AOpen MX36LE-UI Manuale utente

Onboard AC97 CODEC

MIC-In

PS/2 Mouse

Connector

PS/2 Keyboard

Connector USB Port

SPP/EPP/ECP

Parallel Port

COM 1 Port VGA

Connector

MIDI/Game

Port

Line-In

Speaker

Out

ATX Power Connector

CPU Fan Connector with Hardware Monitoring

Low ESR Capacitor

370-pin CPU Socket Support 66/100/133Mhz

FSB for Intel Pentium!!! Tualatin / Celeron

533MHz~1.2GHz+ and VIAC3 800MHz+

VIA PLE133 Chipset with integrated Trident

Blade3D graphic engine

PC-100/133 DIMM Socket x2

Supports maximum up to 1.0GB

JP23 CPU FSB Select

ATA 33/66/100 IDE Connector x2

FDD Connector

MODEM-CN Connecto

CD-IN Connecto

ISA Expansion Slo

Support 2nd USB Port

Fan2 Connecto

with Hardware Monitoring

RTL8100B LAN Chip

IrDA Connecto

COM2 Port Connecto

2Mbit Flash EEPROM BIOS

32-bit PCI Slot x3

JP14 Clear CMOS

WOL Connecto

Front Audio Connecto

Front Panel Connecto

Resettable Fuse

AUX-IN Connecto

LAN Connector

JP13 L

N Select Jumpe

JP28 Keyboard/Mouse Wakeup Jumper

S/PDIF Connecto

1. Clear CMOS Data

2. Installing CPU

Everything you need to boot this

motherboard is included in this

Easy Installation Guide. For more

information, a complete Online

User's Manual can be found in the

Bonus Pack CD. Thanks for the

help of saving our earth!

PART NO: 49.89Q03.001 DOC. NO: MX36LEUI-EG-E0203A

80-wire IDE Cable x 1

Floppy Drive Cable x 1

Bonus Pack CD x 1

This Easy Installation Guide x 1

Motherboard x 1

Tip: When should I Clear CMOS?

1. Boot fail because of overclocking…

2. Forget password…

3. Troubleshooting…

You can clear CMOS to restore system default setting. To clea

the CMOS, follow the procedure below.

1. Turn off the system and unplug the AC power.

2. RemoveATX power cable from connector PWR2.

3. Locate JP14 and short pins 2-3 for a few seconds.

. Return JP14 to its normal setting by shorting pin 1 and pin 2.

5. ConnectATX power cable back to connector PWR2.

1. Pull up the CPU socket lever and up to

90-degree angle.

2. Locate Pin 1 in the socket and look for a blac

dot or cut edge on the CPU upper interface.

Match Pin 1 and cut edge. Then insert the

CPU into the socket.

3. Press down the CPU socket lever and finish

CPU installation.

Note: If you do not match the CPU

socket Pin 1 and CPU cut edge well,

ou ma

dama

e the CPU.

CPU Pin1 and

cut edge

CPU socket

Lever

Pin 1 Normal

(

default

)

Clear CMOS

This jumper is used to specify the relationship of PCI and FSB clock. Generally speaking, i

you are not an overclocker, we recommend you to set at the default setting.

Plug in the CPU fan cable to the 3-pin CPUFAN connector. If you have a housing fan,

you can also plug it on FAN2 connector.

1 2 1 2 1 2

JP23 FSB Select Jumper

CPU Core Voltage Auto-Detection

This motherboard supports CPU VID function. The CPU core voltage will be automatically

detected. It is not necessary to set CPU Core Voltage.

Setting CPU Frequency

This motherboard is CPU jumper-less design, you can set CPU frequency through the

BIOS setup, and no jumpers or switches are needed.

BIOS Setup > Frequency/Voltage Control > CPU Host Clock (CPU/PCI)

Core Frequency = CPU FSB Clock * CPU Ratio

CPU Ratio 3x, 3.5x, 4x, 4.5x, …16x

CPU FSB 66.8, 75, 83.3, 100, 103, 105, 110, 112, 115, 120, 124, 133, and 150MHz

CPU CPU Core Frequency FSB Clock Ratio

Celeron 533 533MHz 66MHz 8x

Celeron 566 566MHz 66MHz 8.5x

Celeron 600 600MHz 66MHz 9x

Celeron 667 667MHz 66MHz 10x

Celeron 700 700MHz 66MHz 10.5x

Celeron 800 800MHz 100MHz 8x

Celeron 900 900MHz 100MHz 9x

Celeron 1.2G 1.2GHz 100MHz 12x

Pentium III 800E 800MHz 100MHz 8x

Pentium III 850E 850MHz 100MHz 8.5x

Pentium III 533EB 533MHz 133MHz 4x

Pentium III 600EB 600MHz 133MHz 4.5x

Pentium III 667EB 667MHz 133MHz 5x

Pentium III 733EB 733MHz 133MHz 5.5

Pentium III 800EB 800MHz 133MHz 6x

Pentium III 866EB 866MHz 133MHz 6.5

Pentium III 933EB 933MHz 133MHz 7x

Pentium III 1G 1000MHz 133MHz 7.5x

Pentium III 1.13G 1.13GHz 133MHz 8.5x

Pentium III 1.2G 1.2GHz 133MHz 9x

Pentium III 1.3G 1.3GHz 133MHz 10x

5. Setting CPU Voltage & Frequency

4. JP23 Adjust FSB/PCI Clock

3. Installing CPU & Housing Fan

Home Tip: If your system hangs or fails to boot because of overclocking,

simply use <Home> key to restore the default setting.

Warning: VIA PLE133 chipset supports maximum

133MHz FSB, higher clock setting may cause

serious system damage.

Note: Some CPU fans do not have

sensor pin, so that they cannot

support fan monitoring.

CPUFAN

FAN2

FSB Select

FSB=66MHz FSB=100MHz FSB=133MHz Auto

Detection

(Default)

1 2

GND

+12V

SENSOR

Pin 1

7. JP28 Keyboard / Mouse Wakeup Jumper

6. JP13 LAN Select Jumper 8. S/PDIF Connector (Optional)

9. Connecting Front Panel Cable

This motherboard provides keyboard / mouse wake-up function. You can use JP28 to

enable or disable this function, which could resume your system from suspend mode with

keyboard or mouse. The factory default setting is set to “Disable”(1-2), and you ma

enable this function by setting the jumper to 2-3.

S/PDIF (Sony/Philips Digital Interface) is a latest audio transfer file format that provides

impressive quality through optical fiber and allows you to enjoy digital audio instead o

analog. Normally there are two S/PDIF outputs as shown, one for RCA connector, the

most common one used for consumer audio products, and the other for optical connecto

with a even better audio quality. Through a specific audio cable, you can connect the

SPDIF connector to a S/PDIF audio module bearing S/PDIF digital output. However, you

must have a S/PDIF supported speaker with SPDIF digital input to make the most of this

function.

Attach the power LED, ACPI, speaker, power and reset

switch connectors to the corresponding pins. If you enable

“Suspend Mode” item in BIOS Setup, the ACPI & Power

LED will keep flashing while the system is in suspend

mode.

Locate the power switch cable from your ATX housing. It is

2-pin female connector from the housing front panel. Plug

this connector to the soft-power switch connector marked

SPWR.

This jumper allows you to enable or disable the LAN onboard function by adjusting the

position of yellow cap.

Speaker

IDE LED

SPWR

+ACPI &

Power LED

Reset

SPWR

GND

ACPILED-

GND

ACPILED

GND

RESET

GND

IDE LED

GND

SPEAKE

Pin 1

Enable Disable

1 1

Disable

(Default) Enable

Pin1

Pin 1

SPDIF Module

Connecting to

RCA Cable

Connecting to

Optical Cable

Audio cable

After you finish jumper settings and connect correct cables, power on and enter the

BIOS Setup. Press <Del> during POST (Power On Self Test). Choose "Load Setup

Defaults" for recommended optimal performance.

Pin 1

Connector Pin1 Pin2 Pin3 Pin4

CD-IN Left GND GND Right

MODEM-CN Mono In GND GND Mic Out

AUX-IN Left GND GND Right

12. Power-on and Load BIOS Setup

10. Connecting CD / MODEM / AUX-IN

11. Connecting Front Audio Connector

The CD-IN connector is used to connect CD Audio

cable from CDROM or DVD drive to onboard sound.

The MODEM-CN connector is used to connect Mono

In / Mic Out cable from internal modem card to

onboard sound circuit.

The AUX-IN connector is used to connect MPEG

Audio cable from MPEG card to onboard sound.

CD-IN

MODEM-CN

AUX-IN Del

Warning: Please avoid of using

"Load Turbo Defaults", unless you

are sure your system components

(CPU, DRAM, HDD, etc.) are good

enough for turbo setting.

You can install LAN Driver under Windows95/98, Windows NT and Windows 2000 for Realtek

RTL8139 Family (RTL8100 included) PCI Fast Ethernet adapter by following steps.

Installing driver procedure on Microsoft Windows 95 :

-----------------------------------------------------

1. Select "Driver from disk provided by hardware manufacturer" when being asked which driver you

would like to install.

