Audiovox AVX01BT3CL3 Istruzioni operative

128-6105

1 of 6

Model AVX01BT3CL3

Released 7-25-01.

TRANSMITTERPROGRAMMINGGUIDE

The transmitters included with the system have been pre-programmed at

the factory, with each button pre-assigned to control a specific function of

thesystem.Althoughthesysteminthevehiclehaseithera3,4,or5channel

RECEIVER, depending on the model, the transmitters included with the

system are 7 channel transmitters. This allows you to program each

transmitter to more than one vehicle in two car families and also allows you

to change which button or buttons control certain functions of the system.

(Example: Transmitter channel 5, shown below, can be programmed to

activate Receiver channel 2.) Refer to the chart below for access to each of

the transmitter channels, and for the standard factory button assignments.

TRANSMITTER SYSTEMRECEIVER

CHANNEL BUTTONS CHANNEL FUNCTION

1 1 RemoteArm

* Remote Emergency Panic

**Remote Door Lock

2 2 RemoteDisarm

*RemoteEmergencyPanic

***Remote Unlock Drivers Door

**Remote Unlock All Doors

3 3 Push And Hold For 3 Seconds For Opt1

Release, Push 2 Times For Aux. Out.

4 4 **** Pulsed Output for Accessories

5 5 **** Switched Output for Accessories

6 - **** RF

7 - **** RF

* Remote Emergency Panic is available only on certain models.

** Door Lock/Unlock may require additional components in certain vehicles.

*** Unlock Driver Door or Unlock All Doors May Require Additional Components

**** Some of the more common accessories for these additional channels are;

AS 9075 Remote Car Starter

AS 9256 Remote Trunk Release Relay

AS 9154 Remote Garage Door Interface

AS 9153 Remote Window Roll Up

128-6105

2 of 6

PROGRAMMINGTRANSMITTERS:

Itisimportanttorememberthatduring programming, each individual step of

the procedure must be executed within 15 seconds of the previous step.

When the 15 second time limit is allowed to expire, the system will

automaticallyexitprogrammode. Thisisindicatedbyalong"chirp"fromthe

siren.

Additionally, any time the ignition key is turned off while programming, the

systemwill immediately exit program mode. Thisis also indicated by along

"chirp" from the siren.

These steps must be initiated within 15 seconds of the ignition switch being

turned on.

TOPROGRAMADDITIONALTRANSMITTERS:

Note: The programming information described below assumes that the

defaulttransmitterisbeingusedandtheLock&Unlockiconsareonseparate

buttons. If you have the optional transmitter with the Lock/Unlock icon on

the same button, use letter "B" reference below for programming, (B

programming not available on all models),

Also, where indicated that the siren will emit a long chirp tone, the optional

horn may be connected instead of or along with the siren in which case

either or both the horn and siren may sound.

If the system you have is a keyless entry unit and not an alarm, there may

be no sounding device.

For units with a toggle switch instead of a pushbutton switch, where

indicated to press and release the pushbutton, instead move the toggle

switch on then off.

1. (a) Enter the vehicle and turn the ignition key to the "on" position.

(b) Enter the vehicle and turn the ignition key to the "on" position.

2. (a) Press and release the valet/bypass push button switch 3 times.

(b) Press and release the valet/bypass push button switch 3 times.

3. (a) The dash LED will flash one time, and the siren will "chirp" 1 time

indicating the system is ready to accept programming for channel 1,

Arm/Lock and Panic.

(b) The dash LED will flash one time and the siren will "chirp" 1 time

indicating the system is ready to accept programming for channel 1,

Arm/Disarm, Lock/Unlock and Panic.

4. (a) YoucanassigntheLock/Armbuttonbypressingandholdingthelock

button until the siren emits a long chirp tone.

128-6105

3 of 6

Thechirptoneconfirms that programmingofchannel1wassuccessful.

Upto4transmitterscanbeprogrammed,pressandholdtheselected

button of each additional transmitter until the chirp tone is heard, or

move to step #5

(b) You can assign the Lock/Unlock, Arm/Disarm button, by pressing

and holding the lock/unlock button until the siren emits a long chirp

tone.

The chirp tone confirms that programming of channel 1 was

successful.Upto4 transmitters canbeprogrammed, press and hold

the selected button of each additional transmitter until the chirp tone

is heard, or press and release the valet pushbutton switch two times

to advance to step #8.

5. Press and release the valet/override switch one time to advance to

channel 2.

6. (a) The dash mounted LED will flash 2 times, and the siren will "chirp"

2timesindicating thatthesystemisreadytoacceptprogrammingfor

channel 2. Unlock/2nd Unlock, Disarm, and Panic. Press and hold

the Unlock button on your keychain transmitter until the siren emits

a long chirp tone. This confirms that programming of channel 2

was successful. Up to 4 transmitters can be programmed, press

and hold the selected button of each additional transmitter until the

chirp tone is heard.

(b) Press and release the valet/override switch 1 time then move onto

step #7 or.

7. Press and release the valet/override switch one time to advance to

channel 3.

8. The dash mounted LED will flash 3 times, and the siren will "chirp"

3 times, indicating that the system is ready to accept programming

for channel 3. Trunk Release Output, (where so equipped), or

alternate channel output when used.

9. (a) Press and hold the Opt. button on your keychain transmitter until the

siren emits a long chirp tone. This confirms that programming of

channel 3 was successful. Up to 4 transmitters can be programmed,

pressandholdtheselectedbuttonofeachadditionaltransmitteruntil

the chirp tone is heard.

(b) Press and hold the 1st Opt. button on your keychain transmitter until

the siren emits a long chirp tone. This confirms that programming of

channel 3 was successful. Up to 4 transmitters can be programmed,

pressandholdtheselectedbuttonofeachadditionaltransmitteruntil

the chirp tone is heard.

128-6105

4 of 6

After the desired channel is programmed, turn the ignition key to the off

position to exit programming mode.

VALETSWITCH

Press and Release 3 Times

Press and Release 4 Times

Press and Release 5 Times

Press and Release 6 Times

LED

1 Flash

2 Flashes

3 Flashes

4 Flashes

10. Press and release the valet/override switch one time to advance to

channel4ifsoequipped. Ifyoursystemdoesnothavea4thchannel,

a long chirp followed by a short chirp tone will indicate that the

program mode has been exited.

11. ThedashmountedLED willflash4times andsirenwill"chirp"4times

indicating that the system isready to accept programming of channel 4.

12. (a)Press and hold any combination of two buttons simultaneously, until

the siren emits a long chirp tone. This confirms that programming of

channel 4 was successful. Up to 4 transmitters can be programmed,

pressandholdtheselectedbuttonofeachadditionaltransmitteruntil

the chirp tone is heard.

(b)Press and hold the remaining Opt. button of the transmitter until the

siren emits a long chirp tone. This confirms that programming of

channel4 was successful. Upto4 transmitters canbe programmed,

pressandholdtheselectedbuttonofeachadditionaltransmitteruntil

the chirp tone is heard.

orpress and releasethe push buttonswitch to exitthe programming

mode,

or turn the ignition switch off to exit the programming mode.

The siren emits a long followed by a short chirp tone indicating that the

program mode has been exited.

NOTE: If programming to a Keyless Entry (non alarm) unit, there will be

NO chirp indication.

QUICKREFERENCE:

You can program any individual channel, without reprogramming all

channels, byfollowing the quick referencechart below. (Not All Units Have

4 Channels)

CHANNEL

128-6105

5 of 6

BATTERYREPLACEMENT:

Thetransmitter incorporates a small red LED visiblethrough thecase. This

LED can be used to indicate battery condition. You will notice a decrease

in transmitter range as the battery condition deteriorates. Transmitter

battery replacement is recommended at least every 10 to 12 months,

depending upon how frequently the transmitter is used.

To replace the battery...

1. Removethetransmittercoverbyremovingthesmallscrewfromtheback

of the transmitter case.

2. Remove the discharged battery, making note of the orientation of the +

and - contacts, and dispose of properly.

3. Install the new (type GP23A) battery, taking care to orient the + and -

contacts properly.

4. Replace the transmitter cover, taking care not to damage the LED or

switches on the circuit board.

128-6105

6 of 6

IMPORTANT: To help us expedite your order, please print all of the

information legibly, and mail this form and your payment according to the

instructions below. Please indicate which button pad is used with your

transmitter as indicated above.

Transmitter model number is found on rear case.___________________

1. Name : _________________________________________________

Address : __ ___________________________________________

City : ___________________ State : ______ Zip Code : __________

2. Telephone Number : (________) _____________________________

3. Enter the total number of transmitters required here : _____________

4. The cost per transmitter is $ 65.00.

5. Enter the total amount enclosed here : ________________________

( New York state residents must include the appropriate sales tax. )

6. Method of payment; check one of the boxes below.

Mastercard Visa Check or money order * (do not send cash)

* Make checks payable to Audiovox Corporation

7. Credit Card Number : ______________________________________

8. Credit Card Expiration Date : __________________________

9. Mail this form, and your check, to ;

    

   0133301333

0133301333

01333 





6060

60 6161

6161

61

  150  . , .. 11788  150  . , .. 11788

  150  . , .. 11788

:  :  

:  

Credit card purchasers can order additional or replacement

transmitters by phone. Simply dial 1 - 800 - 645 - 4994, and

follow the instructions from the operator interface.



128-6105

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Audiovox Trasmettitore

Audiovox

Audiovox PSI 95BT3 Istruzioni operative

Audiovox

Audiovox Prestige 07S1BP Istruzioni operative

Audiovox

Audiovox PRO92BTINT Istruzioni operative

Audiovox

Audiovox AUTO SECURITY Prestige OE3B4 Istruzioni operative

Audiovox

Audiovox ACA300 Manuale utente

Audiovox

Audiovox S1BTXA Istruzioni operative

Audiovox

Audiovox PRO94BT3 Istruzioni operative

Audiovox

Audiovox PurSuit 09XR1Pr Istruzioni operative

Audiovox

Audiovox Pursuit PRO-OE3 Istruzioni operative

Audiovox

Audiovox PRO94BT2 Istruzioni operative

Audiovox

Audiovox Prestige 101BP Manuale del proprietario

Audiovox

Audiovox Prestige APS-2K4 Istruzioni operative

Audiovox

Audiovox Pursuit PRO-OE4 Istruzioni operative

Audiovox

Audiovox APS 95 BT3S Istruzioni operative

Audiovox

Audiovox Pursuit PRO-OE3B3 Istruzioni operative

Audiovox

Audiovox Prestige APS-2K4MS Istruzioni operative

Audiovox

Audiovox Pursuit Series Manuale utente

Audiovox

Audiovox AX-2K4 Istruzioni operative

Audiovox

Audiovox PRO-94FR Istruzioni operative

Audiovox

Audiovox Pursuit 093BPr Istruzioni operative

Audiovox

Audiovox PurSuit 08SPr Istruzioni operative

Audiovox

Audiovox AA-95BT3S Istruzioni operative

Audiovox

Audiovox UltraGuard UG-OE3 Istruzioni operative

Audiovox

Audiovox Prestige APS-92BT-CL Guida alla risoluzione dei problemi

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente