Apera Instruments SX721 Manuale utente

- 1 -

SX721 Portable pH/ORP Meter

User Manual

APERA Instruments (Europe) GmbH

aperainst.de

- 2 -

Table of Contents

1Brief Instruction...............................................................................................................- 3 -

2Technical Specifications....................................................................................................- 3 -

3About the Meter.............................................................................................................. - 4 -

4What’s in the kit ..............................................................................................................- 6 -

5Preparation .....................................................................................................................- 6 -

6pH Measurement.............................................................................................................- 7 -

6.1 pH Electrode .............................................................................................................- 7 -

6.2 pH Calibration ...........................................................................................................- 8 -

6.3 Notes about pH Calibration .......................................................................................- 9 -

6.4 Sample Test...............................................................................................................- 9 -

6.5 Recommended pH Electrodes for Different Applications .......................................... - 10 -

6.6 Parameter Setting ................................................................................................... - 11 -

6.7 Cleaning pH Electrode ............................................................................................. - 13 -

6.8 The Self-diagnose Information................................................................................. - 13 -

6.9 Notes about pH ....................................................................................................... - 14 -

7ORP Measurement: ....................................................................................................... - 14 -

8Limited Warranty........................................................................................................... - 16 -

Scan the QR code below to watch the tutorial video on Youtube.

- 3 -

1 Brief Instruction

Thank you for choosing Apera Instruments SX721 Portable pH/ORP Meter (will be called “the meter” in

short in the following content). Before using the meter, please read this instruction manual carefully in

order to help you properly use and maintain it.

The meter can measure the parameters of pH, ORP, and temperature of water solutions with high

accuracy. It is suitable for various applications in different industries e.g., water treatment, aquaculture,

horticulture, pools and spas, beverage making, mining, power plants, environmental monitoring, etc.,

especially ideal for in-field use.

The meter has the following features:

1.1. Built-in microprocessor chip with the intelligent functions of auto. calibration, auto. temperature

compensation, auto. salinity compensation, manual baromatric pressure compensation, data storage,

function settings, auto. power off, and low voltage display etc.

1.2. Adopts digital filter technology to intelligently improve meter’s response speed and accuracy. The

smiley face icon will appear when the reading is stable.

1.3. Pure water modes available for pH, significantly increasing the accuracy in pure water measurement.

1.4. Meter’s LCD screen has clear and bright backlit display.

1.5. Built-tough. IP57 waterproof and dust-proof.

2 Technical Specifications

2.1 pH

Measurement range

(-2.00 to 19.99) pH

Resolution

0.1/0.01 pH

Accuracy

Meter: ±0.01pH; Overall: ±0.02pH

Input current

≤2×10-12 A

Input impendance

≥1×1012 Ω

Stability

±0.01 pH/3h

Temp. compensation range

(0 to 100) °C (automatic)

- 4 -

2.2 ORP (mV)

Measurement range (mV/ORP/EH)

-1999mV to 0 to 1999mV

Resolution

1mV

Accuracy

Meter: ±0.1% FS, Overall: ±15mV

2.3 Other Technical Parameters

Data storage

200 sets

Data content

Serial number, measurement value, measurement unit, and

temperature

Power Supply

Two AA alkaline batteries (1.5V x2)

Dimensions and weight

Meter: (65×120×31) mm/180g

Complete Kit: (255 x 210x 50) mm/1380g

Quality and safety certification

CE, ISO 9001:2015

2.4 Working Condition

Working temperature

5 to 35°C

Working humidity

≤85%

IP rating

IP57 water-resistant

3 About the Meter

3.1 Screen Display

① —— Parameter icon ② —— Measurement value

③ —— Serial number and icon as measurement to be saved and recalled and indication icon for

special states.

- 5 -

M+ — measurement value to be saved; RM — Saved data to be recalled;

④ —— Measurement unit ⑤ —— Temperature measurement value and unit

⑥ —— Measurement stabilization icon ⑦ —— Electrode calibration indication icon

⑧ —— Indication icon of low battery power; appears when the voltage is less than 2.6V, calling

attention to replace the batteries.

3.2 Keypad

The meter has 5 operation keys in total.

Short press: press time <1 seconds; Long press: press time >2 seconds

3.2.1. — Short press to power on or off.

3.2.2. — Calibration key

(a) When in measurement mode, short press to enter calibration mode.

(b) When in parameter setting mode, short press to make changes.

3.2.3. — Function key

(a) In measurement mode, short press (<1.5s) to switch between and . Long press

to enter parameter setting (P1, P2, P3…)

(b) In other measurement mode, short press this key to enter the parameter setting mode (P1, P2, P3…)

3.2.4. — Back light and confirmation key

(a) In measurement mode, short press to turn on or ff the back light.

(b) In calibration mode or the parameter setting, press this key to make confirmation, and return to

measurement mode.

you confirm the selection.

