Arec KL-3WT Manuale utente
KL-3WT
Media Station
ENGLISHQuick Installation Guide
AREC Inc.© All Rights Reserved 2019. l www.arec.com
All information contained in this document is Proprietary
KL-3WT Quick Installation Guide
FCC
Federal Communication Commission interference statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures: -Reorient or relocate the receiving antenna. -Increase the
separation between the equipment and receiver. -Connect the equipment into an outlet on a
circuit different from that to which the receiver is connected. -Consult the dealer or an
experienced radio/TV technician for help.
RF Exposure Warning
The equipment complies with RF exposure limits set forth for an uncontrolled environment. The
antenna(s) used for this transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
You are cautioned that changes or modifications not expressly approved by the party responsible
for compliance could void your authority to operate the equipment.
FCC Caution
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received, including interference that may
cause undesired operation
This equipment should be installed and operated with a minimum distance of 20 centimeters
between the radiator and your body.
Notice: Any changes or modifications not expressly approved by the party responsible for
compliance could void your authority to operate the equipment.
CE
Hereby, AREC Inc., declares that this Media Station is in compliance with the essential
requirements and other relevant provisions of Directive 2014/53/EU.
1
2
KL-3WT Quick Installation Guide
CB
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type.
– the ventilation should not be impeded by covering the ventilation openings with items, such as
newspapers,table-cloths, curtains, etc.:
– no naked flame sources, such as lighted candles, should be placed on the apparatus;
– attention should be drawn to the environmental aspects of battery disposal;
– the use of apparatus in tropical climates.
the instructions for use shall state that the apparatus shall not be exposed to dripping or
splashing and that no objects filled with liquids, such as vases, shall be placed on the apparatus.
KL-3WT Quick Installation Guide
3
Introduction
Specifications
Package Contents
Featuring a compact and stand-alone design, AREC KL-3WT Media Station consists of diverse
features and functionality, including multi-signals capturing, recording synchronously, codec,
streaming online, live broadcasting, and web-based monitor page, providing complete
presentation or lecture capture solution.
HDMI Line RJ-45 Line
KL-3WT
Media Station
KL-3WT
354mm(L) x 188.2mm(W) x 91.35mm(H)
2840g
12V / 3A
36W (Max.)
0ºC ~ 40ºC / 90%
Insert 1 IP CAM to LAN port and insert 2 video signals
(either HDMI or VGA input). Using external USB flash to
record the transcoded video / audio. And output the
transcoded video / audio to HDMI port.
Product Name
Model Name
Dimension
Weight
Power Requirement
Power Consumption (Max.)
Operating Temperature / Humidity
Maximum normal load description
Quick Installation Guide Power Adapter
VGA Line
HDMI-to-VGA converter WiFi Module Antenna
Wireless Mic. Antenna
Terminal Block
KL-3WT Quick Installation Guide
4
Product Appearance
Top View
Back View
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
10.1” LCD Display
Record function keys
Power
Front USB port
Power port
Video input
Video input
Video output
Audio input
Audio input
Audio output
Network port
Network camera input
RS-232
Reset button
Antenna port for Camera
Antenna port for
Microphone
NOTE: The port can detect and record to USB storage devices using FAT32, NTFS file systems.
NO. Name Brief introduction
Preview mixed recording
Control the Record, Pause, Stop function
Power on/off the device
1.For external USB storage device*
2.Firmware update through USB disk
12V/ 3A
VGA/ HDMI input source for PC [ ]
VGA/ HDMI input source for camera [ ]
1.HDMI loop thru from input [ ]
2.VGA output can use the HDMI-to-VGA converter
Line audio input
Mic audio input
Line audio output
RJ-45 Ethernet connector for network connection
1.RJ-45 Ethernet connector for network camera input source
2.Connected to setting PC for device configuration and control
Captive screw connector for control over RS-232
Restoring devices to its factory default state
Connected to antennas for wireless cameras receive
Connected to antenna for wireless microphone
2 3 4
5 6 7
15
149 108 1211 13 17
16
1
KL-3WT Quick Installation Guide
5
Connection
AREC Wireless
Full HD Camera
notebook
document cam
Speaker
DV
RS-232
AREC Wireless
Full HD Camera
Power
Video output VGA / HDMI
Video input VGA / HDMI
USB
projector
TV
Audio output
Line audio input Mic audio input
amplifier microphone network
AREC
Network Camera
Setting PC
AREC
Wireless
Microphone
USB drive
projector
KL-3WT Quick Installation Guide
6
Accessing the Administrator pages
Connect PC to the setting port of Media Station with standard network cable.Open up the
browser, and input 192.168.11.254 in the broswer page. Log in Administrator with
username admin and password admin, then entering System Administration webpages.
192.168.11.254
192.168.11.254
KL-3WT Quick Installation Guide
7
The system automatically scans and lists the network
cameras connected to the Media Station once entering the
[ Network device manager ] page. You may click Refresh
button to scan again. Click Login button and the login
authentication dialog pop out. Enter the username and
password of the camera to complete the authentication and
change the status to [ OK ]. Then the camera is ready for
video input selection. Select the desired camera by its IP
address. For signal type of encoder, enter RTSP or RTP
connection URL.
Setup
Step 1: Set up video input name, signal type,video source, PTZ control in [ Video inputs ] of
[ Media I/O ]. The Capture source can be the video port [ ] and [ ] with option VGA
or HDMI. If only one of the latter is connected, the system would detect and automatically
switch to source of signal. If both options are connected, set the capture priority between
those.
If the desired video source is network camera, a login authentication with the camera is
required firstly in the [ Network device manager ] setup tab of [ Media I/O ].
KL-3WT Quick Installation Guide
8
Start a recording from the front panel
Press [ ] button and recording begins. The LED indicator of [ ] button is red to indicate
active recording.
Press [ ] button to pause recording. The LED indicator of [ ] button flashes red while
recording is paused. To resume recording, press [ ] button or press [ ] button. The preview
and the output video are also suspended while recording is paused.
Press [ ] button to end a recording.
Getting start a recording
Step 2: Set up audio volume in [ Audio ] of [ Media I/O ].
Step 3: Set up date and time of host machine in [ System settings ] of [ System ].
9
KL-3WT Quick Installation Guide
The Online director allows user to control recording function and check on the preview screen.
The control panel makes it easy to apply layout, select background, and control the audio
recorded during the recording process.
Start a recording via the Online director
Entering the Online director webpage via [System Administration] by clicking the [ ] button
and opening a new tab; or log in Online director from the initial login page with default username
director and password director. Both ways lead to the Online director control panel for
web-based users.
Altri manuali per KL-3WT
1
Indice
Altri manuali Arec Server
