Artila Aport-214PG Istruzioni per l'installazione
Copyright © Artila Electronics Co., Ltd. All Rights Reserved
Aport-214PG
FreeRTOS Programmable Device Server
Hardware Guide
Version: 1.0
2018 APR.
Aport-214PG ardware Guide
ARTILA
2
Trademarks
The Artila logo is a registered trademark of Artila Inc. All other trademarks or registered
marks in this manual belong to their respective manufacturers.
Disclaimer
Information in this document is subject to change without notice and does not
represent a commitment on the part of Artila.
Artila provides this document as is, without warranty of any kind, either expressed or
implied, including, but not limited to its particular purpose. Artila reserves the right to
make improvements and/or changes to this manual, or to the products and/or the
programs described in this manual, at any time.
Information provided in this manual is intended to be accurate and reliable. owever,
Artila assumes no responsibility for its use, or for any infringements on the rights of
third parties that may result from its use.
This product might include unintentional technical or typographical errors.
Changes are periodically made to the information herein to correct such errors,
and these changes are incorporated into new editions of the publication.
Aport-214PG ardware Guide
ARTILA
3
Document Amendment History
Revision
Date Remark
V 1.0 2018 Apr. Initial
Aport-214PG ardware Guide
ARTILA
4
Table of ontents
1.
Introduction .................................................................................................... 5
1.1
Features................................................................................................ 5
1.2
Specifications ........................................................................................ 5
1.3
Packing List .......................................................................................... 6
1.4
Optional Accessory ............................................................................... 6
2.
Layout ............................................................................................................. 7
2.1
Outline .................................................................................................. 7
2.2
Dimension ............................................................................................. 8
3.
Pin Assignment and Definition...................................................................... 9
3.1
LED Indicator ........................................................................................ 9
3.2
Power In: (+9 ~ +48VDC) ...................................................................... 9
3.3
RS-485 Serial Port (D1 & D2) ............................................................... 10
3.4
Relay Output (DO0 & DO1) ................................................................... 10
3.5
Isolated Digital Input.............................................................................. 10
Aport-214PG ardware Guide
ARTILA
5
1. Introduction
Aport-214PG is a FreeRTOS Programmable Device Server. It features Ethernet, RS-
485 and DIO in a single unit and is C programmable with embedded web server.
Software developer can use powerful Atmel Studio to program to compile and debug
their applications. Lots of example programs are included for users to jump start their
applications. A Manager utility is included to discover Aport-214PG and upgrade its
application firmware remotely.
1.1 Features
Atmel SAM4E16E ARM Cortex-M4 120M z
1MB on-chip flash and 128KB on-chip SRAM.
2MB flash and 128KB SRAM via SPI expansion
One 10/100Mbps Ethernet port
Two RS-485 serial port
Four isolated Digital input
Two Relay output
FreeRTOS operating system
Support lwIP and BSD socket library
Support tiny web server
Windows configuration utility included
Toolchain: Atmel Studio
One Micro-SD Card interface
Low Power operating
Remote firmware upgrade
1.2 Specifications
PU: Atmel SAM4E16E Cortex-M4 120M z
Memory: 1MB on-chip flash and 128KB on-chip SRAM
2MB flash and 128KB SRAM via SPI expansion
Mass Storage:
MicroSD socket inside x 1
SD 2.0 compliant, Support SD C
Network Interface:
1 x 10/100Mbps Ethernet
RJ45 Connector
Protection: 1.5KV Magnetic isolation
Aport-214PG ardware Guide
ARTILA
6
Serial port:
2 x RS-485
Signal: Data+ (D+), Data-(D-)
RS-485 Automatic Flow Control: Yes
Isolation digital input:
Channel number: 4
Photo isolation (AC in): 2500Vrms
Logical igh: 5~24Vdc
Logical Low: 0~1.5Vdc
Input type: AC input
Input resistance: 1.2K [email protected]W
Relay output:
Channel number: 2
Contact rating: 30VDC@1A or 125VAC@0.5A
Pin define: NC / COM / NO
Power Input: +9 ~ +48VDC, terminal block
Dimension (W x L x ): 78 x 108 x 24mm (3.0 x 4.25 x 0.94in)
Weight: 290g (0.64lb)
LED Indicator: Power, Ready, DO, RS-485, LAN, Status (user defined)
Operating Temperature: 0~70°C
Installation: Wall mounting, DIN-rail mounting (with optional kit)
1.3 Packing List
Aport-214PG: Programmable device server
Software toolchain (download from Atmel web support)
Manager Utility (download from Artila web)
1.4 Optional Accessory
DK-35A (36-DK35K-000): DIN RAIL Mounting Kit
PWR-12V-1A (31-62100-000): 110~240VAC to 12VDC 1A Power Adaptor
Aport-214PG ardware Guide
ARTILA
7
2. Layout
2.1 Outline
Aport-214PG ardware Guide
ARTILA
8
2.2 Dimension
Unit=mm
Aport-214PG ardware Guide
ARTILA
9
3. Pin Assignment and Definition
3.1 LED Indicator
The LED provides the Aport-214PG operation information described as follow:
RDY: Ready LED keeps ON when Aport-214PG software is ready for operation.
PWR: Power LED keeps ON if power (+9VDC to +48VDC) is correct.
DO0 / DO1: These LEDs indicate the relay status. When the coil of relay is
energized, the LED will be ON.
LAN: Link and Activity LED will turn ON when the Ethernet cable is connected.
When there is network data traffic, this LED will flash.
STATUS: User defined, control by software/GPIO
RS-485 (D1/D2): This LED is dual color and it indicates the serial data traffic of RS-
485 respectively. The Yellow LED stands for receiving data and Green LED means
transmitting data.
3.2 Power Input
Connecting +9 ~ +48VDC power line to the Power in terminal block(V+/V-). If the power
is properly supplied, the Power LED will keep solid green and a beep will be heard.
V+: DC power + in
V-: Power ground
Aport-214PG ardware Guide
ARTILA
10
3.3 RS-485 Serial Port (D1 & D2)
D1+ / D2+: Data+
D1- / D2-: Data-
Enable/Disable Termination resistor for RS-485 (J2 & J3)
The Aport-214PG equips on-board 120Ohm termination resistor for each RS-485 port.
Default setting is disable termination resistor. In order to enable termination resistor,
please remove the top cover of the Aport-214PG, and the adjust the associated jumper
to short position1 - 2, shown below:
J2 is termination resistor selection for RS-485(D1)
J3 is termination resistor selection for RS-485(D2)
Termination Resistor Enabled
Termination Resistor Disabled (default)
3.4 Relay Output (DO0 & DO1)
DO0_N : Relay two normal close
DO0_ OM: Relay two common
DO0_NO: Relay two normal open
DO1_N : Relay one normal close
DO1_ OM: Relay one common
DO1_NO: Relay one normal open
3.5 Isolated Digital Input
DI0: Digital input 1
DI1: Digital input 2
DI2: Digital input 3
DI3: Digital input 4
DI OM: Common pin of DI0~DI3
DI1~4
DI_COM
3 2 1
3 2 1
J
2
J
3
Indice
Altri manuali Artila Server