3.2.5. — The key for data saving and recalliing

(a) When in measurement mode, short press to save the measurement data; Long press to recall the

saved data.

(b) When in parameter setting mode, press the key to make changes.

- 6 -

3.3 Data Log, Recall and Delete

3.3.1. Save the measurement:

In measurement mode, when the reading is stable and stays on screen, short press to save

the measurement data. M+ icon and the data serial number will show up on the upper right corner. The

meter can store up to 200 sets of data.

3.3.2. Recall saved data:

(a) In measurement mode, long press , the meter will recall the last saved data and the serial

number. RM icon will appear in the upper right corner of the screen.

Short press or again, the meter will recall all the data in turn, hold or

to quickly review the data.

(b) In data recalling mode (RM and serial number in the lower right corner), short press to return

to measurement mode.

3.3.3. Delete data:

In data recalling mode, hold for 5 seconds, CLr will show up for 2 seconds, meaning that all the

saved data have been eliminated. Then the meter will return to measurement mode.

4 What’s in the kit

SX721 pH/ORP meter *1

201T-S plastic pH/ATC three-in-

one combination electrode *1

301Pt-S plastic ORP

combination electrode *1

Carrying case *1

Screw driver *1

Spare AA batteries *2

User manual *1

pH standard buffer solution (pH 4.00, pH 7.00, pH 10.01) *1

50ml bottle/each

5 Preparation

What you need in addition to what’s in the kit:

Pure water (RO, distilled or deionized water) for rinsing off the electrode.

- 7 -

6 pH Measurement

Short press to turn on the meter. Connect 201T-S pH electrode to the meter (See Section 5 for

connection tutorial). The meter will automatically enter pH measurement mode.

6.1 pH Electrode

The meter comes with the 201T-S 3-in-1 combination electrode with a built-in temperature sensor, which

enables automatic temperature compensation. This electrode is only suitable for general water

solutions’ pH testing. Please refer to Section 6.5 for ideal pH electrodes to use for other applications. A

3M KCL storage bottle comes with the electrode, which is for storing the electrode when not in use to

keep the sensitivity of the probe.

6.1.1 Technical Specifications of the 201T-F pH Electrode

Measurement Range: 0 - 14 pH, 0 – 80°C (32 – 176˚F); Junction: Single Ceramic

Reference Electrode: Ag/AgCl Connector: 8-pin; Temperature unit: 30K Thermistor

Size: ø12*160 mm; Cable length: 1 meter

- 8 -

6.1.2 Use the Electrode

Screw off the KCL storage bottle, and put it aside (do not dump or spill the KCL solution). Rinse the

electrode with distilled or deionized water. Shake off excess water or blot-dry with clean tissue or kimwipe.

Stir the electrode for a few seconds after it’s dipped into the test solution and then hold it still. Wait for the

reading to get fully stabilized ( appears and stays) and then take the measurement. When the test

is finished, place the electrode in the storage bottle and tighten the cap to keep the sensitivity of the pH

sensor.

6.2 pH Calibration

6.2.1 After powering on the meter, short press to enter calibration mode, c1 flickers on LCD,

indicating the meter enters the first point calibration.

6.2.2 Rinse off the pH electrode in pure water and remove excess water, then insert it into the pH7.00

buffer solution, make a quick stir and then hold it still. When the reading is stabilized and stays on

screen, short press again to finish the 1st point calibration. “7.00 pH” will start flickering and a

flickering c2 will show up, indicating the 1st point calibration has been finished and the meter is entering

the 2nd point calibration.

6.2.3. Rinse off the pH electrode in pure water and remove excess water, then insert it into the pH 4.00

buffer solution, make a quick stir and then hold it still. When the reading is stabilized and stays on

screen, short press again to finish the 2nd point calibration. “4.00 pH” will start flickering and a

flickering c3 will show up, indicating the 2nd point calibration has been finished and the meter is entering

the 3rd point calibration.

6.2.4. Rinse off the pH electrode in pure water and remove excess water,

then insert it into the pH 10.01 buffer solution, make a quick stir and then

hold it still. When the reading is stabilized and stays on screen, short

press again to finish the 3rd point calibration. “10.01 pH” will start

flickering and then the meter will return to measurement mode.

will show up at the bottom left (see picture 4-1), indicating all 3 calibrations are finished.

- 9 -

6.3 Notes about pH Calibration

a) Keeping the freshness and cleanliness of calibration buffers is essential for accurate pH

measurement. The small bottles of pH buffers come with the meter should be replaced within 3

months after opening. The new buffer solutions should be made by a legitimate lab supply

manufacturer. Avoid sunlight and air contact when the buffers are not being used, and store at

room temperature.

1) This meter can adopt random 1-point, 2-point or 3-point automatic calibration. During calibration,

short press to return to measurement mode. When the measurement accuracy is ≤ ±0.1pH,

choose a buffer that’s close to the estimated measurement range and perform 1-point calibration

would be good. Choose pH 4.00 and pH 7.00 to calibrate if the measurement range is within the

acidity range (<pH 7) and choose pH 7.00 and pH 10.01 to calibrate if just within the alkalinity

range (>pH 7).

2) Choose 3-point calibration to achieve a more accurate measurement if the measurement range

is wide, or if the electrode has not been used for long. When connecting a new pH electrode, it

must be calibrated at 3 points.

3) The frequency that you need to calibrate your meter depends on the tested samples, condition of

electrodes, and the requirement of the accuracy. For high-accuracy measurements (≤ ±0.02pH),

the meter should be calibrated before test every time; For ordinary-accuracy measurements

(≥±0.1pH), once calibrated, the meter can be used for about a week or longer. In the following

cases, the meter must be re-calibrated:

•The electrode hasn’t been used for a long time or a new electrode is connected.

•After measuring strong acid (pH<2) or strong base (pH>12) solutions.

•After measuring fluoride-containing solution and strong organic solution.

•There is a significant temperature difference between the test sample and the buffer solution.

6.4 Sample Test

Power on the meter. Connect the pH electrode and the meter goes to pH measurement mode

automatically. Screw off the KCL storage bottle. Rinse the electrode with pure water. Shake off excess

water or blot-dry with clean tissue or kimwipe. Stir the electrode for a few seconds after it’s dipped into

the sample solution and then hold it still. Wait for the reading to get fully stabilized ( appears and

stays). Then save the measurement by pressing .

According to the pH isothermal measurement principle, the closer the test sample’s temperature is to the

- 10 -

calibration solution’s, the higher the accuracy of the measurement. This principle is recommended to

follow for the best result. For example: If you have to test at 150°F, we recommend warming up the

calibration solutions to the same temperature before performing calibration in order to get the most

accurate readings.

6.5 Recommended pH Electrodes for Different Applications

Application

Ideal Apera pH Electrodes

General water solutions

201T-S, LabSen 211, LabSen 213

Beverage, beer, wine

LabSen 211, LabSen 213

Low ionic strength solutions (RO water, distilled water,

deionized water…)

LabSen 801, LabSen 803

Liquid food (milk, cream, yogurt, jam, sauce, etc.)

LabSen 821, LabSen 823

High-Temperature solutions

LabSen 841, LabSen 861

Low-temperature liquid

LabSen881

High salinity solutions

LabSen 841

Complex and caustic solutions (e.g. electroplating)

LabSen 861

Raw meat

LabSen 761, LabSen 763

Micro sample testing

LabSen 241-6, LabSen 241-3

Cosmetics, skincare products

LabSen 851-1, LabSen 851-S

Soil

LabSen 551, LabSen 553

Solid or semi-solid samples (cheese, dough, fruits, meat

products, etc.)

LabSen 251, LabSen 751, LabSen

753

Strong acid solutions, HF containing solutions (HF

concentration<1%)

LabSen 831

Strong alkaline solutions

LabSen 841

Surface test (skin, paper, carpet, etc.)

LabSen 371

TRIS buffer solutions

LabSen 213, LabSen 223

Viscous solutions

LabSen851-S, LabSen 851-H

Wastewater or emulsion

LabSen 333

Indice

Altri manuali Apera Instruments Strumento di misura

Apera Instruments

Apera Instruments LabSen 821 Manuale utente

Apera Instruments

Apera Instruments PHB-3 Manuale utente

Apera Instruments

Apera Instruments PC 850 Manuale utente

Apera Instruments

Apera Instruments YD300 Manuale utente

Apera Instruments

Apera Instruments LabSen 851-H Manuale utente

Apera Instruments

Apera Instruments SX811-SS Manuale utente

Apera Instruments

Apera Instruments SX716 Manuale utente

Apera Instruments

Apera Instruments 2401T-F Manuale utente

Apera Instruments

Apera Instruments SX751 Manuale utente

Apera Instruments

Apera Instruments LabSen 753 Manuale utente

Apera Instruments

Apera Instruments SX811-BS Manuale utente

Apera Instruments

Apera Instruments SX731 Manuale utente

Apera Instruments

Apera Instruments EC700 Manuale utente

Apera Instruments

Apera Instruments YD300 Manuale di istruzioni

Apera Instruments

Apera Instruments WS100 Manuale utente

Apera Instruments

Apera Instruments LabSen 851-1 Manuale utente

Apera Instruments

Apera Instruments TN420 Manuale utente

Apera Instruments

Apera Instruments LabSen 221 Manuale utente

Apera Instruments

Apera Instruments 2310T-F Manuale utente

Apera Instruments

Apera Instruments TN400 Manuale utente

Apera Instruments

Apera Instruments LabSen 241-3SP Manuale utente

Apera Instruments

Apera Instruments GroStar AI101G Manuale utente

Apera Instruments

Apera Instruments DO850 Manuale utente

Apera Instruments

Apera Instruments 950 Series Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente