for any technical or typographical errors and reserve the right to change

the product and manuals without notice.

Keep this document for future reference.

The camera is intended to be supplied from power source either 24V AC or PoE complying with

LPS requirement. Only connect the camera to this required power system.

The camera must be installed on a solid mounting surface.

Keep the camera and other accessories dry.

We are not responsible for any damage caused by inappropriate use.

All the installation should be performed by qualified personnel.

For outdoor application with a power supply: If the power supply is installed outdoors, it shall be a

listed rainproof/raintight Class 2/LPS power supply or a listed Class2/LPS power supply

complying with UL 60950-1 Part 1 and Part 22.

For wiring method for the power source: The wiring method should comply with Article 725 and

300 in National Electrical Code for Class 2 circuits and Wiring in Ducts.

1. Camera Installation

Accessory List

Security Torx Key x 1

Screw hole plug x 4

Screw x4

Anchor x 4

Guide Pattern Template x 2

CD-ROM x 1

Quick Start Guide x 1

Mounting the Camera

Step 1. Preparation – Remove the dome cover, camera liner and back case

1. Use the supplied security torx key to loosen

(but not remove) the three cover screws.

2. Remove the camera liner.

3. Loosen the three screws (marked with

triangle icon) on the dome base.

4. Remove the back case.

2 Quick Start Guide

1. Camera Installation

Step 2. Use the template to mark-out and prepare the mounting area

Method 1: To flush mount using screws

1. Create a circular opening in the mounting surface with

a diameter of 120 mm (4.7”) with tolerances of -0/+5 mm (-

0/.0.2”).

2. Create three 6 mm (0.2”) holes at the T3 template

positions. Then insert the screw anchors into the holes.

Notes:

- Not intended for drop ceiling installation without

appropriate lanyard.

- Not intended for installation in ceilings used for

environmental air return.

Method 2: To surface mount

1. According to your needs, create 6 mm (0.2”) holes at the T1/T2 template positions. Then insert the

screw anchors into the holes.

2. If you want to feed wiring from the hole on the top of the back case, create a circular opening (bottom

conduit hole) in the mounting surface.

Method 3: To surface mount using junction box

No need to mark-out and prepare the mounting areas. Skip to next section for mounting instructions.

1. Camera Installation

Step 3. Connect the wiring and make adjustments

AC Power: Connects to AC 24V power adapter. If you are to use power from Ethernet

connection, this connector is not used when the power is provided by PoE.

IP Network Connector: Connects to the LAN port of a standard 10Base/100Base-TX device,

e.g., hub, switch or router.

Audio In: Connects to an external microphone.

Audio Out: Connects to speaker.

Alarm In 1 & 2: Connects to devices that trigger alarm signals. Up to two 2 input devices can be

connected.

Alarm Out: Connects to device that responds to alarm signals, such as buzzers or lights.

GND: Ground (electricity) in electrical circuits

Note

To connect the Audio In/Out, Alarm In/Out or GND wires, press the relevant spring terminal tab

inward using an appropriate small tool and insert the wire into the opening. Then release the tab to

secure the wire.

Spring terminal tab

4 Quick Start Guide

1. Camera Installation

Micro SD Video System

Default Video Out

Reset

Video System: PAL / NTSC system switch. Default is NTSC. Use a suitable small tool to operate

the switch.

Note:

After switching the video system mode from NTSC to PAL or vice versa, you have to restore

defaults to apply the changes. You can do this by either of these methods:

1. Press the Default button on the camera and release within 4 seconds to restart the camera.

2. Enter the web-based illustra utility > System > Firmware and press the Factory Default

button.

Micro SD: Micro SDHC card slot.

Default:

- Factory Default: Press and release within 4 seconds to restart the camera and restore factory

defaults, excluding IP settings*.

- Hardware Factory Default: Press for more than 5 seconds and then release to restart the

camera and restore factory defaults, including IP settings*.

*The IP settings include DHCP, IP address, subnet mask, default gateway, DNS and HTTP

port, which are configured under Network > IP & Ethernet in the illustra utility .

Reset: Using a paper clip or thin object, press the button for at least one second and release to

restart the camera.

Video Out: Analog video out RCA jack. Connects to video in connector of a monitor.

1. Camera Installation

Step 4. Mount the dome enclosure

Method 1: To flush mount the dome using screws

1. Fasten the three TP4 screws to the inserted anchors to secure the dome enclosure in place.

2. Adjust the focusing position by rotating and panning the camera base. When rotating the camera base,

do not rotate it past the stop point.

3. Loosen the Zoom/Focus lever and adjust the lens. After adjustment is done, re-tighten the Zoom and

Focus levers.

Zoom: Adjust the zoom lever for desired image view.

Focus: Adjust the focus lever for optimum picture sharpness.

Zoom (Tele/Wide) lever

Focus (Near/Far) leve

4. Use the supplied security torx key to tighten the three cover screws to replace the dome cover.

5. Use the supplied Allen key to tighten the three cover screws to replace the dome cover.

6. Finally, insert the screw hole plugs to the three cover screws.

6 Quick Start Guide

1. Camera Installation

Method 2: To surface mount

1. According to your needs, use the top or side conduit hole on the back case for cable entry and connect

the wiring. Then mount the back case on a surface with screws.

2. Align the back case and the lens, and then fasten the TP4 screws into the inserted anchors. There is a

red dot on the base case and the lens base respectively. Use the dots to align the case and the base.

Use the red dots on back

case and lens base fo

alignment.

If you are going to use the side conduit hole, note that:

Use a 3/4" NPT (National Pipe Thread) pipe to feed the cables.

Before inserting the pipe to the side conduit hole, use a tape to seal the threads of the pipe.

Wrap at least 12 full loops of seal tape around the threads. Ensure that all the 100mm of tape is

wrapped around the threads of the pipe to ensure a tight seal and to prevent leaks.

Ensure all areas of the thread on the pipe are covered with seal tape.

Only those seal tapes complying with the UL’s requirements should be considered (Category

Code: JNGR).

1. Camera Installation

3. Adjust the focusing position by rotating and panning the camera base. Note that the back case side

conduit hole is the point where the camera will not rotate past.

4. Loosen the Zoom/Focus lever and adjust the lens. After adjustment is done, re-tighten the Zoom and

Focus levers.

Zoom: Adjust the zoom lever for desired image view.

Focus: Adjust the focus lever for optimum picture sharpness.

5. Fit the camera liner over the camera base so that it snaps into place.

5. Use the supplied security torx key to tighten the three cover screws to replace the dome cover.

7. Finally, insert the screw hole plugs to the three cover screws.

8 Quick Start Guide

Altri manuali per illustra 600

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali American Dynamics Telecamera di sicurezza

American Dynamics

American Dynamics ADCDW Series Manuale utente

American Dynamics

American Dynamics IP speedDome Ultra 8 Manuale

American Dynamics

American Dynamics ADCSHR2412N Manuale utente

American Dynamics

American Dynamics IP speedDome Ultra 8 Istruzioni di installazione e manutenzione

American Dynamics

American Dynamics ADC531 Manuale utente

American Dynamics

American Dynamics SpeedDome Ultra Manuale

American Dynamics

American Dynamics ADCA330CN Manuale utente

American Dynamics

American Dynamics ADC780 Manuale utente

American Dynamics

American Dynamics SpeedDome Optima LT Istruzioni di installazione e manutenzione

American Dynamics

American Dynamics SpeedDome Ultra VIIE Istruzioni di installazione e manutenzione

American Dynamics

American Dynamics SensorRail AD2079 Manuale utente

American Dynamics

American Dynamics SpeedDome Ultra Drone II Manuale utente

American Dynamics

American Dynamics SpeedDome Ultra Drone III Manuale utente

American Dynamics

American Dynamics ADCPBW Manuale utente

American Dynamics

American Dynamics ADCI625-P221 Manuale utente

American Dynamics

American Dynamics ADCDH Manuale utente

American Dynamics

American Dynamics ADC721B Manuale utente

American Dynamics

American Dynamics ADC860 Manuale utente

American Dynamics

American Dynamics Discover Indoor Manuale utente

American Dynamics

American Dynamics Illustra Flex Series Manuale utente

American Dynamics

American Dynamics Illustra Flex Series Manuale utente

American Dynamics

American Dynamics Tyco Discover Series Manuale utente

American Dynamics

American Dynamics ADC720D Manuale utente

American Dynamics

American Dynamics ADC 660N Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche

Okina USA

Okina USA SIR36-870VF650LP Manuale utente

Divio

Divio NDR155PA Manuale utente

Canon

Canon VB-C500D Manuale utente

Easy Access

Easy Access EasyGuard Manuale utente

Vivotek

Vivotek FD9389-EHV-v2 Manuale utente

TUYA

TUYA COSMO W2 Manuale utente

Eusso

Eusso UNC7500-IR Guida all'installazione

urmet domus

urmet domus 1096/204 Manuale utente

VC VC20 series Manuale utente

Axis

Axis Q1614 Manuale utente

ieGeek

ieGeek DD201 Manuale utente

VADDIO

VADDIO ClearVIEW HD-USB PTZ 999-6990-000 Manuale utente

Vicon

Vicon V662-D-1 Istruzioni operative

Grundig

Grundig GCH-K0274P Manuale utente

Lorex

Lorex VANTAGE LBC7032 Manuale utente

4xem

4xem WPT Manuale utente

Samsung

Samsung SCV-3082 Manuale utente

Vitek

Vitek VTC-C544 Manuale utente

American Dynamics illustra 600 Manuale utente

Manuali Telecamera di sicurezza popolari di altre marche