Anritsu MP1570A Manuale utente

The test & measurement

equipment you need at

the price you want.

Alltest carries the world’s largest selection of

used/refurbished benchtop test & measurement

equipment at 50% the price of new.

Our equipment is guaranteed working, warrantied, and

available with certified calibration from our in-house staff

of technicians and engineers.

• 10+ full time technicians with over 150 years of

specialization

• 90 day warranty & 5 day right of return on all

equipment

•

• 1-3 year warranties for new and

premium-refurbished equipment

• Every unit tested to OEM specifications

• Satisfaction guaranteed

You have plans, we will help you achieve them.

Any project. Any budget.

Get a quote today!

CCall (732) 919-3339 or email sales@alltest.net.

Alltest Instruments, Inc.

500 Central Ave.

Farmingdale, NJ 07727

P: (732) 919-3339

F: (732) 919-3332

alltest.net

sales@alltest.net

Document No.: M-W1720AE-15.0

ANRITSU CORPORATION

MP1570A

SONET/SDH/PDH/ATM Analyzer

Operation Manual

Vol.1

Basic Operation SONET

For safety and warning information, please read this

manual before attempting to use the equipment.

Keep this manual with the equipment.

15th Edition

Safety Symbols

To prevent the risk of personal injury or loss related to equipment malfunction, Anritsu Corporation uses the following

safety symbols to indicate safety-related information. Ensure that you clearly understand the meanings of the

symbols BEFORE using the equipment. Some or all of the following symbols may be used on all Anritsu

equipment. In addition, there may be other labels attached to products that are not shown in the diagrams in this

manual.

Symbols used in manual

This indicates a very dangerous procedure that could result in serious injury or

death if not performed properly.

This indicates a hazardous procedure that could result in serious injury or death if

not performed properly.

This indicates a hazardous procedure or danger that could result in light-to-severe

injury, or loss related to equipment malfunction, if proper precautions are not taken.

Safety Symbols Used on Equipment and in Manual

The following safety symbols are used inside or on the equipment near operation locations to provide information

about safety items and operation precautions. Ensure that you clearly understand the meanings of the symbols

and take the necessary precautions BEFORE using the equipment.

This indicates a prohibited operation. The prohibited operation is indicated

symbolically in or near the barred circle.

This indicates an obligatory safety precaution. The obligatory operation is

indicated symbolically in or near the circle.

This indicates a warning or caution. The contents are indicated symbolically in or

near the triangle.

This indicates a note. The contents are described in the box.

These indicate that the marked part should be recycled.

MP1570A

SONET/SDH/PDH/ATM Analyzer

Operation Manual Vol.1 Basic Operation SONET Edition

21 February 2000 (First Edition)

14 December 2007 (15th Edition)

publisher.

The contents of this manual may be changed without prior notice.

Printed in Japan

DANGER

WARNING

CAUTION

For Safety

iii

WARNING

1. ALWAYS refer to the operation manual when working near locations

at which the alert mark shown on the left is attached. If the advice in

the operation manual is not followed there is a risk of personal injury

or reduced equipment performance. The alert mark shown on the

left may also be used with other marks and descriptions to indicate

other dangers.

2. IEC 61010 Standard

The IEC 61010 standard specifies four categories to ensure that an

instrument is used only at locations where it is safe to make

measurements. This instrument is designed for measurement

category I (CAT I). DO NOT use this instrument at locations

specified as category II, III, or IV as defined below.

Measurement category I (CAT I):

Secondary circuits of a device that is not directly connected to a

power outlet.

Measurement category II (CAT II):

Primary circuits of a device that is directly connected to a power outlet,

e.g., portable tools or home appliance.

Measurement category III (CAT III):

Primary circuits of a device (fixed equipment) to which power is

supplied directly from the distribution panel, and circuits running from

the distribution panel to power outlet.

Measurement category IV (CAT IV):

Building service-line entrance circuits, and circuits running from the

service-line entrance to the meter or primary circuit breaker

(distribution panel).

For Safety

WARNING

3. Laser radiation warning

•NEVER look directly into the cable connector on the equipment

nor into the end of a cable connected to the equipment. There is

a risk of injury if laser radiation enters the eye.

•The Laser Safety label is attached to the equipment for safety use

as indicated in "Laser Safety" later in this section.

4. To ensure that the instrument is earthed, always use the supplied 3-

pin power cord, and insert the plug into an outlet with an earth

terminal. If power is supplied without earthing the equipment, there

is a risk of receiving a severe or fatal electric shock or causing

damage to the internal components.

5. This equipment cannot be repaired by the operator. DO NOT attempt

to remove the equipment covers or unit covers or to disassemble

internal components. Only qualified service personnel with a

knowledge of electrical fire and shock hazards should service this

equipment. There are high-voltage parts in this equipment presenting

a risk of severe injury or fatal electric shock to untrained personnel. In

addition, there is a risk of damage to precision components.

6. The performance-guarantee seal verifies the integrity of the equipment.

To ensure the continued integrity of the equipment, only Anritsu service

personnel, or service personnel of an Anritsu sales representative,

should break this seal to repair or calibrate the equipment. If the

performance-guarantee seal is broken by you or a third party, the

performance of the equipment cannot be guaranteed. Be careful not

to break the seal by opening the equipment or unit covers.

7. This equipment should always be positioned in the correct manner.

If the cabinet is turned on its side, etc., it will be unstable and may be

damaged if it falls over as a result of receiving a slight mechanical

shock.

Always set up the equipment in a position where the power switch

can be reached without difficulty.

Repair

Falling Over

Electric Shock

Calibration

For Safety

WARNING

8. DO NOT short the battery terminals and never attempt to disassemble

the battery or dispose of it in a fire. If the battery is damaged by any of

these actions, the battery fluid may leak. This fluid is poisonous.

DO NOT touch the battery fluid, ingest it, or get in your eyes. If it is

accidentally ingested, spit it out immediately, rinse your mouth with

water and seek medical help. If it enters your eyes accidentally, do

not rub your eyes, rinse them with clean running water and seek

medical help. If the liquid gets on your skin or clothes, wash it off

carefully and thoroughly.

9. This instrument uses a Liquid Crystal Display (LCD). DO NOT subject

the instrument to excessive force or drop it. If the LCD is subjected to

strong mechanical shock, it may break and liquid may leak.

This liquid is very caustic and poisonous.

DO NOT touch it, ingest it, or get in your eyes. If it is ingested

accidentally, spit it out immediately, rinse your mouth with water and

seek medical help. If it enters your eyes accidentally, do not rub

your eyes, rinse them with clean running water and seek medical help.

If the liquid gets on your skin or clothes, wash it off carefully and

thoroughly.

Battery Fluid

LCD

For Safety

CAUTION

1. Always remove the mains power cable from the power outlet before

replacing blown fuses. There is a risk of electric shock if fuses are

replaced with the power cable connected. Always use new fuses of

the type and rating specified on the rear panel of the instrument.

There is a risk of fire if a fuse of a different rating is used.

10A indicate a normal fusing type fuse.

2. Keep the power supply and cooling fan free of dust.

•Clean the power inlet regularly. If dust accumulates around the

power pins, there is a risk of fire.

•Keep the cooling fan clean so that the ventilation holes are not

obstructed. If the ventilation is obstructed, the cabinet may

overheat and catch fire.

3. The maximum input levels of the optical signal are 0 dBm for

MU150002A 10G input, −8 dBm for MU150002A Option 01 2.5G

input, and +3 dBm for MU150017A/B input. Excessive input level

can damage the internal devices and circuit.

Before performing a self loop-back test, always install 15 dB (when

MP0127A/MP0128A/MP0129A or MU150008A/MU150009A/

MU150010A installed), 10 dB (when MU150002A installed), or 5 dB

(when MU150017A/B installed) attenuator between the output

connector and the input connector.

Fuse Replacement

Cleaning

Check Terminal

For Safety

vii

Class 1, 1M indicate the danger degree of the laser radiation specified

below according to IEC 60825-1:2001.

Class 1: Lasers that are safe under reasonably foreseeable conditions

of operation, including the use of optical instruments for

intrabeam viewing.

Class 1M: Lasers emitting in the wavelength range from 302.5 to 4000

nm that are safe under reasonably foreseeable conditions of

operation, but may be hazardous if the user employs optics

within the beam. Two conditions apply:

a) for diverging beams, if the user views the laser output with

certain optical instruments (for example, eye loupes,

magnifiers and microscopes) within a distance of 100 mm;

b) for collimated beams, if the user views the laser output with

certain optical instruments (for example, telescopes and

binoculars).

For Safety

viii

Class I, IIa, II, IIIa, IIIb indicate the degree of danger of the laser radiation

outlined below as defined by 21 CFR 1040.10:1995.

Class I: Class I levels of laser radiation are not considered to be

hazardous.

Class IIa: Class IIa levels of laser radiation are not considered to be

hazardous if viewed for any period of time less than or equal

to 1×103seconds but are considered to be a chronic viewing

hazard for any period of time greater than 1×103seconds.

The wavelength range of laser radiating is in 400 to 710 nm.

Class II: Class II levels of laser radiation are considered to be a chronic

viewing hazard. The wavelength range of laser radiating is

in 400 to 710 nm.

Class IIIa: Class IIIa levels of laser radiation are considered to be,

depending upon the irradiance, either an acute intrabeam

viewing hazard or chronic viewing hazard, and an acute

viewing hazard if viewed directly with optical instruments.

The wavelength range of laser radiating is in 400 to 710 nm.

Class IIIb: Class IIIb levels of laser radiation are considered to be an

acute hazard to skin and eyes from direct radiation.

CAUTION

Use of controls or adjustments or performance of procedures other than

those specified herein may result in hazardous radiation exposure.

The use of optical instruments with this product will increase eye hazard.

For Safety

WARNING

Before using this instrument, always ensure that the warning light is lit

when the optical output switch is turned on.

If this warning light does not turn on, the equipment may be faulty and for

safety reasons should be returned to an Anritsu service center or

representative for repair.

The laser in the plug-in unit provided for this equipment is classified as

Class 1, 1M according to the IEC 60825-1:2001 standard, or as Class I,

IIIb according to the 21 CFR 1040.10:1995 standard.

Never use optical instruments to directly view Class 1M laser products.

Doing so may result in serious damage to the eyes.

Table 1 Laser Safety Classifications Based on IEC 60825-1:2001

Model Name Class Max. Optical

Output Power (W)*

Pulse Width (s)/

Repetition Rate

Emitted

Wavelength (nm) Laser Aperture

MP0111A 1 0.32 CW 1310 Fig. 1 [1]

MP0112A 1 1 CW 1550 Fig. 1 [2]

0.32 CW 1310 Fig. 1 [1]

MP0113A 1 1 CW 1550 Fig. 1 [2]

MP0122B 1 0.32 CW 1310 Fig. 2, 3 [1]

MP0127A 1 0.84 CW 1310 Fig. 4, 5 [1]

MP0128A 1 0.84 CW 1550 Fig. 4, 5 [1]

0.84 CW 1310 Fig. 4, 5 [1]

MP0129A 1 0.84 CW 1550 Fig. 4, 5 [1]

MU150001A/B 1 0.84 CW 1550 Fig. 6, 7 [1]

MU150001A/B-01/03 1 0.84 CW 1550 Fig. 6, 7 [1]

MU150001A/B-02/03 1 0.84 CW 1310 Fig. 6, 7 [1]

MU150008A 1 0.84 CW 1310 Fig. 4, 5 [1]

MU150009A 1 0.84 CW 1550 Fig. 4, 5 [1]

0.84 CW 1310 Fig. 4, 5 [1]

MU150010A 1 0.84 CW 1550 Fig. 4, 5 [1]

MU150031A/C 1 2.75 CW 1550 Fig. 6, 7 [1]

MU150061A/B 1M 3.32 CW 1310 Fig. 6, 7 [1]

*: Indicates the possible optical output power when each and every

reasonably foreseeable single-fault condition is included.

Laser Safety

Altri manuali per MP1570A

Indice

Altri manuali Anritsu Strumento di misura

Anritsu

Anritsu MS2840A-040 Manuale utente

Anritsu

Anritsu 56100A Manuale del proprietario

Anritsu

Anritsu Field Master Pro MS2090A Manuale utente

Anritsu

Anritsu VectorStar ME7838 4 Series Manuale utente

Anritsu

Anritsu 37 D Series Manuale utente

Anritsu

Anritsu MS2711 Manuale utente

Anritsu

Anritsu MS2690A Manuale utente

Anritsu

Anritsu MS2830A Manuale utente

Anritsu

Anritsu ShockLine MS46121A Series Manuale del proprietario

Anritsu

Anritsu Series MS278XB Manuale utente

Anritsu

Anritsu BTS Master Manuale utente

Anritsu

Anritsu MS2722C Manuale utente

Anritsu

Anritsu MS2711A Manuale utente

Anritsu

Anritsu BTS Master MT8221B Manuale utente

Anritsu

Anritsu MP1800A Manuale utente

Anritsu

Anritsu S331E Manuale utente

Anritsu

Anritsu VectorStar ME7838AX Manuale utente

Anritsu

Anritsu MT1810A Manuale utente

Anritsu

Anritsu PowerMaster MA245 A Series Manuale utente

Anritsu

Anritsu Site Master S331D Manuale del proprietario

Anritsu

Anritsu MT1000A Network Master Pro Manuale utente

Anritsu

Anritsu Spectrum Master MS2723B Manuale utente

Anritsu

Anritsu MS2690A Manuale utente

Anritsu

Anritsu Field Master MS2080A Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente