AOpen AX4B-G2 Scheda tecnica

PS/2 Mouse

Connector SPP/EPP/ECP Parallel Port MIDI/Game Port

MIC-In

Line-In

Speaker Out

2 Keyboard

Connector USB Port COM 1 Port COM 2 Port

FAN3 Connecto

CD-IN Connecto

CNR Expansion Slot

IrDA Connecto

Front Panel Connecto

FDD Connecto

Supports 2nd USB Connecto

JP14 CMOS Clear Jumpe

2Mbit Flash ROM

Resetable Fuse

478-pin CPU socket with Voltage and

Frequency Auto-detection that supports

Intel®Pentium®4 1.4~2.4GHz+ CPU

(Northwood and Willamette are supported)

AGP 4x Expansion Slot

(for 1.5V AGP card)

32-bit PCI Expansion Slot x5

CPU Fan Connector with H/W

Monitoring Function

184-pin DIMM Socket x2 supports

DDR266 DDR SDRAM

maximum up to 2 GB

Intel

845D chipset (Brookdale)

2200μF Low ESR Capacitors

ATX Power Connector

Green: AUX-IN Connecto

Red: MODEM-CN Connecto

4-pin 12V. ATX Power Connector

Onboard AC’97 CODEC

Chassis Intrusion Connecto

Front Audio Connecto

WOL Connecto

JP28 Keyboard/Mouse Wakeup

Enable/Disable Jumper

ATA/33/66/100 IDE Connector x2

FAN2 Connector

RJ45 10/100

LAN Jack

(AX4G-B2N only)

Intel 82562ET PHY (For AX4B-G2N only)

This motherboard comes with a 20-pin and 4-pin ATX power connector as shown below. Make sure you plug

in the right direction. We strongly recommend you to insert the 4-pin connector before connecting the 20-pin

connector.

Normal

(

default

)

Clear CMOS

1. JP14 Clear CMOS

Everything you need to boot this

motherboard is included in this

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in the

Bonus Pack CD Disc. Thanks for

the help of saving our earth.

PART NO: 49.89R03.E02 DOC. NO: AX4BG2N-EG-E0207B

You can clear CMOS to restore system default setting. To

clear the CMOS, follow the procedure below.

1. Turn off the system and unplug the AC power.

2. Remove ATX power cable from connector PWR2.

3. Locate JP14 and short pins 2-3 for a few seconds.

4. Return JP14 to its normal setting by shorting pin 1 & pin 2.

5. Connect ATX power cable back to connector PWR2.

Tip: When should I Clear CMOS?

1. Boot fail because of overclocking…

2. Forget password…

3. Troubleshooting…

2. Connecting ATX Power Connector

This Motherboard x1

This Easy Installation Guide x1

80-wire IDE Cable x1

Floppy Disk Drive Cable x1

Bonus Pack CD x1

NORTON AntiVirus CD x1

Registration Card x 1

Pin 1

Ground

12V

Ground

COM

-5

+12

5VSB

PO-O

COM

PS-ON

COM

-12V

+3.3V

COM

+5V

COM

1. Pull up the CPU socket lever and up to

90-degree angle.

2. Locate Pin 1 in the socket and look fo

a (golden) cut edge on the CPU uppe

interface. Match Pin 1 and cut edge.

Then insert the CPU into the socket.

3. Press down the CPU socket lever and

finish CPU installation.

Plug in the CPU fan cable to the 3-pin CPU FAN connector. If you have chassis fan, you

can also plug it on System Fan (FAN2) or FAN3 (AUX Fan) connector.

CPU Ratio 8x, 9x, 10x… 21x, 22x, 23x, 24x

CPU FSB 100 MHz

Northwood CPU CPU Core Frequency FSB Clock System Bus Ratio

Pentium 4 1.6G 1600MHz 100MHz 400MHz 16x

Pentium 4 1.8G 1800MHz 100MHz 400MHz 18x

Pentium 4 2.0G 2000MHz 100MHz 400MHz 20x

Pentium 4 2.2G 2200MHz 100MHz 400MHz 22x

Pentium 4 2.4G 2400MHz 100MHz 400MHz 24x

Willamette CPU CPU Core Frequency FSB Clock System Bus Ratio

Pentium 4 1.5G 1500MHz 100MHz 400MHz 15x

Pentium 4 1.6G 1600MHz 100MHz 400MHz 16x

Pentium 4 1.7G 1700MHz 100MHz 400MHz 17x

Pentium 4 1.8G 1800MHz 100MHz 400MHz 18x

Pentium 4 1.9G 1900MHz 100MHz 400MHz 19x

Pentium 4 2.0G 2000MHz 100MHz 400MHz 20x

5. Setting CPU Voltage & Frequency

Setting CPU Core Voltage

The CPU core voltage will be automatically detected. It is not necessary to set CPU core

voltage.

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency through the

BIOS setup, and no jumpers or switches are needed.

BIOS Setup > Frequency / Voltage Control > CPU Speed Setting

Core Frequency = CPU FSB Clock * CPU Ratio

3. Installing Processor

Note: If you do not match the CPU

socket Pin 1 and CPU cut edge well, it

may damage the CPU.

CPU socket lever

CPU Pin 1 and cut edge

4. Installing CPU & System Fan

This socket supports Micro-FC-PGA2 package CPU, which is the latest CPU package

developed by Intel. Other forms of CPU package are impossible to be fitted in.

Note: Some CPU fans do not

have sensor pin so they cannot

support fan monitoring.

CPU Fan Connector

FAN2 Connector

GND

+12V

SENSOR

FAN3 Connector

Warning: Intel®845D chipset

supports maximum 400MHz

(100MHz*4) system bus and

66MHz AGP clock; higher clock

setting may cause serious

stem dama

Note: Since the latest processor,

Northwood, would detect the

clock ratio automatically, you

may not be able to adjust the

clock ratio in BIOS manually.

GND

+12V

SENSOR

Secondary

Master (3rd)

Secondary

Slave (4th)

Pin 1

Primary

Slave (2nd) Primary

Master (1st)

USBPWR0

USB_FP_P0-

USB_FP_P0+

GND

KEY

USBPWR0

USB_FP_P1-

USB_FP_P1+

GND

USB_FP_OC0

1 2

8. Connecting IDE and Floppy Cables

9. Connecting Front Panel Cable

7. Connect IrDA Connector

The IrDA connector can be configured to support wireless infrared module, with this

module and application software such as Laplink or Windows 95 Direct Cable

Connection, the user can transfer files to or from laptops, notebooks, PDA devices and

printers. This connector supports HPSIR (115.2Kbps, 2 meters) and ASK-IR (56Kbps).

Install the infrared module onto the IrDA connector and enable the infrared function from

BIOS Setup, UART mode select, make sure to have the correct orientation when you plug

in the IrDA connector.

Connect 34-pin floppy cable and 40-pin, 80-wire IDE cable to floppy connector FDD and

IDE connector. Be careful of the pin1 orientation. Wrong orientation may cause system

damage.

Pin 1

ATA 33/66/100

IDE Connector

Attach the power LED, speaker, and reset switch connectors to

the corresponding pins. If you enable “Suspend Mode” item in

BIOS Setup, the ACPI & Power LED will keep flashing while the

system is in suspend mode.

Locate the power switch cable from your ATX housing. It is

2-pin female connector from the housing front panel. Plug this

connector to the soft-power switch connector marked SPWR.

FDD Connector

IDE 1 (Primary)

IDE 2 (Secondary)

6. Support 2nd USB Port

This motherboard provides four USB connectors to connect USB devices, such as mouse,

keyboard, modem, printer, etc. There are two connectors on the PC99 back panel. You

can use proper cable to connect the other USB connector to the back panel or front panel

of chassis.

USB2 Connector

Pin 1

IrDA Connector

Pin 1

Speaker

IDE LED

SPWR

CPI & PWR

LED

Reset

5VSB

SPWR

ACPI LED-

GND

ACPILED

GND

RESET

GND

IDE LED

GND

SPEAKE

KEY

GND

IR_RX

IR_T

Connector Pin1 Pin2 Pin3 Pin4

CD-IN Left GND GND Right

MODEM-CN Mono In GND GND Mic Out

AUX-IN Left GND GND Right

12. Connecting CD / MODEM / AUX Connector

10. Front Audio Connector

If the housing has been designed with an audio port on the front panel, you’ll be able to

connect onboard audio to front panel through this connector. By the way, please remove

5-6 and 9-10 jumper caps from the Front Audio Connector before connecting the cable.

Please do not remove these 5-6 and 9-10 yellow jumper caps if there’s no audio port on

the front

anel.

The AUX-IN connector is used to connect MPEG

Audio cable from MPEG card to onboard sound.

The MODEM-CN connector is used to connect

Mono In/ Mic Out cable from internal modem card to

onboard sound circuit.

