Applied Instruments XR-3 Istruzioni per l'installazione e il funzionamento

Application Note

10/29/2015

Page 1 of 2

Installing Bell TV DishPro Plus (DP Plus) Twin

systems using the XR-3 satellite meter

Connections: Coax cable connected from an LNBF output port to the XR-3 satellite meter’s ODU / LNB

port

Meter Setup:

Press the SYST System soft-key (located near upper left corner of LCD screen) to select the following:

REGION your geographic region

SERVICE Bell TV

SYSTEM Dish Pro

LNB MODEL DP Plus Twin or other as applicable if using an external multi-switch

SWITCH TYPE defaults to DpTwin (assuming you’ll be connected directly from meter to LNB)

To make selections, arrow up or down to the item to change and press Enter, then arrow up or down to

the desired option and press Enter. Press EXIT or DONE to return to Run Mode

Azimuth/Elevation Lookup:

Press the AZ/EL soft-key (lower left corner of main Run screen), use the numeric keypad to enter the

Postal Code for your current location, and press the ENTER key. Press EXIT soft-key to return to Run

Mode.

Antenna Pointing

Install the mast (pole) plumb, preset the antenna reflector’s vertical angle (elevation setting) and Skew

setting, mount antenna reflector to mast, and grossly align azimuth (using magnetic compass according

to ‘Magnetic’ coordinates shown in AZ/EL screen on meter). You may want to use the AZ/EL look-up

feature to obtain rough antenna reflector settings based on your postal code or latitude and longitude.

Run Mode:

Press LNB soft-key (located on middle right side of LCD screen) once to power the LNB and go to

LNB1 (91°W). The satellite orbital position will be shown in upper left corner of LCD screen.

Adjust antenna reflector azimuth (left or right) and elevation (up or down) to obtain maximum signal

level (left bar graph), signal quality (right bar graph), and LOCK status.

Press the ID soft-key (located on middle left side of LCD screen) to verify that you’re aligned to the

91°W satellite. "ID VERIFIED" means you are pointed correctly.

Application Note

10/29/2015

Page 2 of 2

If "ID FAILED" is displayed, press SCAN soft-key and the XR-3 will find which satellite you are aimed

at.

If desired, you may also use Up/Down arrow keys to scroll through other transponders to check for

proper level and quality.

Press LNB soft-key (located on middle right side of LCD screen) again to toggle to LNB2 (82°W).

The satellite orbital position will be shown in upper left corner of LCD screen.

Adjust the Skew of the dish (Rotate the antenna reflector clockwise or counter-clockwise to maximize

signal level and quality).

Press the ID soft-key to verify that you’re aligned to the 82°W satellite. “ID VERIFIED” means you are

pointed correctly.

If desired, you may also use Up/Down arrow keys to scroll through other transponders to check for

proper level and quality.

NOTE: For multi-LNBF systems you should always use the LNB soft-key instead of the left / right arrow

keys to toggle between the different feed horns and select different satellites.

You may choose to use the PoP Scan function of the meter to record the measurements. Please

refer to the operations manual for more info and instructions related to the Proof of Performance scan

feature.

Notes:

It is NOT recommended to keep the XR-3 meter in line while checking receiver status due to

attenuation from our circuitry.

Please ensure that you have the latest versions of North American Field Guide, Software,

Dish Limit values, and Postal Codes loaded into your meter. If your meter has older versions

loaded, please use the FlashUpdate program to update your meter, as described in the

Operations Manual.

Applied Instruments, Inc. • 5230 Elmwood Ave. • Indianapolis, IN USA 46203 • Tel (317) 782-4331 • www.appliedin.com

Altri manuali per XR-3

Indice

Altri manuali Applied Instruments Strumento di misura

Applied Instruments

Applied Instruments DIRECTV SWM SL5S KaKu Istruzioni per l'installazione e il funzionamento

Applied Instruments

Applied Instruments DIRECTV SWM SL5s Istruzioni per l'installazione e il funzionamento

Applied Instruments

Applied Instruments DP Plus Istruzioni per l'installazione e il funzionamento

Applied Instruments

Applied Instruments NPRT 2200 Manuale utente

Applied Instruments

Applied Instruments Super Buddy Manuale utente

Applied Instruments

Applied Instruments Sat Buddy Manuale utente

Applied Instruments

Applied Instruments T12 LO-11300 Istruzioni per l'installazione e il funzionamento

Applied Instruments

Applied Instruments Sat Buddy 2 Manuale utente

Applied Instruments

Applied Instruments Super Buddy 1000.4 East Istruzioni per l'installazione e il funzionamento

Applied Instruments

Applied Instruments Super Buddy Signal Level Meter Istruzioni per l'installazione e il funzionamento

Applied Instruments

Applied Instruments Dual Buddy Manuale utente

Applied Instruments

Applied Instruments XR-3 Manuale utente

Applied Instruments

Applied Instruments AI Turbo S2 Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente