Avery Dennison Stacker Monarch 932TM Manuale utente
TC0932OI Rev. AC 12/07 ©2004 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved.
Operating
Instructions
Operating
Instructions
23456
78901
Fishing Tackle
$40.00
23456
78901
Fishing Tackle
$40.00
23456
78901
Fishing Tackle
$40.00
23456
78901
Fishing Tackle
$40.00
Monarch®
932™ Stacker
Each product and program carries a respective written warranty, the only warranty on
which the customer can rely. Paxar Americas reserves the right to make changes in
the product, the programs, and their availability at any time and without notice.
Although Paxar Americas has made every effort to provide complete and accurate
information in this manual, Paxar Americas shall not be liable for any omissions or
inaccuracies. Any update will be incorporated in a later edition of this manual.
©2004 Paxar Americas, Inc. a subsidiary of Avery Dennison Corp. All rights reserved.
No part of this publication may be reproduced, transmitted, stored in a retrieval system,
or translated into any language in any form by any means, without the prior written
permission of Paxar Corporation.
WARNING
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction
manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the
user will be required to correct the interference at his own expense.
CANADIAN D.O.C. WARNING
This digital apparatus does not exceed the Class A limits for radio noise emissions from
digital apparatus set out in the Radio Interference Regulations of the Canadian
Department of Communications.
Le présent appareil numérique n’émet pas de bruits radioélectriques dépassant les
limites applicables aux appareils numériques de la classe A prescrites dans le
Réglement sur le brouillage radioélectrique édicte par le ministPre des Communications
du Canada.
Trademarks
Monarch®, 932, 9855, and 9860, are trademarks of Paxar Americas, Inc.
Paxar® is a trademark of Paxar Corporation.
Avery Dennison® is a trademark of Avery Dennison Corporation.
Avery Dennison Printer Systems Division
170 Monarch Lane
Miamisburg, OH 45342
TABLE OF CONTENTS
GETTING STARTED. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Unpacking the Stacker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Installing the Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1
Step 1 - Installation for the 9860 Printer . . . . . . . . . . . . . . . . . . . . . . . 1-2
Step 2 - Level the Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
Step 3 - Connect the Power Cord . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-4
Step 4 - Check the Alignment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-5
Step 5 - Set the Tag Width. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
Step 6 - Set the Belt Speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-8
HOW TO OPERATE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1
Re-Loading or Changing Supplies. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Emptying the Stacker. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Stacker Full . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-2
Stacker Running . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Clearing a Tag Jam. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
Installing Riser Blocks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4
TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1
SPECIFICATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Stacker . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-1
Supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
Minimum Stacked Tag Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . A-2
i Table of Contents
ii Table of Contents
GETTING STARTED 1
The Monarch® 932stacker works with a Monarch® 9860
printer. The stacker supports backfeed mode on the printer. There
is no power ON/OFF switch for the stacker. Once the stacker is
plugged into an outlet, it is on.
Unpacking the Stacker
uImportant: After unpacking the stacker, look through all
packaging material for parts. Keep all packaging material
for future shipping.
Installing the Stacker
Use these instructions when you first install the stacker or when
you need to move the stacker to a different location.
Before installing:
uFind a level work surface at least 52" x 22"
(1321 mm x 559 mm).
The 9860 printer comes with a knife attached.
uTurn off the printer before you install the stacker.
Getting Started 1-1
Step 1 - Installation for the 9860 Printer
1. Locate the screw hole on the stacker mounting plate.
2. Attach the adjusting bracket to the stacker mounting plate
using a flanged screw as shown (do not tighten all the way).
3. Gently lift stacker and center the guide tabs in the knife
opening.
4. Set the stacker locating pins (on bottom of stacker) firmly in
the adjusting bracket locating hole and mounting plate slot.
5. Tighten the adjusting bracket flanged screw.
6. Connect the stacker cable to the knife.
Stacker
Mounting
Plate
Adjusting
Bracket
Flangedscrew
Mounting
Plate
Slot
AdjustingBracket
Locating Hole
Guide Tab
Knife Opening
LocatingPin
1-2 Getting Started
Step 2 - Level the Stacker
1. Check the distance between the rollers and the knife. Make
sure the rollers are not touching the front of the knife or too
far from the knife. If incorrect, follow the steps below. If
correct, skip this step and move on to Step 3 - Connect the
Power Cord.
The ideal position for the stacker is with the
end of tray slightly down.
2. Loosen the locking nuts with a wrench.
3. Make sure the stacker’s feet are flat
on a level surface.
You can raise or lower the feet
by turning them.
4. Evenly adjust both feet.
If the stacker is
utouching the knife case, lower the feet.
utoo far from the knife, raise the feet.
5. Tighten the locking nuts.
Rollers
Knife
Locking
Nuts
Getting Started 1-3
Step 3 - Connect the Power Cord
1. Plug the power cord into the stacker’s AC inlet.
2. Plug the other end of the power cord into a grounded outlet.
Once the power cord is attached to an outlet, the stacker is
on. There is no power ON/OFF switch for the stacker.
ACInlet
1-4 Getting Started
Step 4 - Check the Alignment
1. Load supply in the printer. For more information about
loading supply, refer to the printer’s Operator’s Handbook or
Quick Reference.
2. Set aside the tag weight.
3. Widen the guide rails to maximum width by pulling and
extending the guide rails out of the grooves at the bottom of
the tray.
4. Slide the rod ends of guide rails by using both hands to the
outer position.
GuideRails
Grooves
Getting Started 1-5
5. Move tag stop up and down by using your thumb to pull out
slightly on the release tab and lift up until it stops.
Adjust the tag stop to the length of the tags.
6. Make sure the transport lock handle is in the locked position.
7. Make sure supply is loaded and the printer is turned on.
8. Press the Feed or Cut button on the printer or keyboard
several times.
The supply should feed through the knife and tags should be
cut and placed in the stacker tray.
TagStop
TransportLock
1-6 Getting Started
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Avery Dennison Stampante
Avery Dennison
Avery Dennison MONARCH 9416 XL Manuale utente
Avery Dennison
Avery Dennison Monarch 9460 Manuale utente
Avery Dennison
Avery Dennison Monarch 938 Manuale utente
Avery Dennison
Avery Dennison Monarch ADTP1 Manuale utente
Avery Dennison
Avery Dennison Monarch 9906 Manuale utente
Avery Dennison
Avery Dennison TrafficJet Manuale
Avery Dennison
Avery Dennison Monarch 9433 Sierra Sport3 Manuale di servizio
Avery Dennison
Avery Dennison M09416 TTXLI Manuale utente
Avery Dennison
Avery Dennison Monarch ADTP2 EcoCut Manuale di servizio
Avery Dennison
Avery Dennison MONARCH 9416 XL Manuale utente
Avery Dennison
Avery Dennison Monarch 9419 Manuale di servizio
Avery Dennison
Avery Dennison Wireless Ethernet Print Server Monarch 7411 Manuale utente
Avery Dennison
Avery Dennison Monarch 9419 Manuale utente
Avery Dennison
Avery Dennison Pathfinder 6057 Manuale di servizio
Avery Dennison
Avery Dennison Monarch 9855 RFID Manuale di servizio
Avery Dennison
Avery Dennison Monarch 9855 Manuale utente
Avery Dennison
Avery Dennison Monarch Tabletop Printer 2 Manuale utente
Avery Dennison
Avery Dennison SNAP 700 Manuale operativo
Avery Dennison
Avery Dennison AP4.4 Manuale utente
Avery Dennison
Avery Dennison Monarch ADTP1 Manuale di servizio
