Badger Meter ORION Istruzioni per il montaggio

Installation &

Programming

Manual for Installer

BadgerMeter, Inc.

ORION®

Automated Meter

Reading System

Repeater

ORI-IOM-44

P/N 62014-070 Rev. 1

4-05

IMPORTANT: This manual contains important warnings

and information. READ AND KEEP FOR REFERENCE.

Disclaimer

The user/purchaser is expected to read and understand the information provided in this manual,

follow any listed safety precautions and instructions and keep this manual with the equipment for

future reference.

Misuse, mishandling and/or inadequate maintenance may impair performance and/or compromise

safety.

Questions or Service Assistance

If you have questions regarding the product or this document contact:

Badger Meter, Inc.

P.O. Box 245036

Milwaukee, WI 53224-9536

Telephone: (800) 456-5023

Fax: (888) 371-5982

On the Web: www.badgermeter.com

or call your local Badger Meter representative.

Table of Contents

Warning Label Information..........................................................................................................4

Scope of Manual.........................................................................................................................4

Product Unpacking and Inspection.............................................................................................4

Transmitter Description...............................................................................................................5

ORION®Repeater ......................................................................................................................5

Locating the Unit.........................................................................................................................5

Programming the Repeater ........................................................................................................5

Programming with a Laptop........................................................................................................6

Programming with a Badger®-Radix®.........................................................................................8

Specifications ...........................................................................................................................11

Regulatory................................................................................................................................11

WARNING LABEL INFORMATION

SCOPE of MANUAL

This manual contains installation instructions

for the ORION®Repeater for use with any

water or gas ORION transmitter.

Proper performance and reliability of the

ORION Repeater depends upon installation

in accordance with these instructions.

PRODUCT UNPACKING AND INSPECTION

Upon receipt of the product, perform the

following unpacking and inspection

procedures:

Carefully open the shipping package, follow

any instructions that may be marked on the

exterior. Remove all cushioning material

surrounding the product and carefully lift the

product from the package.

Retain the package and all packing material

for possible use in reshipment or storage.

Visually inspect the product and applicable

accessories for any physical damage such as

scratches, loose or broken parts, or any other

sign of damage that may have occurred

during shipment.

NOTE: communicates installation,

operation or maintenance

information that is safety

related but not hazard

related.

Note: If damage to the shipping container is evident

upon receipt, request the carrier to be present

when the product is unpacked.

Note: If damage is found, request an inspection by the

carrier’s agent within 48 hours of delivery and file

a claim with the carrier. A claim for equipment

damage in transit is the sole responsibility of the

purchaser.

TRANSMITTER DESCRIPTION

An ORION®transmitter is installed by a utility

on a consumer’s water or gas meter near or

in his/her home or business.

ORION REPEATER

The ORION Repeater is a

transmitter/receiver that can be used in

conjunction with any water or gas ORION

transmitter to increase the performance for

fixed network applications. Packaged in a

remote enclosure, the ORION Repeater can

be located in any indoor or non-submersed

outdoor application and programmed to

repeat up to five ORION transmitter signals

within receiving range of the ORION

Repeater.

ORION Repeaters are programmed to listen

to transmitters that are programmed into their

memory and to repeat the ORION standard

consumption message each time it is

received. Once an ORION Repeater repeats

a transmitter standard consumption

message, another ORION Repeater cannot

repeat the message.

The ORION Repeater is constructed of a

plastic remote enclosure with a ‘C’ sized

lithium battery that provides 15 years of

power for each ORION Repeater. The

ORION Repeater is shipped from the factory

in an off mode and is not transmitting. This

device can be shipped via aircraft shipment, if

necessary.

LOCATING THE UNIT

An ORION Repeater can be programmed

with up to five ORION water and/or gas

transmitter serial numbers. Once

programmed, the Repeater will listen for and

repeat the standard consumption messages

for those transmitters, which are located with

in range of the Repeater.

The ideal ORION Repeater location is

somewhere that has a clear “line-of-sight” to

the ORION gas or water transmitter.

However, this is rarely possible. The line-of-

sight may be hindered by obstructions such

as trees and vegetation, buildings and other

structures, vehicles or uneven terrain.

