Analog Devices DC2630A Manuale utente

DEMO MANUAL DC2630A

Rev. 0

DESCRIPTION

LT3966

I2C Programmable Quad

Monolithic Boost LED Driver

Demonstration circuit 2630A is an I2C programmable

quad channel monolithic boost LED driver featuring the

3966. It drives four separate strings of LEDs (up

to50V) at 125mA when VIN is between 9V and 18V.

DC2630A runs at 2MHz switching frequency. Its four

channels are capable of powering LED strings which can

have different currents, voltages, or dimming ratios. Each

channel can be independently controlled via I2C commu-

nications or analog inputs. DC2630A can be configured to

run in either mode by modifying the ADDR pin settings.

It is protected against output overcurrent, overvoltage

events, and reports open and short LED fault events by

latching an alert pin. In I2C mode, faults can be enabled or

disabled. A DC2026C Linduino

One demonstration circuit

is used to interface with the board by directly connecting

it with a QuikEval™ribbon cable and provided command

line interface code.

The LT3966 has an input voltage range from 3V to 60V.

Each boost channel has an integrated 60V 1.6A low-side

power switch. It has adjustable switching frequency

between 300kHz and 2MHz and can be synchronized to

an external clock source. Additionally, LT3966 can be pro-

grammed to output its own master clock to sync other

devices. The high side PWMTG MOSFET drivers assist

with PWM dimming and fault protection. The LT3966

channels can be configured to operate as a ground-ref-

erenced step-up (boost) LED driver, or as a floating output

LED driver to perform step-down (buck mode) or step-up/

step-down (buck-boost mode) operation.

All registered trademarks and trademarks are the property of their respective owners.

Each channel of the LT3966 can be independently dimmed

by applying a PWM signal or CTRL voltage to the corre-

sponding channel CTRL/PWM pin while operating in non-

I2C mode. In I2C mode, each channel has a maximum of

13bits of PWM dimming resolution and 8 bits of analog

dimming resolution.

Small ceramic input and output capacitors are used to

save space and cost. The open LED overvoltage protection

uses the IC’s constant-voltage regulation loop to regu-

late the output to approximately 57V if the LED string

isopened.

Undervoltage lockout can be adjusted on the circuit with a

few simple resistor choices. The output voltage (overvolt-

age protection) can be adjusted by changing the feedback

resistors for different string voltages. Other components

may need to be changed to accommodate the change in

output voltages as well.

The LT3966 data sheet gives a complete description of

the device, operation and applications information. The

data sheet must be read in conjunction with this demo

manual for DC2630A. The LT3966EUJ is assembled in a

40-lead plastic 6mm × 6mm QFN package with a thermally

enhanced ground.

Design files for this circuit board are available.

DEMO MANUAL DC2630A

Rev. 0

PARAMETER CONDITION MIN TYP MAX UNIT

Input Voltage VIN Range Operating

Transient

9 18

Switching Frequency (fSW) R30 = 47.5kΩ, MPHASE = OFF 2 MHz

ILED1, ILED2, ILED3, ILED4 R3 = R16 = R22 = R26 = 2Ω 125 mA

Open LED Voltage VOUT R4 = R17 = R23 = R27 = 1MΩ

R5 = R18 = R24 = R28 = 21.5kΩ

57 V

Efficiency (100% PWM DC) VIN = 12.0V, fSW = 2MHz, VLED = 50V

ILED1 = ILED2 = ILED3 = ILED4 = 125mA

86.7%

VLED Range R4 = R17 = R23 = R27 = 1MΩ

R5 = R18 = R24 = R28 = 21.5kΩ

40 56 V

I2C Minimum PWM Dimming Frequency R30 = 47.5kΩ, SCL[2:0] = 0b111 244 Hz

VIN Undervoltage Lockout (UVLO) Falling R2 = 499kΩ, R1 = 84.5kΩ 8.5 V

VIN Enable Turn-On (EN) Rising R2 = 499kΩ, R1 = 84.5kΩ 9.7 V

Note: Make sure that the voltage applied to VIN does not

exceed 50V.

HOW TO OPERATE DC2630A IN NON-I2C MODE

The DC2630A is easy to set up to evaluate the perfor-

mance of the LT3966 in non-I2C mode. Refer to Figure1

for proper measurement equipment setup and follow the

procedure below.

