AudioCodes Mediant 500L MSBR Manuale utente

1 |Page

Mediant 500L Gateway and E-SBC

Quick Setup Guide

Welcome

Congratulations on purchasing your AudioCodes Mediant 500L Gateway and Enterprise Session Border

Controller (hereafter, referred to as device)!

This document is only intended to provide basic setup instructions for initial access to the device and

connecting it to your network. For advanced configuration and cabling, refer to the User's Manual and

Hardware Manual respectively, which can be downloaded from AudioCodes Website at

https://www.audiocodes.com/library/technical-documents.

Before you begin, please read the Safety Precautions on page 7.

Package Contents

Make sure that the following items (in addition to any separate-orderable items that you may have purchased)

are included with your shipped device:

4 x anti-slide bumpers for desktop mounting

1 x AC/DC power adapter

Regulatory Information document

This document

2 |Page

Physical Description

[The number and type of port interfaces depend on the ordered hardware configuration.]

POWER

AC power plug entry

Power LED (located on the front panel):

Green On

Power received by device

Off

No power

Status LED (located on the front panel):

Green On

Device is operational

Green Flashing

Initial rebooting stage or software upgrade (.cmp

file) in process

Red On

Boot failure

Off

Advanced rebooting stage

ON / OFF

Power button to switch on the device (when pressed in) and to switch off the

device (when pressed out).

CONSOLE

RS-232 serial interface port (RJ-45).

USB port, which you can use for various functionalities such as storing the

configuration file on an external USB hard drive.

Reset pinhole button for resetting the device or restoring it to factory defaults. To

restore the device to factory defaults: with a paper clip or any other similar

pointed object, press and hold down the button for at least 12 seconds (but no

more than 25 seconds).

S1 GE LAN

Up to four Gigabit Ethernet (10/100/1000Base-T) ports (RJ-45) for connecting IP

phones, computers, or switches. The ports support 1+1 Ethernet port redundancy

(active-standby), half- and full-duplex modes, auto-negotiation, and straight-

through or crossover cable detection.

Green On

Ethernet link established

Green Flashing

Data is being received or transmitted

Off

No Ethernet link

3 |Page

Mounting the Device

You can mount the device in several ways:

Placing it on a desktop using the four anti-slide bumpers (supplied), which you need to stick on the

grooves located on the underside of the device.

Mounting it in a standard 19-inch rack by placing it on AudioCodes 1U 19-inch rack mount shelf

(separate orderable item). The procedure includes attaching the shelf to the rack's front posts, and

then placing the device on the shelf where it is securely held in position by the device's anti-slide

bumpers which fit into the shelf's four square-openings.

Mounting it on a wall, using the integral mounting keyholes located on its underside.

For detailed instructions on mounting, refer to the Hardware Manual.

4 |Page

Cabling the Device

The device is powered by an external 12V/3A AC/DC power adapter (supplied), connected to a standard

alternating current (AC) electrical wall outlet.

1. The AC/DC power adapter (supplied) supports interchangeable plugs to suit the type of electrical wall

outlet of the country in which you are installing the device. To attach the required plug to the adapter,

insert the top part of the plug into the upper part of the adapter's housing slot, and then press down

on the bottom part of the plug until you hear a "click" sound, indicating that the plug is securely

inserted into the slot. (To remove the plug, push and slide down the adapter's OPEN plug release

lever.)

2. Insert the DC plug that is located at the end of the power cord of the power adapter into the device's

power socket located on the rear panel and labeled POWER.

3. Plug the power adapter directly into a standard electrical wall outlet.

4. Switch on the device by pressing-in the power button located on the rear panel. When the device

receives power, the Power LED turns on (green).

5 |Page

Assigning an IP Address to the Device

Use the device's factory default IP address (192.168.0.2/24 and Default Gateway 0.0.0.0) to initially access the

device's Web-based management interface and then change it to suit your networking addressing scheme for

subsequent connectivity.

1. Using a CAT-5e/6 straight-through RJ-45 Ethernet cable, connect the device's Ethernet port GE LAN #1

(front panel) to the LAN port of your computer.

2. Change the IP address of your computer to correspond with the device's default IP address and subnet

mask.

3. On your computer, open a standard Web browser (for example, Google Chrome), and then in the URL

field, enter the device's default IP address; the Web Login screen appears:

4. Type in the default username (Admin) and password (Admin), and then click Login.

5. Open the IP Interfaces table (Setup menu > IP Network tab > Core Entities folder > IP Interfaces).

6 |Page

6. Select the OAMP interface ('Application Type' with OAMP + Media + Control), click Edit, and then in

the dialog box, modify the device's OAMP interface.

7. Click Apply to submit your changes.

8. On the toolbar, click Reset to access the Maintenance Actions page.

9. On the Maintenance Actions page, click Reset to save your new settings to flash memory with a device

reset.

10. Disconnect the device's Ethernet cable from the computer and connect it to your network.

11. Access the device's management interface using the new IP address that you assigned the device.

7 |Page

Safety Precautions

This device is an indoor unit and therefore, must not be installed outdoors.

Ethernet cabling must be routed only indoors and must not exit the building.

The device must be installed and serviced only by qualified service personnel.

Do not open or dismantle the device.

Do not expose the device to water or moisture.

Make sure the device is installed in a well-ventilated location to avoid over heating of internal

components and subsequent damage.

Do not place any object on top of the device and make sure that sufficient clearance from the top and

sides are maintained to ensure proper airflow to avoid over heating of internal components.

Operate the device in an ambient temperature (Tma) that does not exceed 40°C (104°F).

The device must be installed only in restricted access locations.

Use only the supplied AC/DC power adapter for connection to the power source.

In case of a malfunction, do not attempt to fix the power adapter and do not use any other type of

power adapter. Contact AudioCodes for further assistance.

Operate the device only from the type of power source indicated on the chassis.

Installation of the device must be in accordance with national electrical codes and conform to local

regulations.

Use minimum 26-AWG wiring for FXO ports.

8 |Page

About AudioCodes

AudioCodes Ltd. (NasdaqGS: AUDC) is a leading vendor of advanced voice networking and media processing

solutions for the digital workplace. With a commitment to the human voice deeply embedded in its DNA,

AudioCodes enables enterprises and service providers to build and operate all-IP voice networks for unified

communications, contact centers and hosted business services. AudioCodes’ wide range of innovative

products, solutions and services are used by large multinational enterprises and leading tier one operators

worldwide.

International Headquarters

1 Hayarden Street,

Airport City

Lod 7019900, Israel

Tel: +972-3-976-4000

Fax: +972-3-976-4040

AudioCodes Inc.

27 World’s Fair Drive,

Somerset, NJ 08873

Tel: +1-732-469-0880

Fax: +1-732-469-2298

Website: https://www.audiocodes.com/

MediaPack, What’s Inside Matters, OSN, SmartTAP, User Management Pack, VMAS, VoIPerfect, VoIPerfectHD, Your

Gateway To VoIP, 3GX, VocaNom, AudioCodes One Voice and CloudBond are trademarks or registered trademarks of

AudioCodes Limited. All other products or trademarks are property of their respective owners. Product specifications are

subject to change without notice.

Document #: LTRT-10702

Altri manuali per Mediant 500L MSBR

Indice

Altri manuali AudioCodes Portale

AudioCodes

AudioCodes Commander MP264DB Manuale utente

AudioCodes

AudioCodes Mediant 500L MSBR Manuale utente

AudioCodes

AudioCodes MediaPack 504 Istruzioni per il montaggio

AudioCodes

AudioCodes Mediant 800B Manuale utente

AudioCodes

AudioCodes Mediant 800B Manuale utente

AudioCodes

AudioCodes MediaPack MP-1 Series Manuale utente

AudioCodes

AudioCodes Mediant 600 Manuale utente

AudioCodes

AudioCodes Mediant 1000B Manuale utente

AudioCodes

AudioCodes Mediant 500 E-SBC Manuale utente

AudioCodes

AudioCodes M500L Istruzioni per il montaggio

AudioCodes

AudioCodes Mediant 3100 Istruzioni per il montaggio

AudioCodes

AudioCodes Mediant 800B Manuale utente

AudioCodes

AudioCodes MediaPack MP-402 Manuale utente

AudioCodes

AudioCodes MediaPack 1288 Manuale utente

AudioCodes

AudioCodes MP-104 Manuale utente

AudioCodes

AudioCodes MP-11x Fast Track Manuale utente

AudioCodes

AudioCodes Media Pack MP-11x Manuale utente

AudioCodes

AudioCodes Mediant 3000 Manuale utente

AudioCodes

AudioCodes Mediant 800B Manuale utente

AudioCodes

AudioCodes MediaPack MP-264 Manuale utente

AudioCodes

AudioCodes Mediant 2000 Istruzioni per il montaggio

AudioCodes

AudioCodes MediaPack MP-114 Manuale utente

AudioCodes

AudioCodes Mediant 800B Manuale utente

AudioCodes

AudioCodes Mediant 800B Manuale

Manuali Portale popolari di altre marche

LST

LST M500RFE-AS Manuale utente

Kinnex

Kinnex Media Gateway Manuale utente

2N Telekomunikace

2N Telekomunikace 2N StarGate Manuale utente

Mitsubishi Heavy Industries

Mitsubishi Heavy Industries Superlink SC-WBGW256 Manuale utente

ZyXEL Communications

ZyXEL Communications ZYWALL2 ET 2WE Manuale utente

Telsey

Telsey CPVA 500 - SIP Manuale utente

RTA

RTA 460A-NNA4 Scheda tecnica

Shaw

Shaw Gateway HDPVR Manuale utente

ABB

ABB VSN900 Guida rapida

Commander

Commander Pulse Manuale utente

2N Telekomunikace

2N Telekomunikace ATEUS EasyGate 501309E Manuale utente

NETGEAR

NETGEAR C6300BD Manuale utente

Amit

Amit CDW531AM Manuale utente

HMS

HMS Netbiter EasyConnect EC150 Manuale utente

Huawei

Huawei EchoLife HG620 Manuale utente

AT&T

AT&T U-verse 3801 Manuale per l'uso e la cura

Logic IO

Logic IO RTCU MX2 turbo Manuale utente

Suttle

Suttle MediaMAX MXM-521 Manuale utente