2. Specify the setup file pathname

[CD-ROM]:Driver\LAN\RTL8100\Windows\Win95\WIN95A (for Windows 95 and Win95A) or

[CD-ROM]:Driver\LAN\RTL8100\Windows\Win95 (for Windows 95 OSR2).

3. Follow the procedure and insert Windows 95 system disk to complete setup step.

4. Windows 95 will finish the other installation procedures automatically, and then restart your system.

Installing driver for Win98/Win98 SE/Windows2000/Windows ME :

-------------------------------------------------------------------

1. Select "Driver from disk provided by hardware manufacturer" when being asked which driver you

would like to install.

2. Specify the setup file pathname

[CD-ROM]:Driver\LAN\RTL8100\Windows\WIN98 (for Windows 98/98 SE) or

[CD-ROM]:Driver\LAN\RTL8100\Windows\WIN2000 (for Windows 2000) or

[CD-ROM]:Driver\LAN\RTL8100\Windows\Windows ME (for Windows ME)

3. Follow the procedure and insert your system disk (Win98/Win98 SE/Windows2000/Windows ME) to

complete setup step.

4. Win98/Win98 SE/Windows2000/Windows ME will finish the other installation procedures

automatically, and then restart your system.

13. Installing LAN Driver

If the housing is designed with an audio port on the front panel, you’ll be able to connec

onboard audio to front panel through this connector. Please remove the jumper cap from

the front audio connector before you connect the cable. Do not remove this yello

umper cap if your housing does not have an audio port on the front panel.

Front Audio Connector

FP_MIC

FP_VREF

PHONE_R

PHONE_L

GND

+5V

KEY

1 2

9 10

14. AOpen Bonus Pack CD

15. Installing Onboard AGP Driver 17. BIOS Upgrade

AOpen Easy Flash is user-friendlier than traditional flash method. The BIOS binary file

and flash routine are combined together and you simply run a single file to complete the

flash process.

1. Download new BIOS upgrade zipped file fromAOpen's web site. For example,

MX36LEUI102.ZIP.

2. Run shareware PKUNZIP (http://www.pkware.com/) which supports

miscellaneous operation systems to extract the binary BIOS file and the flash

utility. Or Winzip (http://www.winzip.com/) in Windows environment.

3. Save the unzipped file into a bootable floppy disk.

For example, MX36LEUI102.BIN & MX36LEUI102.EXE

4. Reboot the system to DOS mode without loading any memory handler (such as

EMM386) or device driver. It needs around 520K free memory space.

5. Execute A:> MX36LEUI102 and the program will do the rest of it.

DO NOT turn off the power during FLASH PROCESS until you are asked to!!

6. Reboot system and press <Del> to enter BIOS Setup, Choose "Load Setup

Defaults", then “Save & Exit Setup” and finish the BIOS upgrade.

Warning: The upgrade of new BIOS will permanently replace your original BIOS

content after flashing. The original BIOS setting and Win95/Win98 PnP information

will be refreshed and

robabl

need to re

confi

ure

our s

stem.

16. Installing Onboard Audio Driver

You can use the autorun menu of Bonus CD. Choose the utility and driver and select

model name. This motherboard comes with an AC97 CODEC. You can find the audio driver from the

Bonus Pack CD autorun menu.

VIA PLE133 chipsets integrates a 2D/3D graphics accelerator and provides AGP

2X/4X incredible performance to access main memory at over 1GB/s. You can find the

AGP driver from the autorun menu of Bonus Pack CD.

If you encounter any trouble to boot you system, follow the

procedures accordingly to resolve the problem.

Part Number and Serial Number

The Part Number and Serial number are printed on bar code label. You can find this

bar code label on the outside packing, on ISA/CPU slot or on component side of PCB.

For example:

Model name and BIOS version

MX36LE-UI R1.00 Mar. 01. 2002 AOpen Inc.

Award Plug and Play BIOS Extension v1.0A

Model name and BIOS version can be found on upper left corner of first boot screen

(POST screen). For example:

P/N: 91.88110.201 is part number, S/N: 91949378KN73 is serial number.

MX36LE-UI is the model name of motherboard, R1.00 is BIOS version.

Make sure if the jumper settings for CPU and DRAMs are correct.

Clear CMOS.

Install the VGA card. Then connect your monitor and keyboard.

The problem was probably caused

by power supply or motherboard

failure. Please contact your reselle

or local distributor for repairing.

Perhaps your VGA card or monito

is defective.

Yes

It is very possible that your keyboard

is defective.

During system rebooting, press Del to enter BIOS Setup. Choose

“Load Setup Default".

The problem should be caused by the

IDE cables or HDD itself.