The CD-IN connector is used to connect CDAudio

cable from CDROM or DVD drive to onboard sound.

-IN

(

Green

)

CD-IN (Black)

MODEM-CN

(Red)

Pin 1

13. Installing LAN Driver (AX4B-G2N only)

11. Support 10/100 Mbps LAN onboard (AX4B-G2N only)

The South Bridge ICH2 includes a fast Ethernet controller on chip. On the strength of Intel

82562ET PHY on board, which is a highly-integrated Platform LAN Connect device, it

provides 10/100M bps Ethernet for office and home use, the Ethernet RJ45 connector is

located on top of USB connectors. The green LED indicates the link mode, it lights when

linking to network and blinking when transferring data. The orange LED indicates the

transfer mode, and it lights when data is transferring in 100Mbps mode. To enable or

disable this function, you may simply adjust it through BIOS.

Orange/Speed

Green/ACT

You may find Intel’s Intel PRO Network Connections to install the LAN Driver step by step.

AUD_MIC

AUD_MIC_BIAS

AUD_FPOUT_R

AUD_FROUT_L

AUD_GND

AUD_VCC

AUD_RET_R

KEY

AUD_RET_L

9 10

1 2

fter you finish the setting of jumpers and connect correct cables. Power on

and enter the BIOS Setup, press <Del> during POST (Power On Self Test).

Choose "Load Setup Defaults" for recommended optimal performance.

Caution: By updating your motherboard, you are taking a risk of BIOS flash failure.

If your motherboard is working stable, and there are no major bugs that had been

fixed by a latter BIOS revision, we recommend that you DO NOT try to upgrade

your BIOS.

14. Power-on and Load BIOS Setup

15. AOpen Bonus Pack CD

16. Installing Onboard Sound Driver

You can use the autorun menu of Bonus CD disc. Choose the utility and driver and selec

model name.

Del

Warning: Please avoid of using "Load

Turbo Defaults", unless you are sure

our system components (CPU, DRAM,

HDD, etc.) are good enough for turbo

settin

This motherboard comes with AC97 CODEC, you can find the audio driver from the

Bonus Pack CD disc auto-run menu.

17. BIOS Upgrade under Windows Environment

You may accomplish BIOS upgrade procedure with EZWinFlash by the following steps,

and it’s STRONGLY RECOMMMANDED to close all the applications before you start the

upgrading.

1. Download the new version of BIOS package zip file from AOpen official web site. (ex:

http://www.aopen.com)

2. Unzip the download BIOS package (ex: WAX4BG2102.ZIP) with WinZip

(http://www.winzip.com) in Windows environment.

3. Save the unzipped files into a folder, for example, W AX4BG2102.EXE & W

AX4BG2102.BIN.

4. Double click on the W AX4BG2102.EXE, EZWinFlash will detect the model name

and BIOS version of your motherboard. If you had got the wrong BIOS, you will no

be allowed to proceed with the flash steps.

5. You may select preferred language in the main menu, then click [Start Flash] to star

the BIOS upgrade procedure.

6. EZWinFlash will complete all the process automatically, and a dialogue box will pop

up to ask you to restart Windows. You may click [YES] to reboot Windows.

7. Press <Del> at POST to enter BIOS setup, choose "Load Setup Defaults", then

“Save & Exit Setup”. Done!

If you encounter any trouble to boot you system, follow the procedures

accordingly to resolve the problem.

Part Number and Serial Number

The Part Number and Serial number are printed on bar code label. You can find this

bar code label on the outside packing, on ISA/CPU slot or on component side of PCB.

For example:

Model name and BIOS version

AX4B-G2 R1.02 May. 01. 2002 AOpen Inc.

Award Plug and Play BIOS Extension v1.0A

Model name and BIOS version can be found on upper left corner of first boot screen

(POST screen). For example:

AX4B-G2 is model name of motherboard; R1.02 is BIOS version

Make sure if the jumper settings for CPU and DRAMs are correct.

Clear CMOS.

Install the VGA card. Then connect your monitor and keyboard.

The problem was probably caused

by power supply or motherboard

failure. Please contact your reselle

or local distributor for repairing.

Perhaps your VGA card or monito

is defective.

Yes

It is very possible that your keyboard

is defective.

During system rebooting, press Del to enter BIOS Setup. Choose

“Load Setup Default".

The problem should be caused by the

IDE cables or HDD itself.

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Turn off the power and unplug the AC power cable, then remove all

of the addon cards and cables, including VGA, IDE, FDD, COM1,

COM2 and Printer.

Turn on the power, and check if

the power supply and CPU fan

work properly.

Start

Check if there is display.

Press Ctrl, and Alt key at the

same time, hold them and then

press Del to see if the

stem reboots.

Turn off the system and

re-connect the IDE cable.

Check if the system can

reboot successfully.

End

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

Part No. Serial No.

Dear Customer,

Thanks for choosing AOpen products. To provide the best and fastest service to

our customer is our first priority. However, we receive numerous emails and

hone-calls worldwide everyday, it is very hard for us to serve everyone on time.

We recommend you follow the procedures below and seek help before contact

us. With your help, we can then continue to provide the best quality service to

more customers.

Thanks very much for your understanding!

Open Technical Supporting Team

Online Manual: Please check the manual carefully and make sure the

jumper settings and installation procedure are correct.

http://www.aopen.com/tech/download/manual/default.htm

Test Report: We recommend to choose board/card/device from the

compatibility test reports for assembling your PC.

http://www.aopen.com/tech/report/default.htm

FAQ: The latest FAQ (Frequently Asked Questions) may contain a

solution to your problem.

http://www.aopen.com/tech/faq/default.htm

Download Software: Check out this table to get the latest updated

BIOS/utility and drivers.

http://www.aopen.com/tech/download/default.htm

News Group: News posted by computer experts, you are welcome to join

any discussion and learning from it.

http://www.aopen.com/tech/newsgrp/default.htm

Contact Distributors/Resellers: We sell our products through resellers

and integrators. They should know your system configuration very well and

should be able to solve your problem efficiently and provide important

reference for you if next time you want to buy something else from them.

before contacting us. The part number, serial number and BIOS version

are also very helpful.

Web Site: www.aopen.com

E-mail: Send us email by going through the contact form below.

English http://www.aopen.com/tech/contact/techusa.htm

Japanese http://www.aopen.co.jp/tech/contact/techjp.htm

Chinese http://www.aopen.com.tw/tech/contact/techtw.htm

German http://www.aopencom.de/tech/contact/techde.htm

French http://france.aopen.com/tech/contact/techfr.htm

Simplified Chinese http://www.aopen.com.cn/tech/contact/techcn.htm

Pacific Rim

AOpen Inc.

Tel: 886-2-3789-5888

Fax: 886-2-3789-5899

America

AOpen America Inc.

Tel: 1-408-922-2100

Fax: 1-408-922-2935

Europe

AOpen Computer b.v.

Tel: 31-73-645-9516

Fax: 31-73-645-9604

Germany

AOpen Computer GmbH.

Tel: 49-2102-157700

Fax: 49-2102-157799

China

艾艾爾鵬國際貿易(上海)有限

公司

Tel: 86-21-6225-8622

Fax: 86-21-6225-7926

Japan

AOpen Japan Inc.

Tel: 81-048-290-1819

Fax: 81-048-290-1820

Altri manuali per AX4B-G2

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali AOpen Scheda madre

AOpen

AOpen AK33 M Scheda tecnica

AOpen

AOpen DXPS Manuale utente

AOpen

AOpen AX4T II-533 Guida all'installazione

AOpen

AOpen AK77-8X Guida all'installazione

AOpen

AOpen AP43 Manuale utente

AOpen

AOpen AX4G Pro Scheda tecnica

AOpen

AOpen AX34 Pro II Scheda tecnica

AOpen

AOpen DX34-U Manuale utente

AOpen

AOpen AX45F-4D Manuale utente

AOpen

AOpen MX3S-T Guida all'installazione

AOpen

AOpen AX4T 2-533 Scheda tecnica

AOpen

AOpen AK86-L Guida all'installazione

AOpen

AOpen AK86-L Scheda tecnica

AOpen

AOpen AX4B-133 Scheda tecnica

AOpen

AOpen AX6BP Manuale utente

AOpen

AOpen I865Gm-7L/7N Manuale utente

AOpen

AOpen AK79G MAX Manuale utente

AOpen

AOpen AX45F-8X MAX Scheda tecnica

AOpen

AOpen AX4S-U Manuale utente

AOpen

AOpen DXPN-U Manuale utente

AOpen

AOpen I915GAPLF-0410A Manuale utente

AOpen

AOpen MX 36 LE-U Guida all'installazione

AOpen

AOpen AX4SP Guida all'installazione

AOpen

AOpen AX45-8X Max Guida all'installazione

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente