Audiovox AA-95BT3S Istruzioni operative
TRANSMITTER SYSTEM RECEIVER
CHANNEL BUTTONS CHANNEL FUNCTION
1 1 1 Remote Arm & Disarm
*Remote Emergency Panic
*Remote Door Lock & Unlock
2 2 2 Push And Hold For 3 Seconds For Trunk
Release, Push 2 Times For Remote Start.
** Pulsed Output for Accessories
3 3 3 ** Switched Output for Accessories
4 1&2 4 -
5 2&3 - -
6 1&3 - -
7 1&2&3 - -
* Remote Emergency Panic is available only on certain models.
* Door Lock/Unlock may require additional components in certain vehicles.
** Some of the more common accessories for these additional channels are;
AS 9153 Remote window roll up
AS 9256 Remote trunk release relay
123
TRANSMITTER PROGRAMMING GUIDE
Model : AA95BT3/AA-95BT3S
The transmitters included with the system have been pre-programmed at the
factory,witheachbuttonpre-assignedtocontrolaspecificfunctionofthesystem.
Although the system in the vehicle has either a 2, 3 or 4 channel RECEIVER,
dependingonthemodel,thetransmittersincludedwiththesystemare7channel
transmitters. This allows you to program each transmitter to more than one
vehicleintwocarfamilies,andalsoallowsyoutochangewhichbuttonorbuttons
controlcertainfunctionsofthesystem.(Example:Transmitterchannel5,shown
below, can be programmed to activate Receiver channel 2.) Refer to the chart
belowforaccesstoeachofthetransmitterchannels,andforthestandardfactory
button assignments.
PROGRAMMING THE TRANSMITTERS
Itisimportant to remember that during programming,eachindividual step of the
procedure must be executed within 15 seconds of the previous step.
Whenthe15secondtime limit is allowed to expire, the system will automatically
terminatetheprogrammingmode.Thisisindicatedbyalongchirpfromthesiren.
Additionally, the system will store codes from up to four different transmitters. If
a5thtransmitterisprogrammedtoanyreceiverchannel,thenthefirsttransmitter
programmed to that channel will be erased from the system's memory.
Note: TheLED,andsirenreferencedbelowmaynotbeavailableonallmodels.
In these cases, where siren is referenced, the parking lights will instead
flash.
To program new or additional transmitters,
1. Enter the vehicle, and turn the ignition key to the " on " position.
2. Flip the valet/program switch on - off - on - off - on - then off.
3. The dash LED will flash one time, and the siren will chirp one time, indicating
the system is ready to accept programming for receiver channel 1.
4. Pressandholdtheselectedtransmitterbutton(s)untilthesirensoundsalong
chirp, indicating the signal has been stored into memory.
5. If you have additional transmitters ( up to 3 ) that need to be programmed,
repeat step 4 for each transmitter.
6. Flip the valet/program switch on then off.
7. ThedashLEDwillflashtwotimes,andthesirenwillchirptwotimes,indicating
the system is ready to accept programming for receiver channel 2.
8. Pressandholdtheselectedtransmitterbutton(s)untilthesirensoundsalong
chirp, indicating the signal has been stored into memory.
9. If you have additional transmitters ( up to 3 ) that need to be programmed,
repeat step 8 for each transmitter.
10. Flip the valet/program switch on then off.
11. The dash LED will flash three times, and the siren will chirp three times,
indicatingthesystemisreadytoacceptprogrammingforreceiverchannel3.
12. Press and hold the selected transmitter button ( s ) until the siren sounds a
long chirp, indicating the signal has been stored into memory.
13. If you have additional transmitters ( up to 3 ) that need to be programmed,
repeat step 12 for each transmitter.
14. Flip the valet/program switch on then off.
15. The dash LED will flash four times, and the siren will chirp four times,
indicating the system is ready to accept programming for receiver channel 4.
16. Press and hold the selected transmitter button ( s ) until the siren sounds a
long chirp, indicating the signal has been stored into memory.
17. If you have additional transmitters ( up to 3 ) that need to be programmed,
repeat step 16 for each transmitter.
18. Turn the ignition key off. The siren will sound one short chirp then one long
chirp indicating the system has terminated the program mode.
NOTE: Some systems have only 2 or 3 programmable receiver channels. If
duringtheprogramsteps11orstep15,thesirenemittedshortthenlong
chirp indicating the transmitter program mode has been exited, this
indicates you system has either 2 or 3 receiver channels.
BATTERYREPLACEMENT:
Thetransmitterincorporatesa smallLEDseenthroughthecase lens. ThisLED
can be used to indicate battery condition. You will notice a decrease in
transmitterrangeasthe battery condition deteriorates. To replace the battery...
1. Removethetransmittercoverbyremovingthetwosmallscrewfromtheback
of the transmitter case.
2. Carefully unsnap the top cover of the transmitter from the bottom cover.
3. Removethedischargedbattery,makingnoteofthe
orientation of the + and - contacts, and dispose of
properly. Install the new (type GP23A) battery,
taking care to orient the + and - contacts properly.
4. Replace the transmitter cover, taking care not to
damage the LED or switches on the circuit board.
Reinstall the case screws. You will notice a
decrease in transmitter range as the battery
condition deteriorates. Transmitter battery
replacement is recommended at least every 10
to 12months,dependinguponhowfrequentlythe
transmitter is used.
IMPORTANT: Tohelpusexpediteyourorder,pleaseprintalloftheinformation
legibly, and mail this form and your payment according to the
instructions below.
NOTE: The AA-95BT3 and AA-95BT3S transmitters both use the same
programming guide. To insure you receive the proper replacement
transmitter, locate the correct model number on the back of the
transmittercase. Circlethepropermodelwhenorderingeitherofthese
transmitters.
1. Name : ___________________________________________________
Address : _________________________________________________
City : __________________ State : _______ Zip Code : ___________
2. Telephone Number : ( _______ ) _______________________________
3. Enter the total number of transmitters required here : _______________
4. The cost per transmitter is $ 65.00.
5. Enter the total amount enclosed here : __________________________
(New York state residents must include the appropriate sales tax. )
6. Method of payment; check one of the boxes below.
qMastercard qVisa qCheck or money order * ( do not send cash )
* Make checks payable to Audiovox Corporation
7. Credit Card Number : ________________________________________
8. Credit Card Expiration Date : _____________________
Credit card purchasers can order additional or replacement
transmittersbyphone.Simplydial 1 -800-645-4994,andfollow
the instructions from the operator interface.
9. Mail this form, and your check, to ;
(
128-5815
Audiovox Electronics Corp., 150 Marcus Blvd. Hauppauge, N.Y., 11788
Attn.:TRANSMITTERDEPARTMENT
ORDER FORM FOR 3 BUTTON TRANSMITTER
MODEL NO. AA95BT3/AA-95BT3S
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Audiovox Trasmettitore
Audiovox
Audiovox 128-5971 Istruzioni per il montaggio
Audiovox
Audiovox ADDP1 Istruzioni operative
Audiovox
Audiovox Prestige APS-2K4 Istruzioni operative
Audiovox
Audiovox Pursuit OE3-FT3 Istruzioni operative
Audiovox
Audiovox A1BTX Istruzioni operative
Audiovox
Audiovox Prestige APS-92BT-CL Guida alla risoluzione dei problemi
Audiovox
Audiovox Pursuit PRO-OE2 Istruzioni operative
Audiovox
Audiovox Prestige 103BP Istruzioni operative
Audiovox
Audiovox PRO-OE3B370 Istruzioni operative
Audiovox
Audiovox PRO94BT3 Istruzioni operative
Audiovox
Audiovox AA-99BT2 Istruzioni operative
Audiovox
Audiovox 5BCR03A Istruzioni operative
Audiovox
Audiovox APS 95 BT3S Istruzioni operative
Audiovox
Audiovox PurSuit 08SPr Istruzioni operative
Audiovox
Audiovox PRO-94FR Istruzioni operative
Audiovox
Audiovox Prestige 07S1BP Istruzioni operative
Audiovox
Audiovox Pursuit PRO-OE4 Istruzioni operative
Audiovox
Audiovox PurSuit 09XR1Pr Istruzioni operative
Audiovox
Audiovox AVX01BT3CL3 Istruzioni operative
Audiovox
Audiovox AX-2K4 Istruzioni operative
