Armstrong 3031S Manuale di istruzioni
Model No. q Model 320
q Model 320D
Serial No. :
Ship Date :
Model 320
Installation and Maintenance
Water Temperature Controls
Groups of Fixtures - Thermostatic
Keep this manual with installation for
future reference.
Armstrong International
221 Armstrong Blvd., Three Rivers, Michigan, 49093 - USA
armstronginternational.com/brain
2
Introduction.............................................................. 3
Specications .......................................................... 5
General Advisory ..................................................... 5
Safety ...................................................................... 6
Pack Contents ......................................................... 7
Schematic Piping..................................................... 8
Installation ............................................................... 9
General................................................................ 9
Installation Requirements.................................... 9
Tools Required .................................................... 9
Installation Procedure........................................ 10
Commissioning...................................................... 12
Operation............................................................... 13
Servicing & Maintenance....................................... 14
Spare Parts............................................................ 17
Troubleshooting..................................................... 20
Notes ..................................................................... 22
Limited Warranty and Remedy .............................. 24
Contents
3
Thermostatic Mixing Valves (LPM and BAR)
Model
320
Pressure Drop (BAR) Min.
Flow CV
0.3 0.7 1.0 1.4 1.7 2.1 2.4 2.8 3.1 3.4
LPM 30.3 41.6 49.2 56.8 64.4 71.9 75.7 83.3 87.1 90.8 3.8 3.4
Thermostatic
Model 320
Thermostatic Mixing Valve of “sealed for life” disposable
cartridge construction. Compact design with top and/or bottom
blended water outlet makes the Model 320 ideal for recessed
enclosure, plumbing chase and utility/mechanical room
installation.
Complete operating mechanism of valve is enclosed in a
durable polymer cartridge for ease of field maintenance.
Powerful internal mechanism and non metallic wetted parts
resist mineral deposition.
Capable of close temperature control at diverse flow rates
between 1 gpm (3.8 lpm) and 24 gpm (91 lpm). Able to blend
within 5°F (2°C) of either inlet supply due to “low seepage”
across internal proportioning mechanism.
Operational Specifications
• Dual thermostatic elements provide redundancy in the
event of individual thermostat failure
• Typical outlet temperature control +/-2°F
• Adjustable maximum temperature limit stop
• Adjustable single temperature lockout
• Thermal shutdown mode upon inlet supply failure
Technical Specifications
• 3/4” MNPT inlets and 3/4” MNPT outlet
• Chrome-plated brass/polymer construction
• Lead Free compliant
• Operating pressures
Maximum: 150 psi (10 bar)
Minimum: 10 psi (.7 bar)
• Integral inlet check valves and strainers
• ASSE 1017 and CSA B125 certified
• Shipping weight 10 lbs (4.5 kg)
Thermostatic Mixing Valves (GPM and PSI)
Model
320
Pressure Drop (PSI) Min.
Flow CV
5 10 15 20 25 30 35 40 45 50
GPM 8 11 13 15 17 19 20 22 23 24 1.0 3.4
Designs, materials, weights and performance ratings are
approximate and subject to change without notice. Visit
armstronginternational.com for up-to-date information.
Armstrong Hot Water Group, 221 Armstrong Blvd., Three Rivers, MI 49093 – USA
Phone: 269-279-3602, Fax: 269-279-3130
Water Temperature Control - Groups of Fixtures
4.61
(117.0)
7.29
(185.2)
1.04
(49.3)
5.38
(136.6)
HOT
INLET
COLD
INLET
MIXED
OUTLET
4
Thermostatic Mixing Valves (GPM and PSI)
Model
320D
Pressure Drop (PSI) Min.
Flow CV
5 10 15 20 25 30 35 40 45 50
GPM 8 11 13 15 17 19 20 22 23 24 1.0 3.4
Designs, materials, weights and performance ratings are
approximate and subject to change without notice. Visit
armstronginternational.com for up-to-date information.
Armstrong Hot Water Group, 221 Armstrong Blvd., Three Rivers, MI 49093 – USA
Phone: 269-279-3602, Fax: 269-279-3130
Thermostatic
Model 320D
A derivative of the standard Model 320 Thermostatic Mixing
Valve for institutional group fixture control. Compact design with
top and/or bottom blended water outlet makes Model 320 ideal
for recessed enclosure, plumbing chase and utility/mechanical
room installation.
Factory supplied pre-plumbed and pressure-tested Model
320D is supplied as standard with inlet check valves, strainers,
unions, isolations valves and outlet thermometer and stop
valve*.
*Model 320D is supplied with top outlet and can be site
reconfigured for bottom outlet applications.
Operational Specifications
• Dual thermostatic elements provide redundancy in the
event of individual thermostat failure.
• Typical outlet temperature control +/-2°F
• Adjustable maximum temperature limit stop
• Adjustable single temperature lockout
• Thermal shutdown mode upon inlet supply failure
Technical Specifications
• 3/4” NPT inlets and 3/4” NPT outlet
• Chrome plated brass/polymer construction with self finish
brass and bronze lead free components
• Lead Free compliant
• Operating pressures
Maximum: 150 psi (10 bar)
Minimum: 10 psi (.7 bar)
• Inlet check valves, strainers, unions and isolation valves
• Fitted with outlet thermometer and isolation valve
• ASSE 1017 and CSA B125 certified
• Shipping weight 18 lbs (8.1 kg)
For a submittal drawing, refer to D61051.
Water Temperature Control - Groups of Fixtures
Thermostatic Mixing Valves (LPM and BAR)
Model
320D
Pressure Drop (BAR) Min.
Flow CV
0.3 0.7 1.0 1.4 1.7 2.1 2.4 2.8 3.1 3.4
LPM 30.3 41.6 49.2 56.8 64.4 71.9 75.7 83.3 87.1 90.8 3.8 3.4
7.6
(194)
3.8
(97)
TYP
12.2
(311)
7.8
(198)
TYP
5
Specications
*Model 320 can accept temporary excursions above 185°F (85°C) and maintain control without sustaining
internal damage. (ASSE 1017 certification requires exposure to 200°F (93°C) for a period of 30 minutes).
Prolonged operation of the Mixing Valve at such elevated temperatures is not recommended.
** Normal operating conditions are considered as a differential of approximately 122°F (50°C) between
the hot and cold inlet temperatures, and with differentials of 59°F (15°C) - 95°C (35°C) between the
blend setting and either supply. 59°F (15°C) is the optimum published minimum differential required to
achieve full thermal performance.
General Advisory
This Model 320 Valve has been supplied for this application based upon information provided to Armstrong at the
time the order was placed.
This Model 320 Valve is configured for use in a “dead-leg” piping configuration.
This Model 320 Valve has not been congured for use in a central pumped re-circulation system.
This Model 320 Valve is not designed to deliver tepid water to emergency fixtures.
For further information, please call our technical department 1-269-279-3602 between 08:00 a.m. to
05:00 p.m. EST.
Operating Specications
Maximum Hot Water Supply Temperature185° 185°F (70°C)*
Minimum Cold Water Supply Temperature33° 33°F (1°C) - 77°F (25°C)
Optimum Minimum Inlet to Outlet Temperature Differential 59°F (15°C)**
Optimum Thermostatic Control Range 86°F (30°C) - 122°F (50°C)
Flow Rate at 45 psi 23 gpm (87 lpm)
Minimum Flow Rate 1 gpm (3.8 lpm)
Maximum Inlet Supply Pressure 150 psi (10 bar)
Minimum Inlet Supply Pressure 10 psi (0.7 bar)
6
Safety
Applicable codes must be followed and supersede any other instructions.
Generally applicable codes in the US include:
• IPC (International Plumbing Code)
Read this manual
Improper installation or operation may cause a ood resulting in property
damage, personal injury, or death. Armstrong strongly recommends that
a qualied installer be used.
Service must be performed by a qualied person.
Improper installation, start-up, operation, maintenance, or service may
void the warranty.
Hot water or metal may cause scald burns. Skin exposure to 140°F water
or metal for only ve seconds may cause a second degree burn.
Icon Legend
If instructions are not followed:
- injury or death and property damage are imminent
- injury or death and property damage are possible
- potential property damage, expensive repairs, and/or voiding
the warranty may result
The function of a Thermostatic Mixing Valve is to deliver water consistently at a pre-designated temperature.
Model 320 Thermostatic Mixing Valves are precision engineered to give continued superior and safe
performance provided:
1. They are installed, commissioned, operated and maintained in accordance with the recommendations
provided and accepted plumbing practices.
2. Periodic attention is given, as necessary, to maintain the product, the accessory fittings and the plumbing
system in good functional order.
In keeping with every other mechanical product, Model Mixing Valves should not be considered as
functionally infallible and, as such will never totally replace the vigilance and attention of facility nursing/
bathing or other institutional supervisory or industrial safety staff.
Provided that they are installed, commissioned, operated and maintained, the risk of product failure and
its associated consequences, if not eliminated, are reduced to the minimum achievable.
7
Pack Contents
X 1
X 1
X 1
X 3
X 1
8
Schematic Piping
Hot Water Supply
Water Heater
Model 320
Mixed Flow
Cold Water Supply
System Layout
Thermometer
Sink
Shower
Check Valve
Isolation Valve
Stop Valve
Flow Direction
Pipeline
9
Installation
General
Installation must be carried out in accordance with these instructions, and must be conducted by designated,
qualied and competent personnel.
The installation must comply with all relevant local and state water plumbing codes.
All plumbing components are to be supplied by the installer. Failure to include these components will compromise
the product, system performance and will void the warranty.
Notes:
1. Model 320 is supplied fully performance and pressure tested.
2. Suitable connections for ease of maintenance should be used on the inlet and outlet ports. (Isolation valves
and unions.)
3. The hot and cold water inlet supply pressures must be nominally equal.
4. The inlet supply pipework must be thoroughly ushed before tting the Model 320 valve.
5. The Model 320 can be installed in both rising supplies and falling supplies.
Installation Requirements
1
2
3
4
5
The use of supply strainers will reduce debris entering the Model 320. The recommended gauge for such
strainers is 35 mesh (mesh aperture dimension = 0.5mm).
Inlet pressure tappings which allow measurement of the inlet pressures to the Model 320 under operating
conditions are particularly recommended for in-service testing.
Pipework must be rigidly supported to avoid any strain on the connections.
Inlet and outlet threaded joint connections should be made with PTFE thread sealing tape or liquid sealant.
Do not use oil-based, non-setting joint compounds.
Run water for 1 minute from both hot and cold supplies to eliminate pipe debris. It is essential that supply
pipes are thoroughly ushed through before connection to the Model 320.
Tools Required
Driling Drill Bit Screw Driver Pencil Adjustable Allen Keys Safety
Machine size 6 mm Plus & Minus Spanner 3mm & 2.5mm Glasses
10
1
3
4
2
Ø 6 mm
a. Unscrew the set screw.
b. Remove the Backplate.
a. Use the Backplate to mark the four mounting holes at
the desired height.
b. Drill the holes (6 mm) and t the wall anchors. Screw
the Backplate to the wall.
Caution! Avoid area where underground wirings
or pipelines pass through.
a. Mount the Valve assembly on the Backplate xed on
the wall. Make sure the Valve assembly locks in the
groove.
b. Tighten the set screw.
a. Important! Prior to assembly of the hot and cold
adapters, look inside each one and ensure that there
is a strainer and a white plastic checkvalve. The
adapter with nothing inside is for the outlet.
Thread the coupling nuts onto the Valve assembly
then tighten using an adjustable spanner.
Caution! Use a soft cloth to protect the plating
from damage while tightening the spanner.
Step 1
Step 3
Step 2
a
b
Step 4
2.5 mm
2.5 mm
6.0 mm
Questo manuale è adatto per i seguenti modelli
9
Indice
Altri manuali Armstrong Unità di controllo
Armstrong
Armstrong A Series Manuale utente
Armstrong
Armstrong 1-AV Manuale utente
Armstrong
Armstrong TVS 4000F Manuale utente
Armstrong
Armstrong Steamix VE-M Manuale di istruzioni
Armstrong
Armstrong 425 Manuale di istruzioni
Armstrong
Armstrong 880100-002 Manuale utente
Armstrong
Armstrong 880A Series Manuale utente
Armstrong
Armstrong BRAIN DMC80 Manuale utente
Armstrong
Armstrong 880 Series Specifiche tecniche
Armstrong
Armstrong The Brain DRV80R Manuale utente
Armstrong
Armstrong 320 Manuale di istruzioni
Armstrong
Armstrong FTV Manuale utente
Armstrong
Armstrong CD72SR Manuale utente
Armstrong
Armstrong 3750 Manuale utente
Armstrong
Armstrong DRV40 Manuale utente
Armstrong
Armstrong Emech F3 Manuale di istruzioni
Armstrong
Armstrong OB 2000PT Manuale
Armstrong
Armstrong OB-2000PT Integral Manuale utente
Armstrong
Armstrong Emech F2 Manuale di istruzioni
Armstrong
Armstrong The Brain DRV25 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