1. With power off, connect a string of up to 16 LEDs

between each channel’s LED+and GND turrets.

Connect the EN/UVLO turret to GND to keep the cir-

cuit shut down. With the power off, connect the input

power supply to the VIN and GND terminals.

2. For non-I2C mode operation, set both JP1 and JP2

(ADDR1 and ADDR2) to 0. This address is for non-

I2C mode, and all other settings are for I2C serial

communications mode.

3. Adjust the input power supply voltage between 9V

and 18V and enable its output.

4. Release the EN/UVLO-to-GND connection.

5. Observe the LED string running at the programmed

LED current.

6. To change the brightness with analog dimming in

non-I2C mode, attach an adjustable voltage source

to the corresponding CTRL/PWM turrets and set

the voltage between 0V and 1.5V. See data sheet

fordetails.

7. To change brightness with external PWM dimming

in non-I2C mode, attach a rectangular waveform

with varying duty cycle to the corresponding CTRL/

PWMturrets.

HOW TO OPERATE DC2630A WITH COMMAND LINE

INTERFACE – I2C SERIAL COMMUNICATIONS MODE

The DC2630A works with a Linduino One microcontroller

board (DC2026C) and can be connected to a PC via USB.

This allows DC2630A to be controlled via serial port inter-

face in Arduino IDE. Refer to the DC2026C Demo Manual

for detailed instructions on installing and configuring the

necessary software libraries.

1. Launch Arduino IDE.

2. Connect Linduino to computer via USB.

3. Connect a ribbon cable between the J1 serial

communications connection and a Linduino One

democircuit.

QUICK START PROCEDURE

PERFORMANCE SUMMARY

Specifications are at TA= 25°C

DEMO MANUAL DC2630A

Rev. 0

4. Download the Linduino code and library files from

the DC2630A web page.

5. Upload the code to the connected Linduino

democircuit.

6. With power off, connect a string of up to 16 LEDs

between each channel’s LED+and GND turrets.

Connect the EN/UVLO turret to GND to keep the cir-

cuit shut down. With the power off, connect the input

power supply to the VIN and GND terminals.

7. For I2C serial communications, set JP1 (ADDR1)

to 1 and JP2 (ADDR2) to 1. This is the chosen I2C

address for the DC2630A command line interface.

8. Open up the serial monitor inside Arduino IDE.

9. Turn on 12V power to the VIN and GND pins of

theDC2630A.

10. Use command line interface in serial monitor to eval-

uate the performance of the LT3966 demo circuit.

Figure1. Test Setup Drawing for DC2630A

QUICK START PROCEDURE

DEMO MANUAL DC2630A

Rev. 0

Figure2. DC2630A Input Voltage vs Efficiency – 4× Channels Powering 16 White LEDs Per Channel at 125mA

Figure3. DC2630A PWM Dimming Using I2C Settings for 1250:1 and 500:1 Dimming Ratios

TEST RESULTS

(V)

100

EFFICIENCY (%)

dc2630a F02

1250:1

500:1

244Hz PWM FREQUENCY

1µs/DIV

LED

50mA/DIV

dc2630a F03

DEMO MANUAL DC2630A

Rev. 0

(a) 50% to 100%

Figure4. DC2630A Load Transient Response

(b) 100% to 50%

20µs/DIV

CTRL/PWM

500mV/DIV

LED

50mA/DIV

dc2630a F04b

TEST RESULTS

20µs/DIV

CTRL/PWM

500mV/DIV

LED

50mA/DIV

dc2630a F04a

DEMO MANUAL DC2630A

Rev. 0

ITEM QTY REFERENCE PART DESCRIPTION MANUFACTURER/PART NUMBER

Required Circuit Components

1 8 C1, C2, C7, C8, C11, C12, C15, C16 CAP., X7R, 2.2µF, 50V, 10% 1206 AVX, 12065C225KAT2A

2 8 C4, C5, C9, C10, C13, C14, C17, C18 CAP., X7R, 2.2µF, 100V, 10% 1206 AVX, 12061C225KAT4A

3 1 C6 CAP., X5R, 4.7µF, 16V, 10% 0603 MURATA, GRM188R61C475KAAJD

4 1 C24 CAP., X7R, 1.0µF, 50V, 10% 0603 TAIYO YUDEN, UMK107AB7105KA-T

5 4 D1, D3, D5, D7 SCHOTTKY DIODES, PMEG6010CEH, SOD-123 NXP, PMEG6010CEH

6 4 L1, L2, L3, L4 IND., 10µH WURTH ELEKTRONIK, 74438336100

7 4 R3, R16, R22, R26 RES., 2Ω, 1/2W, 1% 1206 SUSUMU, RL1632R-2R00-F

8 4 R4, R17, R23, R27 RES., 1M, 1/10W, 1% 0603 VISHAY, CRCW06031M00FKEA

9 4 R5, R18, R24, R28 RES., 22.6k, 1/10W, 1% 0603 VISHAY, CRCW060322K6FKEA

10 1 R30 RES., 47.5k, 1/10W, 1% 0603 VISHAY, CRCW060347K5FKEA

11 1 U1 IC., LT3966, QFN-40, 6mm × 6mm ANALOG DEVICES., LT3966EUJ#PBF

Additional Demo Board Components

1 1 C3 CAP., ALUM., 47µF, 50V, 6.3×7.7 SIZE WURTH ELEKTRONIK, 865080645012

2 0 C20–C23(OPT) CAP., OPTION, 0603

3 4 M1, M2, M3, M4 P-MOSFET, 60V, SOT-23 VISHAY, Si2309CDS-T1-GE3

4 1 R1 RES., 84.5k, 1/10W, 1% 0603 VISHAY, CRCW060384K5FKEA

5 1 R2 RES., 499k, 1/10W, 1% 0603 VISHAY, CRCW0603499KFKEA

6 0 R6, R7, R12, R13, R14, R15, R19,

R20, R21, R25, R31, R33, R34

RES., OPTION, 0603

7 5 R8, R9, R10, R11, R29 RES., 100k, 1/10W, 1% 0603 VISHAY, CRCW0603100KFKEA

Hardware: For Demo Board Only

1 8 E3, E4, E8, E11, E16, E17, E18, E20 TESTPOINT, TURRET, .094" PBF MILL-MAX, 2501-2-00-80-00-00-07-0

2 13 E1, E2, E5, E6, E7, E9, E10, E12, E13,

E14, E15, E19, E21

TESTPOINT, TURRET, .061" PBF MILL-MAX, 2308-2-00-80-00-00-07-0

3 2 JP1, JP2 HEADER 3-PIN 0.079 DOUBLE ROW WURTH ELEKTRONIK, 62000621121

4 2 XJP1 ,XJP2 SHUNT, .079" CENTER WURTH ELEKTRONIK, 60800213421

5 1 J1 HEADER, 2×7 DUAL ROW MOLEX, 87831-1420

6 2 J2, J3 JACK BANANA KEYSTONE, 575-4

7 4 MH1–MH4 STAND-OFF, NYLON 6.4mm WURTH ELEKTRONIK, 702931000

PARTS LIST

DEMO MANUAL DC2630A

Rev. 0

Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog

Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications

subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

SCL

SDA

NOTES: UNLESS OTHERWISE SPECIFIED.

1. ALL CAPACITORS AND RESISTORS ARE 0603.

FLOAT

ADDR1

ADDR2

(36V TRANSIENT)

VIN

FB1

VIN

VOUT1

FB2

FB3

FB4

VIN

VOUT2

VIN

VOUT3

VIN

VOUT4

J29V - 18V

VIN

C20

OPT

PMEG6010CEH

10uH

74438336100

Si2309CDS



GND

E20

R7 OPT

GND

C24

1uF

50V

V+

GND

MISO

5MOSI/SDA

EESDA

EESCL

GND

SCK/SCL

4CS

GND

EEVCC

EEGND

GPIO

2.2uF

1206

50V

JP1

LED4+

E18 125mA

50VLED

R18

22.6K

10uH

74438336100

GND

E17

C15

2.2uF

1206

50V

C10

2.2uF

1206

100V

CTRL/PWM3 E12

R19 OPT

C21

OPT

C11

2.2uF

1206

50V

R30

47.5K

2MHz

LED3+

E16 125mA

50VLED

2.2uF

1206

50V

2.2uF

1206

100V

EXT2 E15

R12

OPT

R11

100k

1206

GND

E11

10uH

74438336100

PMEG6010CEH

100k

INTVCC E7

22.6K

R28

22.6K

2.2uF

1206

50V

R15

OPT

TP2

PMEG6010CEH

GND

E21

R24

22.6K

R26

1206

SYNC E6

2.2uF

1206

100V

CTRL/PWM2 E10

R34

OPT

C17

2.2uF

1206

100V

ALERT

E19

R17

C18

2.2uF

1206

100V

R21 OPT

R22

1206

EXT1 E14

47uF

50V

865080645012

R10

100k

2.2uF

1206

100V

GND E2

R13

OPT

Si2309CDS





4.7uF

R33

OPT

R29

100k

R20 OPT

R31 OPT

C14

2.2uF

1206

100V

C16

2.2uF

1206

50V

CTRL/PWM1 E9

Si2309CDS





EN/UVLO E5

C23

OPT

10uH

74438336100

R16

1206

C12

2.2uF

1206

50V

VIN E1

R27

R14

OPT

CTRL/PWM4 E13

100k

C13

2.2uF

1206

100V

499k

PMEG6010CEH

TP1

JP2

2.2uF

1206

50V

R6 OPT

R25 OPT

LED1+

E3 125mA

50VLED

84.5k

C22

OPT

LT3966EUJ

TG1 2

TG2 29

TG3 7

TG4 24

ISP11

ISP230

ISP38

ISP423

SW1 3

SW2 28

SW3 6

SW4 26

SW4 25

SW3 5

SW1 4

ISN1 40

ISN2 31

ISN3 9

ISN4 22

SW2 27

VIN

FB1 39

FB2 32

FB3 10

FB4 21

CTRL/PWM1

CTRL/PWM2

CTRL/PWM3

CTRL/PWM4

EXT1

EXT2

ADDR1

ADDR2

SDA 18

SCL 19

ALERT

EN/UVLO

INTVCC

SYNC

GND

LED2+

E8 125mA

50VLED

GND

Si2309CDS





R23

ALERT

SCL

INTVCC

SDA

ALERT

INTVCC

SCHEMATIC DIAGRAM

DEMO MANUAL DC2630A

Rev. 0

 ANALOG DEVICES, INC. 2020

10/20

www.analog.com

ESD Caution

ESD (electrostatic discharge) sensitive device. Charged devices and circuit boards can discharge without detection. Although this product features patented or proprietary protection

circuitry, damage may occur on devices subjected to high energy ESD. Therefore, proper ESD precautions should be taken to avoid performance degradation or loss of functionality.

Legal Terms and Conditions

By using the evaluation board discussed herein (together with any tools, components documentation or support materials, the “Evaluation Board”), you are agreeing to be bound by the terms and

conditions set forth below (“Agreement”) unless you have purchased the Evaluation Board, in which case the Analog Devices Standard Terms and Conditions of Sale shall govern. Do not use the Evaluation

Board until you have read and agreed to the Agreement. Your use of the Evaluation Board shall signify your acceptance of the Agreement. This Agreement is made by and between you (“Customer”)

and Analog Devices, Inc. (“ADI”), with its principal place of business at One Technology Way, Norwood, MA 02062, USA. Subject to the terms and conditions of the Agreement, ADI hereby grants to

Customer a free, limited, personal, temporary, non-exclusive, non-sublicensable, non-transferable license to use the Evaluation Board FOR EVALUATION PURPOSES ONLY. Customer understands and

agrees that the Evaluation Board is provided for the sole and exclusive purpose referenced above, and agrees not to use the Evaluation Board for any other purpose. Furthermore, the license granted

is expressly made subject to the following additional limitations:Customer shall not (i) rent, lease, display, sell, transfer, assign, sublicense, or distribute the Evaluation Board;and (ii) permit any Third

Party to access the Evaluation Board. As used herein, the term “Third Party”includes any entity other than ADI, Customer, their employees, affiliates and in-house consultants. The Evaluation Board is

NOT sold to Customer;all rights not expressly granted herein, including ownership of the Evaluation Board, are reserved by ADI. CONFIDENTIALITY. This Agreement and the Evaluation Board shall all

be considered the confidential and proprietary information of ADI. Customer may not disclose or transfer any portion of the Evaluation Board to any other party for any reason. Upon discontinuation of

use of the Evaluation Board or termination of this Agreement, Customer agrees to promptly return the Evaluation Board to ADI. ADDITIONAL RESTRICTIONS. Customer may not disassemble, decompile

or reverse engineer chips on the Evaluation Board. Customer shall inform ADI of any occurred damages or any modifications or alterations it makes to the Evaluation Board, including but not limited

to soldering or any other activity that affects the material content of the Evaluation Board. Modifications to the Evaluation Board must comply with applicable law, including but not limited to the RoHS

Directive. TERMINATION. ADI may terminate this Agreement at any time upon giving written notice to Customer. Customer agrees to return to ADI the Evaluation Board at that time. LIMITATION OF

LIABILITY. THE EVALUATION BOARD PROVIDED HEREUNDER IS PROVIDED “AS IS”AND ADI MAKES NO WARRANTIES OR REPRESENTATIONS OF ANY KIND WITH RESPECT TO IT. ADI SPECIFICALLY

DISCLAIMS ANY REPRESENTATIONS, ENDORSEMENTS, GUARANTEES, OR WARRANTIES, EXPRESS OR IMPLIED, RELATED TO THE EVALUATION BOARD INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTY OF MERCHANTABILITY, TITLE, FITNESS FOR A PARTICULAR PURPOSE OR NONINFRINGEMENT OF INTELLECTUAL PROPERTY RIGHTS. IN NO EVENT WILL ADI AND ITS

LICENSORS BE LIABLE FOR ANY INCIDENTAL, SPECIAL, INDIRECT, OR CONSEQUENTIAL DAMAGES RESULTING FROM CUSTOMER’S POSSESSION OR USE OF THE EVALUATION BOARD, INCLUDING

BUT NOT LIMITED TO LOST PROFITS, DELAY COSTS, LABOR COSTS OR LOSS OF GOODWILL. ADI’S TOTAL LIABILITY FROM ANY AND ALL CAUSES SHALL BE LIMITED TO THE AMOUNT OF ONE

HUNDRED US DOLLARS ($100.00). EXPORT. Customer agrees that it will not directly or indirectly export the Evaluation Board to another country, and that it will comply with all applicable United States

federal laws and regulations relating to exports. GOVERNING LAW. This Agreement shall be governed by and construed in accordance with the substantive laws of the Commonwealth of Massachusetts

(excluding conflict of law rules). Any legal action regarding this Agreement will be heard in the state or federal courts having jurisdiction in Suffolk County, Massachusetts, and Customer hereby submits

to the personal jurisdiction and venue of such courts. The United Nations Convention on Contracts for the International Sale of Goods shall not apply to this Agreement and is expressly disclaimed.

Indice

Altri manuali Analog Devices Scheda madre

Analog Devices

Analog Devices ADP5055-EVALZ Manuale utente

Analog Devices

Analog Devices EVAL-ADN4651EB1Z Manuale utente

Analog Devices

Analog Devices ADRF5519-EVALZ Manuale utente

Analog Devices

Analog Devices AD9551 Manuale utente

Analog Devices

Analog Devices EVAL-ADXRS450Z-V Manuale utente

Analog Devices

Analog Devices EV-ADUCRF101 Manuale utente

Analog Devices

Analog Devices EVAL-ADF4108EBZ1 Manuale utente

Analog Devices

Analog Devices ADuC7024 Manuale utente

Analog Devices

Analog Devices EVAL-MAX49918 Manuale utente

Analog Devices

Analog Devices AD9152-FMC-EBZ Manuale utente

Analog Devices

Analog Devices ADAU1772 Manuale utente

Analog Devices

Analog Devices UG-059 Manuale utente

Analog Devices

Analog Devices UG-082 Manuale utente

Analog Devices

Analog Devices PulSAR AD7685 Manuale utente

Analog Devices

Analog Devices EVAL-CN-304-SDZ Manuale utente

Analog Devices

Analog Devices ADZS-21569-EZKIT Manuale utente

Analog Devices

Analog Devices LTM4626 Guida rapida alla configurazione

Analog Devices

Analog Devices EV-ADF4356SD1Z Manuale utente

Analog Devices

Analog Devices ADZS-AD2428MINI Manuale utente

Analog Devices

Analog Devices EZ-Extender Audio EI3 Manuale utente

Analog Devices

Analog Devices EVAL-ADXL362Z Manuale utente

Analog Devices

Analog Devices EV-ADF5355SD1Z Manuale utente

Analog Devices

Analog Devices EVAL-AD4111SDZ Manuale utente

Analog Devices

Analog Devices AD9361 Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente