ATCOM IPPBX Manuale utente
IP-PBX Quick Start Guide
Introduce...........................................................................................................................................3
Configure and set up the IP-PBX .......................................................................................................4
How to change the IP address...........................................................................................................7
Set up extensions and make internal calls ........................................................................................8
How to make calls via the FXO port ................................................................................................10
How to make VoIP outgoing call?....................................................................................................12
IVR—Auto Attendant.......................................................................................................................14
Procedure to set up the IVR ....................................................................................................14
Advance option for IVR ...........................................................................................................16
IVR Configure Example............................................................................................................17
Backup and restore configure .........................................................................................................18
Debug the IP-PBX ............................................................................................................................19
Introduce
This is the quick start guide for ATCOM IP-PBX series. It includes the procedure for how to set up
the IP-PBX as a basic IP-PBX system.
Configure and set up the IP-PBX
You need another computer to access and configure the IP-PBX. There are several ways to access
the IPXX series products. Different ways has different usage. The web/SSH accesses are base on
network connection which you need internet connection. And the console port access is via the
RS232 console cable which allows you to access the devices when you fail to access to it via
network.
Web access
It is the most common way to access the IP-PBX. Most settings can be done through the web
interface. Connect the IP-PBX’s WAN port to your switch. Simply put the device’s WAN port IP
address (the default IP address of IP-PBX is 192.168.1.100) in your web browser (better use
Firefox, there is compatible issue with IE) and enter the username and password to access the
device.
The web access username/password is: admin/mysecret
SSH access
Connect the IP-PBX’s WAN port to your switch. The default ip of the WAN port is 192.168.1.100.
SSH is the advance way to access the device, you can use putty software to access the device. In
the SSH access, you can access the Linux OS and do more advance setting and debug.
The SSH user/password is: root/12xerXes06
Note: when you enter the password in putty, the password won’t show the password in shadow
or clear text. It just show nothing.
This is what you can see from putty access. Here you can enter the Linux command and do
advance configure.
Console access
The console access is very useful when you can’t access to the device from your network.
There is a console port module of IP-PBX for console access. You need a RS232 console cable to
connect to the IP-PBX, below are the connections pictures for console access.
IP04:
Below is the console port setting to access the IPXX
Running the Hyper Terminal, Putty or Minicom in your computer to connect the IP-PBX, the
setting of the console port should be:
Bits per second to 115200;
Data bits : 8
Parity: None
Stop bits: 1
Flow control: None
How to change the IP address
The default IP the IP-PBX is 192.168.1.100. Your network may have a different IP range such as
192.168.10.xx. In this case, you will not be able to configure the IP-PBX if you put it directly into
your LAN. You can change the ip address of IP-PBX to make it in the same network segment as
your LAN.
Steps:
1) Connect the IP-PBX’s WAN port to your PC.
2) Use putty to access to the IP-PBX via SSH.
3) Run below Linux command to change the IP-PBX’s IP to fit your network.
root:~> ifconfig eth0 IP_Address
replace IP_Address with a valid IP in your LAN ( if your LAN has the ip segment 192.168.10.xx,
then you will properly put 192.168.10.100 here)
4) After Step 3) is done, the IP-PBX will have a temporary IP but it will lose change after reboot.
To change its IP permanently you need to change the IP from the Web GUI. The page to
configure the IP address is:
Go to Options--> Advance Options-->Show Advance Options. Then you can find the network
settings in the main menu.
There are three types for network settings:
a) DHCP: Yes IP04 will obtain the dynamic IP from your router.
b) DHCP: auto IP04 will use the static IP specified below and ping the default gateway,
when there is no response from the default gateway. The IP04 will switch to dynamic
obtain the IP from your router.
c) DHCP: No IP04 will use the static IP specified below.
Set up extensions and make internal calls
Create extensions:
Making internal calls are the base requirement for a telephony system. You can create extensions
in the IP-PBX and use the IP phone and softphones to register to the IP-PBX and make calls.
System Setup
At the beginning, we need to add some extensions to make internal calls. Each extension acts as
an internal number. There are three types of extensions we can add: SIP, IAX2 and ZAP.
Before set up the extensions, we need to go to the Options --> General Preferences to set the
user extensions range. The default user extensions range is from 6001~6299.
Steps:
1Go to page Dial Plan-->Create New Dialplan to create a default Dial Plan.
2Go to page Users-->Create New User to create the extensions: 6001
After the extensions are created, you can use SIP terminal (IP phones/softphone/ATA etc.) to
register to the extension to make calls.
Example: Use AT-610 to register to the IP-XX and make internal call
1) Use the info key in the AT-610 to get the ip address of AT-610.
2) Put the IP address you get in your web browser to open the AT-610, the default
password is admin/admin
3) Click the Voip page
4) Put the account information you get from IP-PBX in the AT-610.
The field you should put is:
Server Address: put the ip of your IP-08
Account name: the extension number of your account in IP08
Password: the password of your extension number.
Click Enable register.
Apply the setting and you should see the AT-610 register status change to Registered.
Configure several AT-610 via the same method and every of them have an extension
number. They can call each other via the extension number.
How to make calls via the FXO port
Make outbound calls to PSTN
There are many kinds of trunk you can use to make outgoing calls. It includes: Analog FXO trunk,
Digital E1/T1/BRI Trunk, SIP trunk, IAX trunk etc. Here we use the FXO port to make outgoing
calls.
Analog/FXO trunk
For the IP01/04/08, you can install FXO module and use the FXO port to make outgoing call via
your local PSTN line. The set up is as per below:
Step 1: Create FXO trunk
Go to page Trunks--> Add New Analog Trunk
Note: The port1 and port2 of IP-PBX are slotted with FXO modules. Always click "Apply Changes"
in the right top corner when you do some changes.
Indice
Altri manuali ATCOM Centralino
ATCOM
ATCOM IPPBX IP4G Manuale utente
ATCOM
ATCOM IPPBX IP08 Manuale utente
ATCOM
ATCOM IPPBX IP4G Manuale utente
ATCOM
ATCOM APBX IP4G Manuale utente
ATCOM
ATCOM IPPBX IP01 Manuale utente
ATCOM
ATCOM IPPBX IP04 Manuale utente
ATCOM
ATCOM IPPBX IP02 Manuale utente
ATCOM
ATCOM IPPBX IP04 Manuale utente
ATCOM
ATCOM IPPBX IP02 Manuale utente
ATCOM
ATCOM IPPBX IP-2G4A Manuale utente
Manuali Centralino popolari di altre marche
Rauland-Borg
Rauland-Borg Telecenter IV Manuale utente
Grandstream Networks
Grandstream Networks UCM6208 Manuale utente
Panasonic
Panasonic KX-TVS50 - 2 Port Voicemail System Manuale utente
bintec elmeg
bintec elmeg elmeg hybird 600 Manuale utente
Panasonic
Panasonic KX-NS300 Manuale utente
MCK
MCK EXTender PBXgateway Manuale utente
