Audiovox ACA300 Manuale utente
Wireless Transmitter and Receiver
Model:ACA300
Installation Manual
Features:
•Operating frequency: 2.4GHz.
•Converts Hard Wired Systems to Wireless
•Developed for Backup Camera Systems
•RCA Connector
Warnings
The product is intended to assist in safe driving and to allow the driver to
have a broader rearview while the vehicle is in reverse. You, as the driver,
are solely responsible for the safe operation of your vehicle and the safety
of your passengers according to the country and their local traffic
regulations. Do not use any features of this system to the extent it distracts
you from safe driving. Your first priority while driving should always be
the safe operation of your vehicle. Audiovox Electronics Corporation
cannot accept any responsibility whatsoever for accidents resulting from
failure to observe these precautions or safety instructions.
1. This product utilizes high voltage. Any unauthorized modifications
or damage to the products may result in electrical shock. Handle
all components with care. Inspect regularly for damage to
components and cabling.
anufacturer’s warranty.
warranties.
4. per
installation or modification of this product shall void all warranties.
2. You shall be responsible to ensure that the installation of this
product does not void or affect the vehicle manufacturer’s
warranty. Audiovox Electronics Corporation or its subsidiaries are
not liable in full or in part for improper installation resulting in
loss or damage to your property, or for voiding all or part of the
vehicle m
3. Do not apply excessive force to any of the components contained
within this kit. Excessive force used before, during or after installation
that results in a damaged or non-functional part shall void all
Please follow the procedure from this installation manual. Impro
1
Table of Contents
Warnings 1
Table of contents 2
Product description 2
Packing list 2
Transmitter/Receiver installation 3
Specifications 4
Troubleshooting 5
Product Description
The wireless transmitter and receiver have been developed to convert a
hard wire camera/monitor system to a wireless operation. The following
information contained in the installation manual is for camera backup
systems. Note: this product can be used on any Camera/Monitor system.
Packing List
1. Transmitter w/RCA Connector-1 qty
2. Receiver w/RCA Connector-1 qty
3. Wire connectors:
a. Tap connectors-3 qty
b. Ring connectors-1 qty
4. Installation Manual
5. Warranty Card
2
Transmitter/Receiver Installation
The transmitter and the receiver must be installed in the vehicle’s trunk or
interior. The transmitter and receiver are not weather proof and must be
located in a dry location
Ta
p
/Run Connection
a) Wiring the transmitter to the vehicle reverse lamp. Using the
tap connectors supplied.
i. Place the unstripped positive lead wire on the run channel
ii. Insert the unstripped red power wire completely
iii. Fold the tap connector back over the wires and make the
connection by crimping the u-contact down flush with the
plastic insulator.
iv. Close the top hinged cover until latched.
b) Black wire- Chassis/Ground. Using. Using the tap connectors
supplied.
i. Place the unstripped ground lead wire on the run channel
ii. Insert the unstripped black ground power wire completely
iii. Fold the tap connector back over the wires and make the
connection by crimping the u-contact down flush with the
plastic insulator.
iv. Close the top hinged cover until latched.
2. Wiring the transmitter to the camera.
a) Connect the transmitters RCA connector to the Cameras RCA
connector.
3
a. Wiring the receiver to the vehicle. Choose a source that only
has power when the vehicle is running. Connect as shown
Using the tap connectors supplied.
i. Place the unstripped ignition source wire on the run channel
ii. Place the unstripped red power wire completely
iii. Fold the tap connector back over the wires and make the
connection by crimping the u-contact down flush with the
plastic insulator.
iv. Close the top hinged cover until latched.
b. Black wire- Chassis/Ground. Using ground ring supplied,
i. Place stripped wire (1/4”) inside connector
ii. Crimp the connector using a crimping tool to secure the
wire.
Specifications:
1. Operating voltage: 11.5V-14.5V
2. Operating current:
Transmitter: 70mA
Receiver: 180mA
3. Operating frequency: 2.4GHz
4. Operating temperature: 0-50
4
Troubleshooting
Symptoms Solutions
The Monitor is not on after the
vehicle is started and vehicle is
in reverse?
Check the monitor and the receiver
wiring and connection.
No video signal appears while
reversing the vehicle?
Check the rearview Camera and the
Transmitter wiring connection.
Video image is not sharp
enough? Clean the lens of the camera.
© 2007 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788
5
Indice
Altri manuali Audiovox Trasmettitore
Audiovox
Audiovox Prestige 07S1BP Istruzioni operative
Audiovox
Audiovox Pursuit PRO-OE3B3 Istruzioni operative
Audiovox
Audiovox Prestige 103BP Istruzioni operative
Audiovox
Audiovox Pursuit PRO-OE3B4 Istruzioni operative
Audiovox
Audiovox PurSuit 08SPr Istruzioni operative
Audiovox
Audiovox PRO94BT3 Istruzioni operative
Audiovox
Audiovox 128-5971 Istruzioni per il montaggio
Audiovox
Audiovox Pursuit 095BPr Istruzioni operative
Audiovox
Audiovox PRO-OE3B370 Istruzioni operative
Audiovox
Audiovox A1BTX Istruzioni operative
Audiovox
Audiovox AA-99BT2 Istruzioni operative
Audiovox
Audiovox PRO-OE3C Guida alla risoluzione dei problemi
Audiovox
Audiovox Prestige 101BP Manuale del proprietario
Audiovox
Audiovox Auto Security SS91 Istruzioni operative
Audiovox
Audiovox PurSuit 091BPr Istruzioni operative
Audiovox
Audiovox AVX01BT3CL3 Istruzioni operative
Audiovox
Audiovox Pursuit PRO-OE3 Istruzioni operative
Audiovox
Audiovox PSI 95BT3 Istruzioni operative
Audiovox
Audiovox ADDP1 Istruzioni operative
Audiovox
Audiovox Prestige APS-92BT-CL Guida alla risoluzione dei problemi
