Atop ABLELink SE5001 Manuale utente
SE5001 Ethernet Serial Server
Quick Start Guide
Version 1.5
September 2011
Tel: 886-3-5508137
Fax: 886-3-5508131
http://www.atop.com.tw
Quick Start Guide Version 1.5
SE5001 Ethernet Serial Server
Copyright © 2011 Atop Technologies, Inc.
All rights reserved. Designed in Taiwan.
1
This document is intended to provide customers with brief descriptions on the product and to assist
customers to get started. For detail information and operations of the product, please refer to the user’s
manual in the product CD.
1.Packaging
Please check your package contains the following items:
SE5001 Series Serial Server
Quick Start Guide
Product CD
Wall mounting screws
3 pin terminal block for power input
5-pin terminal block with lock*1 (SE5001-S5is or SE5001-S5-TB only)
Optional Accessories
Name
Part Number
Description
DK-25
30200000000022G
DIN-Rail Kit
UN305-0510(US-DC)
50500051500001G
DC jack (1.35/3.5/7.5 mm) power adaptor,
100-240VAC input, 1.0A @ 5 VDC output, US plug
UNE305-0510(EU-DC)
50500051500011G
DC jack (1.35/3.5/7.5 mm) power adaptor,
100-240VAC input, 1.0A @ 5 VDC output, EU plug
US315-12(US-TB3)
70100000000027G
3-pin Terminal block (5.08 mm) power adaptor,
100-240VAC input, 1.25A @ 12VDC output, US plug
USE315-12(EU-TB3)
70100000000028G
3-pin Terminal block (5.08 mm) power adaptor,
100-240VAC input, 1.25A @ 12VDC output, EU plug
2.Hardware Setup
SE5001/SE5001-S2/SE5001-S5
SE5001-S5is (with isolation)
Figure 2.1. SE5001 Series Interface
LED Indicators:
Quick Start Guide Version 1.5
SE5001 Ethernet Serial Server
Copyright © 2011 Atop Technologies, Inc.
All rights reserved. Designed in Taiwan.
2
LAN LED
Message
Description
Off
Ethernet Disconnected
Blinking with Green
Data is transmitting on Ethernet for 100Mbps
Blinking with Orange
Data is transmitting on Ethernet for 10Mbps
COM Port LED
Message
Description
Off
No data is transmitting on COM port
Blinking
Data is transmitting on COM port
RUN LED
Message
Description
On
AP firmware is disabled
Blinking (rate: 0.5 Sec)
AP firmware is running normally
Installation Procedures:
Step 1: Step 1: Connect SE5001 to a power source using its 5V DC Jack or its 9-30V DC Terminal
Block. Note that the DC Jack is 5V only and should be used with a power adaptor.
Step 2:Connect SE5001 to the Ethernet network. Use a standard straight-through Ethernet cable when
connecting to a hub/switch. To simply the setup, a cross-over Ethernet cable can be used to
connect the serial device server to a PC directly.
Step 3: Connect SE5001’s serial port to a serial device.
Step 4: Placement options: Mount SE5001 to a wall/panel (Mounting screws included) or Din-Rail rack
(Din-Rail-Kit DK-25).
3. Software Setup
Default Network Setting:
Default User Name/Password:
IP: 10.0.50.100
User Name: admin
Gateway: 10.0.0.254
Password: null (leave it blank)
Subnet: 255.255.0.0
Auto IP (Dynamic IP):
A DHCP server can automatically assigns the IP address and network settings. SE5001 supports the
DHCP function. By default, the DHCP function on SE5001 is disabled; you can use SerialManager to
enable this function (refer to Figure 3.1).
Figure 3.1. SerialManager utility Dialog Window
Quick Start Guide Version 1.5
SE5001 Ethernet Serial Server
Copyright © 2011 Atop Technologies, Inc.
All rights reserved. Designed in Taiwan.
3
Assign a Static IP address by:
A. Using Telnet
1. Make sure the PC is on the same network subnet as SE5001
2. Telnet to SE5001 using DOS command “Telnet IP_address”. Example: telnet 10.0.50.100
3. SE5001’s network, link mode and COM ports settings can be configured in the telnet window
B. Using SerialManager Utility
Use SerialManager which comes inside the Product CD to automatically search for all SE5001
connected to the LAN. Select the desired SE5001 to configure the network setting individually.
C. Using Web Browser
1. Make sure the PC is on the same network subnet as SE5001.
2. Open a web browser. Type in the IP address of SE5001 to be configured. Default user name is
admin and default password is null (leave it blank).
3. SE5001’s network, link mode and COM ports settings can be configured in different web pages.
4. Click “Save Configuration” to save settings.
5. Click ”Restart” button to make the change effective if necessary.
4. Pin Assignments
The pin assignments of DB9 connector is shown in the following table:
Pin#
RS-232
Full Duplex
2-Wire RS-485
Half Duplex
RS-422/4-Wire RS-485
Full Duplex
1
DCD
N/A
N/A
2
RXD
N/A (reserved)
TXD+
3
TXD
DATA+
RXD+
4
DTR
N/A
N/A
5
SG (Signal Ground)
SG (Signal Ground)
SG (Signal Ground)
6
DSR
N/A
N/A
7
RTS
DATA-
RXD-
8
CTS
N/A(reserved)
TXD-
9
N/A
N/A
N/A
The pin assignments of Terminal Block connector is shown in the following table:
Pin#
RS-422/4-Wire RS-485
Full Duplex
2-Wire RS-485
Half Duplex
1
T+
NC
2
T-
NC
3
R+
Data+
4
R-
Data-
5
SG (Signal Ground)
SG (Signal Ground)
Customer Services and Supports
1. Contact your local dealers or Atop Technical Support Center at the following numbers.
+886-3-550-8137 (Atop Taiwan)
+86-21-6495-6232 (Atop China)
2. Report the errors via Atop’s Web site or E-mail account
www.atop.com.tw, service@atop.com.tw
www.atop.com.cn, service@atop.com.cn
Altri manuali per ABLELink SE5001
1
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali Atop Server
Atop
Atop SW5502C Manuale utente
Atop
Atop ABLELink SE5408 Manuale utente
Atop
Atop ABLELink GW51C-MAXI-WDT Manuale utente
Atop
Atop ABLELink GW51C-MAXI Manuale utente
Atop
Atop ABLELink GW21R Manuale utente
Atop
Atop PG5916 Manuale
Atop
Atop ABLELink GW21C-MAXI Manuale utente
Atop
Atop ABLELink SE5404 Series Manuale utente
Atop
Atop ABLELink GW21 MAXI Series Istruzioni operative
Atop
Atop SW550 Series Manuale
Atop
Atop ABLELink GW51C-MAXI Manuale utente
Atop
Atop SE59 Series Manuale utente
Atop
Atop Smart Security IS150 Manuale utente
Atop
Atop PG5916 Manuale
Atop
Atop ABLELink GW21W Manuale utente
Atop
Atop ABLELink GW51C-MAXI Manuale utente
Atop
Atop ABLELink GW21C-MAXI Manuale utente
Atop
Atop SW5501 Manuale utente
Atop
Atop SE59 Series Manuale utente
Atop
Atop ABLELink GW51W-MAXI Manuale utente
