Apera DJS-0.1-C Manuale utente
DJS-0.1-C Conductivity Electrode Instruction Manual
Model
Cell
constant
Electrode
size
Dimension
size
Socket
Electrode
body
Cable
length
Range
DJS-0.1-C
0.1
7×18mm
platinum
Φ12×155
BNC
Glass
1m
(0-200)
µS/cm
Use and maintenance:
1.1 Connect the DHS-0.1-C conductivity electrode to your conductivity meter. Set the cell constant
to 0.1. Then calibrate the meter in the lower calibration point (e.g. 84 µS/cm).
1.2 Keep the conductivity electrode clean, before and after the measurement, rinse the electrode
with deionized water/distilled water. In order to maintain the highest measurement accuracy, we
recommend rinsing the electrode several times with your test sample solution.
1.3 A Flow cell (included) is recommended when testing ultra-low conductivity solutions like ultra-
pure water. It helps reduce the influence from contact with air and minimizes reading error. Use
a rubber tube (7mm in diameter, not included) to connect your water source on the low end of
the flow cell. When water flows through the glass cell, conductivity can be measured without air.
1.4 How to clean a conductivity electrode:
(a) Use warm detergent water or alcohol to clean off organic contaminants on the electrode.
(b) Use 10% lemon acid to clean calcium and magnesium sediments.
1.5 Conductivity electrode storage: Store dry when not in use.
Limited Warranty
We warrant this electrode to be free from defects in material and workmanship and agrees to repair
or replace free of charge, at option of APERA INSTRUMENTS, any malfunctioned or damaged product
attributable to responsibility of APERA INSTRUMENTS for a period of six months. Warranty period
is the time limit to provide free service for the products purchased by customers, not the service life
of the tester or electrodes.
This limited warranty does not cover any damages due to:
•transportation;
•storage;
•improper use;
•failure to follow the product instructions or to perform any preventive maintenance;
•combination or use with any products, materials, processes, systems or other matter
notprovided or authorized in writing by us;
•unauthorized repair;
•normal wear and tear; or
•external causes such as accidents, abuse, or other actions or events beyond our reasonable
control.
APERA INSTRUMENTS (Europe) GmbH | Wilhelm-Muthmann-Str.18, 42329 Wuppertal, Germany
info@aperainst.de | www.aperainst.de | Tel.: +49 202 51988998
Indice
Altri manuali Apera Strumento di misura
Apera
Apera PC60-Z Manuale utente
Apera
Apera 2310T-S Manuale utente
Apera
Apera PH60S Manuale utente
Apera
Apera PC60-Z Manuale utente
Apera
Apera LabSen AI3102 Manuale utente
Apera
Apera LabSen 232 Manuale utente
Apera
Apera PC60-Z Manuale utente
Apera
Apera 201DJ-C Manuale utente
Apera
Apera EC400S Manuale utente
Apera
Apera 2310T-F Manuale utente
Apera
Apera 2401-C Manuale utente
Apera
Apera PH60 Manuale utente
Apera
Apera PC60-Z Manuale utente
Apera
Apera TDS20 Manuale utente
Apera
Apera EC60-Z Manuale utente
Apera
Apera EC60 Manuale utente
Apera
Apera ORP60 Manuale utente
Apera
Apera 201DJ-C Manuale utente
Apera
Apera ORP60-Z Manuale utente
Apera
Apera PC60 Manuale utente
