American Time H004817 Manuale utente

Installation and Operation Manual

Part # H004817

Rev. 3

September 2017

Wi-Fi Clocks

Wi-Fi Installation Manual

Introduction

The Wi-Fi clock(s) should be installed in a secure location protected from:

– Physical damage

– Water, including condensation

– Direct sunlight

– Operation by untrained personnel

Operation of this product in a manner inconsistent with the instructions in the manual may result in damage to

the product and will void the warranty.

American Time

140 3rd Street South, PO Box 707

Dassel, MN 55325-0707

Phone: 800-328-8996

Fax: 800-789-1882

american-time.com

Safety Precautions

Wi-Fi Installation Manual

Table of Contents

Introduction ..................................................................................................................................................................4

Specifications...............................................................................................................................................................5

Installation ................................................................................................................................................................ 6-8

Battery Analog Clocks .............................................................................................................................................6

Electric Analog Clocks .............................................................................................................................................7

Digital Clocks...........................................................................................................................................................8

Button operation .....................................................................................................................................................9 -10

Analog Button Operation .........................................................................................................................................9

Digital Button Operation......................................................................................................................................... 10

Conguration......................................................................................................................................................... 12-18

Limited Access Point Mode ................................................................................................................................... 12

Clock Conguration ............................................................................................................................................... 13

Wi-Fi Conguration ................................................................................................................................................ 14

Administrator Settings............................................................................................................................................ 18

Homing clock (check hand position) ........................................................................................................................... 19

Firmware update ........................................................................................................................................................20

Factory Defaults restore............................................................................................................................................ 21

Troubleshooting ....................................................................................................................................................22-23

Analog Clock .........................................................................................................................................................22

Digital Clock...........................................................................................................................................................23

Appendix A - SNTP Time Servers ............................................................................................................................. 24

Appendix B - Supported Time Zones.......................................................................................................................25

Appendix C - Enterprise Security Conguration .....................................................................................................26

Introduction

Appendix

Troubleshooting

Configuration

Homing Clock

Firmware

Update

Factory Defaults

Restore

Button

Operation

Installation

Specifications

Wi-Fi Installation Manual

Introduction

Wi-Fi is a popular technology that allows an electronic device to exchange data or connect to the internet wirelessly

using radio waves. Wi-Fi and Simple Network Time Protocol (SNTP) are used to make installation and setup as

simple as possible. All you need to do is apply power to your precongured clock in an area where the intended

Wireless Local Area Network (WLAN) signal strength is sufficient.

Each Wi-Fi clock can be factory-congured to receive the precise time signal from your network server. They also

automatically correct for the Daylight Saving Time changes and require little maintenance. Wi-Fi clocks only require

synchronization twice per day using SNTP and create very little network trafc with staggered wake times. The electric

and digital models can be user-selected to synchronize at a desired frequency.

Network

Precongured Wi-Fi Clocks are plug and play on networks with Dynamic Hosting Conguration Protocol (DHCP).

A limited access point mode is also available for clocks that are not precongured at American Time as recommended.

Introduction

Appendix

Troubleshooting

Configuration

Homing Clock

Firmware

Update

Factory Defaults

Restore

Button

Operation

Installation

Specifications

Wi-Fi Installation Manual

Specifications

Optional Product:

Security Bracket (part number varies by size)

Features:

• Supports 2 static IP address SNTP servers for redundancy or Pool domain names

• 802.11n (b/g compatible, 2.4 GHz only)

• Data rates: 72, 65, 58, 43, 29, 22, 14, 7 Mb ps (8 0 2.11n)

54, 48, 36, 24, 18, 12, 9, 6 Mbps (8 02.11g)

11, 5.5, 2, 1 Mbps (8 02.11b)

• Security protocols: WEP, WPA/WPA2 and Enterprise (PEAPv0-MSCHAPv2)

• DHCP or Static IP addressing

• Limited Access point operation for configuration

• Clocks may be precongured (SSID, Passphrase, time zone, time servers) for plug-n-play installation

• Staggered wake times for reduced network load

• Wi-Fi Alliance Radio/FCC/ICES certified

• RoHS Compliant

Wi-Fi Analog Clock Features:

• WLAN time synchronization

• Status LED

• Plug and play installation with no manual adjustments

• ±1 second accuracy

• Battery clocks use six AA lithium batteries (included domestically)

• Electric clocks - 120vac and 24vac

• Plastic case clocks are high-impact resistant with a shatter-resistant polycarbonate crystal

• Metal case clocks are durable steel, with powder-coat nish and convex glass crystal

Wi-Fi Digital Clock Features:

• Super-bright red LED for high readability

• WLAN time synchronization

• Non-glare lens

• Selectable 12 or 24-hour format

• ±1 second accuracy

• Black anodized aluminum frame (except American series digital clocks use steel enclosures)

• Visibility: 1.8 inches=75 ft.; 2.5 inches=150 ft.; 4 inches=250 ft.

Specifications:

Dimensions: Varies by model

Weight: Varies by model

Operating Humidity: 0% to 95%, non-condensing

Operating Temperature: 41˚F to 131˚F

Storage Temperature: 41˚F to 131˚F

Accuracy: ±1 se cond

Introduction

Appendix

Troubleshooting

Configuration

Homing Clock

Firmware

Update

Factory Defaults

Restore

Button

Operation

Installation

Specifications

Wi-Fi Installation Manual

Introduction

wiring

box

Battery Analog Clocks

Before installing verify:

• Dynamic Host Conguration Protocol (DHCP) settings

• Firewall port 123 is open for UDP data

• Good Wi-Fi coverage at intended installation location.

• Red gear locking pin (A) is removed from the movement

1. Adjustments/Conguration via limited access Point mode

If clock was precongured at American Time as recommended, skip to step 2.

Otherwise, refer to Button Operation (pg 9) and Conguration (Limited Access Point mode, pg 12)

to congure clock manually.

2. Apply power to the clock by inserting the barrel plug (C) of the battery pack into the left side of the Wi-Fi

module where the power connection is located.

n Note:If red gear locking pin (A) has not been removed, remove it prior to applying power.

i. Verify the LED (B):

1. Flashes red when power is applied to the clock.

2. Turns solid green within 60 seconds. Signies normal operation and connection.

3. Solid orange indicates a time server connection failure

4. Solid red indicates a failed Wi-Fi connection

ii. Verify the clocks hands begin to spin rapidly within 3 minutes after applying power.

iii. Verify the correct time on the clock within 10 minutes of applying power.

3. Place the clock on the wall using the hanger on the back of the clock or the optional security bracket

(sold separately).

A - Red gear

locking pin

C - Battery pack

power input

B - LED

Analog Clock Installation

Security Bracket

Keyhole Hanger

Introduction

Appendix

Troubleshooting

Configuration

Homing Clock

Firmware

Update

Factory Defaults

Restore

Button

Operation

Installation

Specifications

Wi-Fi Installation Manual

wiring

box

Electric Analog Clocks

Before installing verify:

• Dynamic Host Conguration Protocol (DHCP) settings

• Firewall port 123 is open for UDP data

• Good Wi-Fi coverage at intended installation location.

• Red gear locking pin (A) is removed from the movement

1. Adjustments/Conguration via limited access Point mode

If clock was precongured at American Time as recommended, skip to step 2.

Otherwise, refer to Button Operation (pg 9) and Conguration (Limited Access Point mode, pg 12)

to congure clock manually.

2. Apply power to Wi-Fi module by inserting the barrel plug of the power cord into the left side of the Wi-Fi

module where the power connection is located for the electric clocks. Insert the other end of the power

cord into the appropriate power source.

n Note:If red gear locking pin (A) has not been removed, remove it prior to applying power.

i. Verify the LED (B):

1. Flashes red when power is applied to the clock.

2. Turns solid green within 60 seconds.

3. Solid orange indicates a time server connection failure

4. Solid red indicates a failed Wi-Fi connection

ii. Verify the clocks hands begin to spin rapidly within 3 minutes after applying power.

iii. Verify the correct time on the clock within 10 minutes of applying power.

3. Place the clock on the wall using the hanger on the back of the clock or the optional security bracket

(sold separately).

A - Red gear

locking pin

B - LED

Security Bracket

Keyhole Hanger

Power Source

Analog Clock Installation

Introduction

Appendix

Troubleshooting

Configuration

Homing Clock

Firmware

Update

Factory Defaults

Restore

Button

Operation

Installation

Specifications

Wi-Fi Installation Manual

Introduction

12”

6”

6 1/8”

9 1/8”

CEILING

Digital Clocks

Before installing verify:

• Dynamic Host Conguration Protocol (DHCP) settings

• Firewall port 123 is open for UDP data

• Good Wi-Fi coverage at intended installation location.

Digital Single Display Surface Mounting

CAUTION: Risk of Electrical Shock - Disconnect and lock out power to the electrical box before

installing or servicing the clock.

1. Remove the hanger from the clock by removing

the screw on top of the clock.

2. Mount the hanger on the wall to a single or double gang box.

3. Make electrical connections (black to hot, white to neutral and

green to ground) for the Molex cable (not wired to the clock) to

a non-switched electrical circuit wiring using UL approved wire

nuts. Route eld wiring away from sharp projections and corners.

4. Join the wall and clock Molex together.

5. Mount the clock on the hanger and secure

with the screw removed in Step 1.

6. Remove plastic protector from display face.

7. Apply power to the circuit and conrm correct operation.

Digital 2-Sided Display - Ceiling or Wall Mount

CAUTION: Risk of Electrical Shock - Disconnect and lock out power

to the electrical box before installing or servicing the clock.

1. Make electrical connections (black to hot, white to neutral and green to ground) for the

Molex cable (not wired to the clock) to non-switched electrical circuit wiring using UL

approved wire nuts. Route eld wiring away from sharp projections and corners.

2. Join the wall/ceiling and clock Molex together.

3. Mount the clock to the ceiling (4" box) or wall (single or double gang box).

4. Remove plastic protector from display face.

5. Apply power to the circuit and conrm correct operation.

nNote for Digital Clocks: If the clock displays the following message: Nt-F (network failure) or

tS-F (time server failure), there is a connection failure with the network and time servers.

Digital Clock Installation

Surface mount

12”

4 5/8”

7 5/8”

6 1/8”

Ceiling mount

Wall mount

Introduction

Appendix

Troubleshooting

Configuration

Homing Clock

Firmware

Update

Factory Defaults

Restore

Button

Operation

Installation

Specifications

Wi-Fi Installation Manual

Analog Button Operation

A recessed push button is located in the lower central part of the Wi-Fi module. It can be used to initiate 4

different operations:

1. Conguration (via Limited Access Point). See also, page 12.

2. Clock homing (sending clock hands to 12 O’clock). See also, page 19.

3. Firmware updates (internet access is required). See also, page 20.

4. Factory defaults restore (restores to the conguration

that the clock was shipped). See also, page 21.

Each operation is proceeded by a number of orange ashes. If the button is released after the operational ash count

(see list below) it will attempt the specic operation listed.

Movement for Analog Clocks

Sync Button: This button is not applicable for Wi-Fi products.

Home Button: This button is used to return the clock hands to the 12:00 or

Home position. Can be used to verify if the hands are set in the right position.

Reset Button: This button is not applicable for Wi-Fi products.

Orange LED

Flash Count

Button

Press Duration

Operation LED Indication Description

0 < 1 second

Wi-Fi

Module Sleep OFF Wi-Fi module will immediately go back to sleep

1 1 - 5 seconds Configuration

Flash

GREEN/ORANGE

Wi-Fi Limited Access Point is available for clock and

Wi-Fi conguration (web browser 192.168.240.1)

25-10 seconds Clock Homing

6 seconds RED

5 seconds ORANGE

10 seconds rapid

GREEN flash

Send clock hands to 12 O'clock position then stop

until power is reset

310-15 seconds

Firmware Update

Flash GREEN/

ORANGE/RED Update the rmware from the internet (port 80)