Re-install Windows 95, Windows 98 or Windows NT.

Yes

Turn off the power and unplug the AC power cable, then remove all

of the addon cards and cables, including VGA, IDE, FDD, COM1,

COM2 and Printer.

Turn on the power, and check if

the power supply and CPU fan

work properly.

Start

Check if there is display.

Press Ctrl, and Alt key at the

same time, hold them and then

press Del to see if the

stem reboots.

Turn off the system and

re-connect the IDE cable.

Check if the system can

reboot successfully.

End

Part No. Serial No.

Dear Customer,

Thanks for choosing AOpen products. To provide the best and fastest service to

our customer is our first priority. However, we receive numerous emails and

hone-calls worldwide everyday, it is very hard for us to serve everyone on time.

We recommend you follow the procedures below and seek help before contact

us. With your help, we can then continue to provide the best quality service to

more customers.

Thanks very much for your understanding!

Open Technical Supporting Team

Online Manual: Please check the manual carefully and make sure the

jumper settings and installation procedure are correct.

http://www.aopen.com/tech/download/manual/default.htm

Test Report: We recommend to choose board/card/device from the

compatibility test reports for assembling your PC.

http://www.aopen.com/tech/report/default.htm

FAQ: The latest FAQ (Frequently Asked Questions) may contain a

solution to your problem.

http://www.aopen.com/tech/faq/default.htm

Download Software: Check out this table to get the latest updated

BIOS/utility and drivers.

http://www.aopen.com/tech/download/default.htm

News Group: Your problem probably had been answered by our support

engineer or professional users on the news group.

http://www.aopen.com/tech/newsgrp/default.htm

Contact Distributors/Resellers: We sell our products through resellers

and integrators. They should know your system configuration very well and

should be able to solve your problem more efficiently. After all, it is an

important reference for you if next time you want to buy something else

from them.

before contacting us. The part number, serial number and BIOS version

are also very helpful.

Web Site: www.aopen.com

E-mail: Send us email by going through the contact form below.

English http://www.aopen.com/tech/contact/techusa.htm

Japanese http://www.aopen.co.jp/tech/contact/techjp.htm

Chinese http://www.aopen.com.tw/tech/contact/techtw.htm

German http://www.aopencom.de/tech/contact/techde.htm

French http://france.aopen.com/tech/contact/techfr.htm

Simplified Chinese http://www.aopen.com.cn/tech/contact/techcn.htm

Pacific Rim

AOpen Inc.

Tel: 886-2-3789-5888

Fax: 886-2-3789-5399

America

AOpen America Inc.

Tel: 1-408-922-2100

Fax: 1-408-922-2935

Europe

AOpen Computer b.v.

Tel: 31-73-645-9516

Fax: 31-73-645-9604

Germany

AOpen Computer GmbH.

Tel: 49-2102-157700

Fax: 49-2102-157799

China

艾尔鹏国际上海(股)有限公司

Tel: 86-21-6225-8622

Fax: 86-21-6225-7926

Japan

AOpen Japan Inc.

Tel: 81-048-290-1800

Fax: 81-048-290-1820

Altri manuali per MX36LE-UI

Indice

Altri manuali AOpen Scheda madre

AOpen

AOpen 1AK79G-V Guida all'installazione

AOpen

AOpen AX45F-8X MAX Scheda tecnica

AOpen

AOpen AX6B Plus Manuale utente

AOpen

AOpen i915Gm-PL Scheda tecnica

AOpen

AOpen Manual Manuale utente

AOpen

AOpen AX4SG WLAN Scheda tecnica

AOpen

AOpen AX45-4D MAX Guida all'installazione

AOpen

AOpen DX34-U Manuale utente

AOpen

AOpen AX6BC PROII Manuale utente

AOpen

AOpen MT85 Manuale utente

AOpen

AOpen n250a Manuale utente

AOpen

AOpen MX4SG-4DL Scheda tecnica

AOpen

AOpen AX4C-G Scheda tecnica

AOpen

AOpen n250a-FR Manuale utente

AOpen

AOpen AX4B-533 Plus Guida all'installazione

AOpen

AOpen AK76D Scheda tecnica

AOpen

AOpen AX63 Guida all'installazione

AOpen

AOpen AX4LR Manuale utente

AOpen

AOpen AX4GR Guida all'installazione

AOpen

AOpen AX4SG Max II Manuale utente

AOpen

AOpen AX45H-8X Max Scheda tecnica

AOpen

AOpen AK77-600GN Scheda tecnica

AOpen

AOpen s760GXm-SL Manuale utente

AOpen

AOpen AX34-U Scheda tecnica

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente