Anritsu MP1900A Series Manuale utente
MP1900A 32 Gbaud PAM4 Solution
Signal Quality Analyzer-R
MP1900A Series
Quick Start Guide
2
Outline
The Signal Quality Analyzer-R MP1900A series features a high-
expandability design with real-time BER measurement using a PAM4
Convert/Decode function, plus sequential PAM4 BER measurements
using an error detector for more efficient inspection of 400GbE
transceivers and devices.
This Quick Start Guide explains use of the MP1900A series to generate
PAM4 signals up to 32 Gbaud, real-time BER measurement using the
32 Gbaud PAM4 Decoder with CTLE G0376A, and sequential PAM4 BER
measurement using the 21G/32Gbit/s SI ED MU195040A.
3
G0375A/G0376A Real-time BER Measurement
4
Outline of G0375A/G0376A 32 Gbaud PAM4 BER Solution
32 Gbaud Power PAM4 Converter
G0375A
32 Gbaud PAM4 Decoder with CTLE
G0376A
DUT
•3.9 Vp-p (differential) PAM4
output
•10Tap Emphasis
•Clean Eye/Low Jitter
•Tr/Tf 14 ps (typ.)
(PAM4 output)
•CTLE 14 GHz, 12 dB
•Clock recovery
(by MU195040A ED)
•High input sensitivity of
40 mV(EH)
•True PAM4 BER
measurement
Supports PAM4 BER Measurements of PRBS31Q Pattern
Loss CH
MP1900A
•Small remote head for
close-in approach to
DUT
•Multi-channel
•Excellent expandability
and PAM4/NRZ support
5
Setup with G0375A and G0376A for PRBS31Q Error Free
32Gbaud Power PAM4 Converter
G0375A
32Gbaud PAM4 Decoder with CTLE
G0376A
32G 2ch SI PPG
MU195020A
(Opt-020, 021, 031)
32G 2ch SI ED
MU195040A
(Opt-020, 022)
CTLE Input
Decoder Input
Signal Quality Analyzer-R
MP1900A
J1741A cable x4
(80 cm, skew <1 ps)
J1728A cable x2 (40 cm, skew <1 ps)
J1728A cable x2 (40 cm, skew <1 ps)
(*1) Cable x2 (skew <1 ps)
(*1) J1728A or lower loss cable
Synthesizer
MU181000B
Jitter Modulation
MU181500B
DUT
J1439A
80 cm, K cable
41KC-6 x4
6
32 Gbaud PAM4 BER Measurement Item List
Model Name Option Qty Remark
G0375A
32Gbaud
Power PAM4 Converter
-
1
G0376A
32Gbaud
PAM4 Decoder with CTLE
-
1
MP1900A
Signal
Quality Analyzer-R
-
1
MU181000B
12.5GHz 4port Synthesizer
-
1
MU181500B
Jitter
Modulation Source
-
1
For
Jitter injection
MU195020A
21G/32G bit/s SI PPG
001,
020, 021,
031
1
MU195040A
21G/32G bit/s SI ED
001,
020, 022
1
41KC
-6
Fixed
Attenuator 6 dB
4
J1439A
Coaxial
Cable (0.8m, K connector)
1
J1728A
Electrical
Length Specified Coaxial
Cable
(0.4m, K connector)
-
(2)
Cable for waveform
monitoring
MX183000A
PAM
Control
PAM
4 Control
1
Standard
software
MX183000A
-
PL001
Jitter
Tolerance Test
1
For
Jitter Tolerance
Test
7
Specifications Tx
G0375A 32Gbaud Power PAM4 Converter + MU195020A 21G/32G bit/s SI PPG
Item Specification Remarks
Number
of Outputs
2
(Data, xData)
AC coupling
Baud Rate
10
to 32.1 Gbaud
Output
Amplitude
0.3 to 1.95
Vp-p (Single-end, typ.)
Data1 input 0.2 to 1.3 Vp
-p and
Data2 input 0.1 to 0.65 Vp
-p
Random Jitter (rms)
200 fs (typ.)
Tr/Tf (20% to 80%)
14 ps (typ.)
Using MU195020A
SI-PPG
Eye Linearity
(RLM)
0.6 to 1 adjustable from level ratio
Number
of Inputs
4 (Data1, xData1, Data2, xData2)
Uses Data3
and J1735A (two for
differential)
at 3 Eye independent
level control
Maximum Input
Amplitude
1.5 Vp
-p (Data1, xData1)
0.75 Vp
-p (Data2, xData2)
In/Out
Connector
K
(female)
8
Specifications Rx
Item Specification Remarks
Decoder
Number of Inputs 2 (Data, xData)
1 (External clock)
K Connector (female)
Baud Rate 10 to 32.1 Gbaud (DFF ON mode)
10 to 28.1 Gbaud (DFF OFF mode)
Uses MU19040A with external clock
Uses CDR of MU195040A-022
Data Input Amplitude 0.4 Vp-p (typ.)
0.5 Vp-p (max.)
Single-ended
Data Input Sensitivity 40 mV (typ.) 28 Gbaud, Per Eye, Eye Height, Single-
ended at E-6
Clock Input Frequency 10 to 32.1 GHz (DFF ON mode) Full-rate clock
Clock Input Amplitude 0.3 to 1.0 Vp-p External Clock Input
Number of Outputs 3 (Data1, Data2, Monitor Data) K Connector (female)
Data Output level 0/–0.3 V (typ.)
Internal DFF Selectable ON/OFF Uses external Clock for D-FF ON mode
CTLE
Number of Inputs 2 (Data, xData) K Connector (female)
Input Amplitude 0.4 V (max.)
CTLE Gain –12 to 0 dB adjustable
CTLE Peak Frequency 14 GHz (typ.)
Number of Outputs 2 (Data, xData) K Connector (female)
G0376A 32Gbaud PAM4 Decoder with CTLE + MU195040A 21G/32G bit/s SI ED
9
Equipment setup(1/2)
Select PAM4 Control from Application Selector of
MX183000A software, and click Start.
Click Search Start. The software
searches for equipment, and
displays the equipment currently
connected in the connected
equipment display area.
10
Equipment setup(2/2)
- Select Jitter, PPG, and ED with unit number from each selection list.
- Select G0375A and G0376A COM port with USB
*Select “None” when Jitter, PPG or ED isn’t used for testing.
- Set External Att value to 6 dB when 6 dB attenuator is used between PPG and
G0375A. (6 dB attenuator is recommended for evaluating SNDR or SNR_ISI.)
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Anritsu Strumento di misura
Anritsu
Anritsu MX269018A Manuale utente
Anritsu
Anritsu MS2830A Manuale utente
Anritsu
Anritsu MP1570A Manuale utente
Anritsu
Anritsu VectorStar ME7848A-0272 Manuale utente
Anritsu
Anritsu VectorStar MS4640A Series Manuale utente
Anritsu
Anritsu MS2665C Manuale utente
Anritsu
Anritsu MT8820A Manuale utente
Anritsu
Anritsu Field Master MS2080A Manuale utente
Anritsu
Anritsu VectorStar ME7838D Manuale utente
Anritsu
Anritsu VectorStar ME7838 4 Series Manuale utente
Anritsu
Anritsu MU104014B Manuale utente
Anritsu
Anritsu Site Master S820D Manuale utente
Anritsu
Anritsu 37 C Series Manuale utente
Anritsu
Anritsu MT8801C Manuale utente
Anritsu
Anritsu LMR Master S412E Manuale utente
Anritsu
Anritsu Power Master MA24507A Manuale utente
Anritsu
Anritsu MS2690A Manuale utente
Anritsu
Anritsu Site Master Manuale utente
Anritsu
Anritsu MT9083B2 Manuale utente
Anritsu
Anritsu MS2690 Manuale utente
