American Time DSY261RSxE Manuale utente

Installation and Operation Manual

Part # H004825

Rev. 1

August 2015

DSY261RSxE

Digital Clock/Elapsed

Time Indicator

with Code Blue

DSY261RSxE Owner's Manual

Electrical Shock Hazard

WARNING: Hazardous voltage in electrical equipment can cause severe personal injury or death. Inspection,

installation, and preventive maintenance should only be performed on equipment to which power has been turned

off, disconnected and electrically isolated so no accidental contact can be made with energized parts.

Electrostatic Sensitive Devices

CAUTION: This equipment contains electronic devices that are sensitive to static electric charges. To guarantee

protection for the circuitry of this unit, it is required that electrostatic handling precautions be observed

when installing or repairing this equipment. Any technician or other personnel working on this unit must

wear a static grounding wrist strap or similar device to provide protection of sensitive components.

ATTENTION

OBSERVE PRECAUTIONS

FOR HANDLING

ELECTROSTATIC

SENSITIVE

DEVICES

DSY261RSxE Owner's Manual Table of Contents

American Time

140 3rd Street South

PO Box 707

Dassel, MN 55325-0707

Phone: 800-328-8996

Fax: 800-789-1882

american-time.com

Important Installation and Warranty Information ....................................................................................................4

Specications ............................................................................................................................................................5

Description.................................................................................................................................................................6

DSY261RSxE Digital Clock/Timer ....................................................................................................................6

ATSTCS Control Station ...................................................................................................................................7

Installation Instructions ...........................................................................................................................................8

DSY261RSxE Installation Instructions................................................................................................................8

ATSTCS Installation Instructions ........................................................................................................................9

Operation ................................................................................................................................................................10

Power Up .......................................................................................................................................................10

Setting Time ..................................................................................................................................................10

Setting the Up Counter Preset Time ................................................................................................................10

Up Counter Elapsed Time Operation................................................................................................................11

Setting the Down Counter Preset Time ...........................................................................................................11

Down Counter Elapsed Time Operation...........................................................................................................11

Free Running Clock Operation .......................................................................................................................12

Synchronous Secondary Clock Operation ......................................................................................................12

Code Blue.................................................................................................................................................................13

Operation .......................................................................................................................................................13

Wiring ............................................................................................................................................................13

Important Considerations ...............................................................................................................................14

Maintenance ............................................................................................................................................................15

Appendix 1: Wiring For 3-Wire Secondary Clocks.....................................................................................................16

Appendix 2: Operators Flowchart.............................................................................................................................17

DSY261RSxE Owner's Manual

IMPORTANT INSTALLATION AND WARRANTY INFORMATION

WARRANTY INFORMATION: American Time (the Manufacturer) provides a limited warranty to the Original Purchaser of this

product. The Original Purchaser is the party to whom the Manufacturer issued its Sales Order, generally the Manufacturer’s

distributor. In order to preserve this warranty, it is important that only persons who have been properly trained and authorized by

the Manufacturer service the product.

Other parties involved in the installation of this product may have also provided a warranty, which may be different than that of the

Manufacturer. The Manufacturer will only be responsible to the Original Purchaser and only for the

Manufacturer’s own warranty. For further information regarding the Manufacturer’s warranty, contact the Original

Purchaser.

OWNER’S MANUAL: The owner’s manual does not purport to cover all the details or variations in the equipment described,

nor does it provide for every possible contingency to be met in connection with installation, operation and maintenance. All

specications subject to change without notice. Should further information be desired or should particular problems arise which

are not covered sufciently, the matter should be referred to the Installer or Original Purchaser listed below.

INSTALLER INFORMATION

COMPANY: INSTALLER: PHONE:

ADDRESS: CITY: STATE: ZIP:

DATE INSTALLED: INSTALLER’S SIGNATURE:

ORIGINAL PURCHASER INFORMATION

COMPANY: PHONE:

ADDRESS: CITY: STATE: ZIP:

PURCHASER’S PURCHASE ORDER NO:

DATE PURCHASED:

ATS SALES ORDER ACKNOWLEDGMENT NO.:

ORIGINAL PURCHASER’S SIGNATURE:

NOTE: A copy of the above-completed information may be required by the Manufacturer for authorization of Warranty services.

DSY261RSxE Owner's Manual Specications

GENERAL

Weight: ..............................Digital Clock/Timer ............................... 4.0 lb.

...............................ATSTCS Control Station ........................... 0.27 lb.

External Dimensions:.........Digital Clock/Timer ............................... 6.1"h x 12"w x 3.5"deep

ATSTCS Control Station ........................... 4.63"h X 4.56"w X 1.25"deep

SPECIFICATIONS

ELECTRICAL

Power Requirements (Digital Clock/Timer only):

Line Voltage: ..................................................................................... DSY261RSAE and DSY261RSPE -120vac 60Hz

DSY261RSBE - 24vac 60Hz

DSY261RSKE - 220vac 60Hz

DSY261RSKE50H - 220vac 50Hz

Note: Voltage is set at factory. See above part number sufx for reference.

Battery:............................................................................................... 9vdc Rechargeable Ni-Cad Battery

Battery Charger: ................................................................................ 9vdc Direct Current source with

current limiting resistor.

Maximum Current (Digital Clock/Timer only): .................................... 120vac 60Hz - 130mA (max), 101mA (avg)

24vac 60Hz -

220vac 60Hz -

220vac 50Hz -

Memory Retention on Loss of Line Voltage: ..................................... 4 hours with fully charged battery

Distance of ATSTCS from Digital Clock/Timer:................................. 30-ft maximum with 22 AWG stranded wire

............................................................................................... with minimum 1/32" thick insulation

Clock Circuits: ................................................................................... 3.0mA. max. @ 24vac/120vac

Code Blue Circuits: ............................................................................ 3.0mA. max. @ 12vac/vdc-30vac/vdc

ENVIRONMENTAL

Ambient Operating Range: ................................................................ 10°C to 49°C (50°F to 120°F)

Recommended Storage Temperature: .............................................. -30°C to 45°C (-22°F to 113°F)

............................................................................................... for six months maximum

Humidity:............................................................................................ 85 %RH at 30°C (86°F)

OPERATION

Modes Available:................12 hour or 24-hour non-system clock

12 hour secondary clock

Incrementing timer with programmable preset value and start/stop capability

Decrementing timer with programmable preset value and start/stop capability

Code Blue incrementing timer

Accuracy: .............................................................................with line voltage applied - line synchronous

with line voltage not applied - ± 0.005 % at 25°C

Indications: ........................Digital Clock/Timer .....................hours and minutes - 2.3", bright red, seven segment LED’s

hours and minutes are separated by a colon

seconds - 1", bright red, seven segment LED’s

ATSTCS Control Station ..............2 second audible alarm

DSY261RSxE Owner's Manual

Appendix Maintenance

Code Blue

Operation Installation Description

Clock/Timer Description

START/STOP RESET

INCREMENT ENTER

RUN

SET

DOWN

CLOCK

4 9/16”

4 1/2”

Control Station

”

6.1”

3.5”

ATSTCS Control Station

The DSY261RSxE is a six-digit digital multi-function clock/timer which can be used as an up or down counting elapsed

timer with an optional Code Blue trigger. The elapsed timers can be started, stopped, resumed, and reset. Both timer modes

have a programmable preset value. When the timer reaches the preset value, a two-second audible alarm sounds from

the ATSTCS control panel. The Code Blue up counting elapsed timer will override all other modes of operation if used. The

DSY261RSxE can function as a 12-hour or 24 hour stand-alone clock or can be wired as a 12-hour secondary clock for

synchronous time.

Digital Clock/Timer

DSY261RSxE Owner's Manual

AppendixMaintenance

Code Blue

OperationInstallationDescription

Control Station Switch Functions

START/STOP RESET

INCREMENT ENTER

RUN

SET

DOWN

CLOCK

RESET

ENTER

RUN

SET

DOWN

CLOCK

START/STOP

INCREMENT

Run/Set Switch -

Set Position: This position is used to set the clock or a preset up or down counting time (Timer). It is

also used to reset the Code Blue timer.

Run Position: This position is used to permit Clock/Timer to operate.

Up/Clock/Down Switch -

Up Position: This position is used to choose up counting elapsed timer mode.

Clock Position: This position is used to choose clock mode.

Down Position: This position is used to choose down counting elapsed timer mode.

Start/Stop/Increment Switch -

This button is used to start, stop, and resume timer count, when Run/Set Switch is in the Run

position (Code Blue timer can only be stopped).

This button is also used to increment/advance the number value being set when the Run/Set Switch

is in Set position.

Reset/Enter Switch -

This button is used to return a timer (excluding the Code Blue timer) to the beginning of its count, when

the Run/Set Switch is in Run position.

This button can also be used to select a eld (i.e. format, minute digits, hour digits) when the Run/

Set Switch is in Set position.

DSY261RSxE Owner's Manual

Appendix Maintenance

Code Blue

Operation Installation Description

Clock/Timer Installation

The Digital Clock/Timer can be mounted to a single or double gang box. To install the Digital Clock/Timer, follow the

instructions below. Ensure that installation conforms to the National Electrical Code and local wiring codes.

CAUTION: Electric Shock Hazard! Ensure that NO electrical power is present on any wire before installation.

uRemove the 6-32 black screw on the top of the clock which secures the back mounting plate. Mount the back plate to

a single or double gang box. See Figure 2 below.

vMake electrical connections (hot, neutral, ground and optional correction wires) to non-switched electrical circuit

wiring using UL approved wire nuts. Route eld wiring away from sharp projections, corners and internal components.

For Molex, connect white to neutral/common, black to positive/hot, green to ground and red to optional correction line

if using a wired master. Note: Voltage and frequency is set at the factory. See part number sufx reference.

120vac 60 Hz (DSY261RSAE and DSA261RSPE) 24vac 60 Hz (DSY261RSBE)

220vac 60Hz (DSY261RSKE) 220vac 50Hz (DSY261RSKE50H)

wPull the ten wires from the clock to the control station. Keep these ten wires separate from the high voltage wires.

See Figure 1 below. Note: there are two wires (white and green) in the bundle that are not used.

xJoin the two Molex connectors together, placing excess wiring and Molex connectors into the gang box.

ySlide the clock onto the metal mounting bracket installed in Step 1 and reinsert 6-32 screw from the top of the clock

into the mounting bracket hole. See Figure 2 below.

zConnect eld wiring interconnecting the Clock/Timer with the ATSTCS Control Station to the appropriate

terminals of the Digital Clock/Timer See wiring detail on next page.

Chassis ground MUST be connected to conduit/Earth ground to provide proper protection from electric shock.

CAUTION: Electric Shock Hazard! When making installation, route eld wiring away from sharp projections, corners, and

internal components.

Apply power to the circuit and conrm correct operation.

Figure 1

Figure 2

6-32 x 3/4black screw

secures device to the

mounting plate

Single or double gang

box (supplied by others)

must be securely mounted

Mounting plate

fastens to the

back box

Mounting plate detail

DSY261RSxE Owner's Manual

AppendixMaintenance

Code Blue

OperationInstallationDescription

Control Station Installation

The ATSTCS Control Station can be mounted to a double gang box, 11/2inch deep or deeper. The Control Station can be

mounted up to 30 feet away from the Digital Clock/Timer. The recommended minimum interconnecting eld wire size is

#22.8 AWG stranded wire. Ensure that installation conforms to the National Electrical Code and local wiring codes.

CAUTION: Electric Shock Hazard! Ensure that no electrical power is present on any wire before installation.

uPull interconnecting eld wires into the double gang box.

vConnect eld wiring interconnecting the ATSTCS Control Station with the Digital Clock/Timer to the

appropriate wires of the Control Station. See wiring detail below.

wMount the Control Station to the double gang box using the machine screws provided.

K2+

K2–

K1+

K1–

12VAC

UNREG

GND

PIEZO

NOT USED

RED

BLACK

VIOLET

GREY

BROWN

BLUE

ORANGE

YELLOW

GREEN

WHITE

PIEZO

BUZZER

RESET

ENTER

START/STOP

INCREMENT

CLOCK

DOWN

SET

RUN

Green-Earth Gnd

Red-Optional

correction line

White-Neutral line

Black-Hot line

Digital Clock/Timer

ATSTCS Control Station

20 ft. supplied cable. Can

be extended to 30 ft.

maximum using #22 AWG

wire (min.) with 1/32”

insulation (min.)

Typical wiring for the Digital Clock/Timer with Control Station

DSY261RSxE Owner's Manual

Appendix Maintenance

Code Blue

Operation Installation Description

Operation

Powering Up

Before applying power, place the SET/RUN switch to the RUN position and the UP/DOWN/CLOCK switch to the CLOCK position.

Apply power to the unit. The displays may rotate during the power on self test and then a version number will appear for a few

seconds. The DSY261RSxE will display 1:00:00 and begin keeping time. If the backup battery is not depleted, the self test will

be bypassed and the DSY261RSxE may display a time other than 1:00:00.

Setting Time

With the UP/DOWN/CLOCK switch still in the CLOCK position:

Set the SET/RUN switch to the SET position.

The clock will now prompt for a 12 or 24 hour format. Press the INCREMENT switch until the desired format is shown and then

press ENTER.

The clock will now prompt for time. The hours digits will be ashing. Press the INCREMENT switch until the desired hour is

shown and then press ENTER. The minutes digits will be ashing. Press the INCREMENT switch until the until the desired

minutes are shown and then press ENTER. Press the INCREMENT switch again to set the desired seconds and then press

ENTER.

The display will ash donE. Press the SET/RUN switch back to RUN when you want timekeeping to begin at the time you

entered.

The clock will now keep time as a free running clock or as a slave if connected to a master clock and in 12 hour format..

Setting the Up Counter Preset Time

If you want to use the alarm and hold feature with the UP timer, you will need to set a preset time for the UP timer.

Set the UP/DOWN/CLOCK switch to the UP position.

Set the SET/RUN switch to the SET position. The hours digits will be ashing.

Using the INCREMENT switch, set the desired hours for the preset time, then press ENTER. The minutes digits will now be

ashing.

Set the desired minutes the same way, then press ENTER. The seconds digits will then be ashing.

Set the desired seconds the same way, then press ENTER. The display will then ash donE.

Set the SET/RUN switch back to the RUN position.

Note: A preset of 00:00:00 allows the digital clock/timer to be used as a standard elapsed timer with a maximum elapsed time

of 30:59:59.

Indice

Altri manuali American Time Orologio

American Time

American Time SiteSync IQ Manuale utente

American Time

American Time H004817 Manuale utente

American Time

American Time Global Series Manuale di istruzioni

American Time

American Time DSY261RSAE Manuale utente

American Time

American Time PGE441RFE-W Manuale di istruzioni

American Time

American Time Wi-Fi Battery Analog Clock Manuale di istruzioni

American Time

American Time ALLSYNC IQ MASTER Manuale di istruzioni

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time H004595 Guida all'installazione

American Time

American Time SiteSynq IQ Manuale utente

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time Wi-Fi Clocks Manuale utente

American Time

American Time WN261RSxE Manuale utente

American Time

American Time AllSync IQ ASQMSTR-00X8E Manuale utente

American Time

American Time AllSync Plus Manuale utente

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time SiteSync IQ Istruzioni operative

American Time

American Time SiteSync IQ Manuale utente

American Time

American Time SSIQ Manuale di istruzioni

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time ALLSYNC IQ Manuale di istruzioni

American Time

American Time SQA261RSAEA Manuale utente

Manuali Orologio popolari di altre marche

Silicon Laboratories

Silicon Laboratories SI5324 Manuale utente

Heathkit

Heathkit GC-1005 Manuale utente

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuale utente

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuale utente

ALGE-Timing

ALGE-Timing ASC3 Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Nixie Clock

Nixie Clock Divergence Meter Manuale utente

La Crosse Technology

La Crosse Technology WS-8256-AL Manuale utente

Mini Gadgets

Mini Gadgets MCPro Manuale utente

Casio

Casio TMR-200 Manuale utente

Progetti

Progetti ILTEMPOSTRINGE Manuale

BVItech

BVItech BV-101 Manuale utente

Progetti

Progetti KALIMERO Manuale

La Crosse Technology

La Crosse Technology WT-3141b Manuale

La Crosse Technology

La Crosse Technology W86531 Manuale utente

Sharp

Sharp SPC900 Manuale utente

La Crosse Technology

La Crosse Technology 404-50447 Manuale utente

Datexx

Datexx DF0063 Manuale utente