Note that the change of season, increasing

vegetation, building construction and

remolding can all contribute to changing the

signal reception over time.

PROGRAMMING THE ORION REPEATER

An ORION Repeater must be programmed in

the field in order to activate the device. Once

the ORION transmitter is installed, an ORION

Repeater can be installed within range of the

transmitter to increase the performance.

ORION Repeaters can be easily programmed

in the field using either the ORION Mobile

Reading Laptop or the Badger®-Radix®Data

Collector.

NOTE THAT WHEN THE ORION

PROGRAMMING ACCESSORY IS NOT IN

USE, IT SHOULD BE TURNED OFF TO

PREVENT UNINTENTIONAL

PROGRAMMING OF THE ORION

REPEATER.

PROGRAMMING WITH A LAPTOP

To program a Water Meter Transmitter Serial

Number into a Monitor with a laptop PC:

1. You will need a laptop computer

(p/n 65567) with ORION®Programmer

Version 1.2.14 or higher listed at the top

of the screen.

You will also need the following equipment:

Optical Programmer 64436-013

Programming Accessory 65589-001

ORION Transmitter

2. On the computer desktop, open the

ORION Laptop Programmer by double-

clicking the icon.

3. Connect the Optical programmer to the

9-pin connector on the laptop PC.

4. Place the Optical Programmer onto the

Programming Accessory.

NOTE: The Programming Accessory must be

read before any of the other buttons are

activated.

5. Select the [Read] button.

6. A message box appears saying,

The meter type is UNKNOWN.

Select [OK].

7. Select START RADIO.

8. On the laptop, move the cursor to the

Odometer Value box.

Select it.

9. Enter the Water Meter Transmitter

Serial Number into the Odometer Value

box.

NOTE: Do not enter the leading 7 of the

Transmitter Serial Number.

10. Place the Optical Programmer onto the

Programming Accessory or insure it is

still connected.

11. Select [Program Odometer] button.

12. A screen appears saying,

The meter type is UNKNOWN.

Select OK.

13. Swipe the programming magnet over

the bottom right corner of the ORION®

Repeater to put the unit into

programming mode. Once the ORION

Repeater has been put into

programming mode, it will listen for a

signal from the Programming Accessory

for up to 16 seconds. Once it

successfully hears the Programming

Accessory signal, the ORION Repeater

will verify it has been successfully

programmed by continuously

broadcasting the ORION transmitter

reading for one minute.

14. As soon as you are done programming

an ORION Repeater, it is important to

turn off your Programming Accessory.

Turn off the Programming Accessory by

properly positioning the Optical

Programmer on to the Programming

Accessory and selecting the [Stop

Radio] button.

NOTE: To erase all ORION serial

numbers in the repeater, program the

Program Accessory to a transmitter

number of ‘0’ and place the ORION

Repeater in programming mode using

the steps above.

To verify all ORION®transmitter serial

numbers in the repeater, swipe the

magnet across the programming

location on the ORION Repeater. BE

CERTAIN THAT THE PROGRAMMING

ACCESSORY IS EITHER TURNED

OFF OR NOT IN RANGE OF THE

ORION REPEATER PRIOR TO

SWIPING THE MAGNET ACROSS THE

PROGRAM LOCATION.

PROGRAMMING WITH BADGER® -RADIX®

To program a Water Meter Transmitter Serial

Number into a Monitor with a Badger-Radix

unit, you will need the following items:

Programming Accessory 65589-001

Water Meter Monitor 65567-001

ORION Transmitter

Badger-Radix Data Collector

1. Press and hold any key to turn on the

Badger-Radix Data Collector Unit.

2. At the “Main Menu”, select [Program &

Quick Read] <Q>.

3. Select [ORION] <O>

4. Select [Program] <P>

5. Place the Badger®-Radix®Data Collector

over the Programming Accessory.

NOTE: Verify the IR port (the oval shaped

hole on the bottom of the Badger-Radix

unit) is over the opening of the

Programming Accessory.

6. Select [Read] <R>

A message will appear on the screen “The

ORION®Transmitter has an invalid meter

type and needs to be returned to Badger

Meter for servicing.” Select OK <Enter>.

7. Select [Start Radio] <S>

8. Select <Enter>.

9. Remove the Badger-Radix unit from the

Programming Accessory.

10.Clear the Odometer Entry box.

Click the <Delete> key until the Odometer

Entry box is empty.

11.Use the keypad to enter Transmitter

Serial Number into the Odometer Entry

box.

NOTE: Do not enter the leading 7 of the

Transmitter Serial Number.

12.Again, place the Badger®-Radix®unit over

the Programming Accessory.

13.Select [Set Odometer] <O>.

14. Remove the Badger-Radix from the

Programming Accessory.

15. Swipe the programming magnet over

the bottom right corner of the ORION®

Repeater to put the unit into

programming mode. Once the ORION

Repeater has been put into

programming mode, it will listen for a

signal from the Programming Accessory

for up to 16 seconds. Once it

successfully hears the Programming

Accessory signal, the ORION Repeater

will verify it has been successfully

programmed by continuously

broadcasting the ORION transmitter

reading for one minute.

Altri manuali per ORION

Indice

Altri manuali Badger Meter Strumento di misura

Badger Meter

Badger Meter ORION Cellular LTE-M Manuale utente

Badger Meter

Badger Meter Dynasonics DXN Series Manuale per l'uso e la cura

Badger Meter

Badger Meter DN15 Manuale utente

Badger Meter

Badger Meter Dynasonics TFX-5000 Manuale utente

Badger Meter

Badger Meter Oval Gear EPM2-STD Manuale utente

Badger Meter

Badger Meter ER-500 Manuale del proprietario

Badger Meter

Badger Meter ModMAG M1000 Manuale utente

Badger Meter

Badger Meter ORION Mobile Read Guida all'installazione

Badger Meter

Badger Meter Blancett B220-880 Manuale utente

Badger Meter

Badger Meter M5000 Manuale utente

Badger Meter

Badger Meter Dynasonics DFX Series Manuale utente

Badger Meter

Badger Meter Recordall Turbo Series Manuale utente

Badger Meter

Badger Meter Recordall RTR Orion 3-Wire Manuale di installazione e d'uso

Badger Meter

Badger Meter 2100R+ Manuale utente

Badger Meter

Badger Meter E G2 Series Manuale utente

Badger Meter

Badger Meter ORION SE Manuale di installazione e d'uso

Badger Meter

Badger Meter LM-OG-P2 Advanced Manuale utente

Badger Meter

Badger Meter RCM 2000 Manuale utente

Badger Meter

Badger Meter ORION Manuale utente

Badger Meter

Badger Meter BadgerTouch HREBT Manuale utente

Badger Meter

Badger Meter IOG Series Manuale utente

Badger Meter

Badger Meter Blancett B220210 Manuale utente

Badger Meter

Badger Meter ModMAG M2000 Istruzioni operative

Badger Meter

Badger Meter Hedland PE Manuale utente

Manuali Strumento di misura popolari di altre marche

Suaoki

Suaoki D40 Manuale utente

Elster

Elster BK-G1.6 Manuale utente

Endress+Hauser

Endress+Hauser Deltabar FMD71 Manuale

Duratool

Duratool D03128 Manuale utente

Vega

Vega VEGAPULS 65 Manuale utente

Tonghui

Tonghui TH2618B Manuale utente

Tenmars

Tenmars TM-801 Manuale utente

MSR

MSR 145 Manuale utente

TPS

TPS WP-82 Manuale utente

ELMETRON

ELMETRON CP-511 Manuale utente

PCB Piezotronics

PCB Piezotronics 003C30 Manuale utente

Tenma

Tenma 72-10465 Manuale utente

Endress+Hauser

Endress+Hauser Proline Promag 50 Specifiche tecniche

Siemens

Siemens SITRANS F Coriolis FCT030 Manuale elenco delle parti

KLINGER

KLINGER CMF V Series Manuale utente

EXFO

EXFO FTB-2 Manuale operativo e di manutenzione

Keysight

Keysight M8290A Manuale utente

ADTEK

ADTEK MW-5 Manuale utente