4 15+ seconds

Factory

Defaults Restore

Flash RED/GREEN Reset conguration to factory settings

LED

HOME SYNC

RESET

Introduction

Appendix

Troubleshooting

Configuration

Homing Clock

Firmware

Update

Factory Defaults

Restore

Button

Operation

Installation

Specifications

Wi-Fi Installation Manual

Introduction

Digital Button Operation

Provisioning Clock

60T0SEtU

Scrolling

SEtUP

Press Enter Button

Setting Clock to 12 or 24 Hour Mode

12or SEt

SEt

CANC

SOFt

dONE

Scrolling

12or24 Hr

Scrolling

SEt 12 Hr

Scrolling

SEt 24 Hr

Scrolling

CANCEL

Scrolling

CANCEL

Press Enter Button Press Enter Button

Press Enter Button

Press Increment Button

When Clock is Connected

Press Increment Button

Continue to Software Update

on Following Page

Press Increment Button

Display Software Version

SOFt Press Enter Button SOFt

Scrolling

sOFt UPdAtE

Press Enter Button

Press Increment Button

Fig. 1

Set the clock

into provisioning

mode in which

the settings can

be changed.

Go to the top of the clock case to change settings on the

digital clock. Begin by switching to Set and using the Enter and

Increment buttons as required, referencing the Figures below.

When complete, switch back to the Run position.

Fig. 3

Display the

software version

currently installed.

Fig. 2

Sets the clock

display to a 12

hour or 24 hour

time format.

Run

SetIncrement

Enter

3”

Edge of casing

.95”

SEtU

Scrolling

SEtUP

The buttons on the digital clock can be used for general clock conguration and advanced debug.

Indice

Altri manuali American Time Orologio

American Time

American Time SQA461RSxE Manuale utente

American Time

American Time ALLSYNC IQ MASTER Manuale di istruzioni

American Time

American Time DSY261RSxE Manuale utente

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time SiteSync IQ Manuale utente

American Time

American Time Global Series Manuale di istruzioni

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time SiteSync IQ Istruzioni operative

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time Wi-Fi Battery Analog Clock Manuale di istruzioni

American Time

American Time WN261RSxE Manuale utente

American Time

American Time DSY261RSAE Manuale utente

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time SSIQ Manuale di istruzioni

American Time

American Time SQA261RSAEA Manuale utente

American Time

American Time SiteSynq IQ Manuale utente

American Time

American Time AllSync Plus Manuale utente

American Time

American Time PGE441RFE-W Manuale di istruzioni

American Time

American Time SiteSync IQ Manuale utente

American Time

American Time Wi-Fi Clocks Manuale utente

American Time

American Time H004595 Guida all'installazione

American Time

American Time SiteSync IQ Manuale di istruzioni

American Time

American Time AllSync IQ ASQMSTR-00X8E Manuale utente

American Time

American Time SiteSync IQ Manuale di istruzioni

Manuali Orologio popolari di altre marche

Silicon Laboratories

Silicon Laboratories SI5324 Manuale utente

Heathkit

Heathkit GC-1005 Manuale utente

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Manuale utente

Andrew O'Malley

Andrew O'Malley DOTKLOK Manuale utente

ALGE-Timing

ALGE-Timing ASC3 Manuale utente

Bodet

Bodet Profil 960 Manuale utente

Nixie Clock

Nixie Clock Divergence Meter Manuale utente

La Crosse Technology

La Crosse Technology WS-8256-AL Manuale utente

Mini Gadgets

Mini Gadgets MCPro Manuale utente

Casio

Casio TMR-200 Manuale utente

Progetti

Progetti ILTEMPOSTRINGE Manuale

BVItech

BVItech BV-101 Manuale utente

Progetti

Progetti KALIMERO Manuale

La Crosse Technology

La Crosse Technology WT-3141b Manuale

La Crosse Technology

La Crosse Technology W86531 Manuale utente

Sharp

Sharp SPC900 Manuale utente

La Crosse Technology

La Crosse Technology 404-50447 Manuale utente

Datexx

Datexx DF0063 Manuale utente