BARRON EXITRONIX ILX Series Manuale utente

ILX SERIES

INSTALLATION INSTUCTIONS

800533.3948 •www.barronltg.com

10070073 Rev 1 - 03/14 1

SAVE THESE INSTRUCTIONS!

READ CAREFULLY AND FOLLOW ALL INSTRUCTIONS FOR YOUR OWN SAFETY

• DISCONNECT AC POWER SUPPLY BEFORE SERVICING.

• Installation and servicing of this equipment should be performed by qualified service personnel only.

• Ensure the electricity connections conform to the National Electrical Code and local regulations if applicable.

• Do not mount near gas or electrical heaters.

• Equipment should be mounted in locations and at heights where it will not readily be subjected to tampering by

unauthorized personnel.

• The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition. Any

modification or use of non-original components will void the warranty and product liability.

• Do not use this equipment for other than intended use.

INSTALLATION INSTRUCTIONS

120V AC

White – Common

Black – 120V

Green – Ground

277V AC

White – Common

Orange – 277V

Green –Ground

BACK MOUNTING

1. Remove faceplate and set aside.

2. Drill 3/8” hole into the center of the backplate. Drill 1/4” inch hole into the oblong indent on backplate that

corresponds with the junction box being used.

3. Feed leads through center hole and make the proper connections. All Electrical connections should be made inside

junction box.

Make Electrical connection as followed:

Note: Cap unused leads to prevent shorting.

4. Feed excess wire into junction box and secure backplate to junction box using screws provided with junction box.

5. Connect battery only after continuous AC power can be provided to unit. (If Applicable)

6. Snap in arrows to faceplate as required, storing unused arrows in safe place. Then snap faceplate to housing.

ILX SERIES

INSTALLATION INSTUCTIONS

800.533.3948 •www.barronltg.com

10070073 Rev 1 - 03/14 2

CEILING / END MOUNTING

1. Attach mounting plate to junction box.

2. Feed transformer leads through top hole, or side hole making

sure to secure wire into wire guides found at the edges of the

sign.

3. Attach sign to canopy by inserting canopy into sign then sliding

to the side to lock in plate.

4. All Electrical connection should be made inside junction box.

Make Electrical connection as followed:

Note: Cap unused leads to prevent shorting.

5. Push excess wire into junction box.

6. Connect battery only after continuous AC power can be provided to unit. (If applicable)

7. Secure canopy/exit sign assembly to junction box by inserting canopy into mounting plate, then sliding to the side to

lock in place.

8. Snap in arrows to faceplate as required storing unused arrows in a safe place. Then snap faceplate to housing.

9. For double-faced signs, replace backplate with extra “EXIT” faceplate.

OPERATION (Battery backup)

1. ApplyAC power to the unit. The LED indicator should turn RED.

2. After the battery has been left to charge for 24 hours, test the unit by pushing the switch. The LED indicator turns

OFF and the LED board stays ON.

3. When the switch is released, the LEDs turn OFF and the LED indicator turns back to RED.

TESTING

The Battery supplied with Battery backup model requires no maintenance. However, it should be tested periodically

and replace when it no longer operates the connected fixture for the duration of a 30-second or 90-minute test. The

battery supplied in this equipment has a life expectancy of 5 years when used in a normal ambient temperature of 72°F.

AC ONLY

RED 277VAC

BLACK 120VAC

WHITE COM

RED 277VAC

BLACK 120VAC

WHITE COM

LED BOARD

BAT POWER SUPPLY

PC BOARD

POWER SUPPLY

PC BOARD

BATTERY BACKUP

120V AC

White – Common

Black – 120V

Green – Ground

277V AC

White – Common

Orange – 277V

Green –Ground

Indice

Altri manuali BARRON Attrezzatura di illuminazione

BARRON

BARRON Speciality LED FBTCJ-24V Manuale utente

BARRON

BARRON Trace-Lite E110 Manuale utente

BARRON

BARRON TRACE-LITE RHL-ACR Manuale utente

BARRON

BARRON specialtyLED FTK Manuale utente

BARRON

BARRON EXITRONIX LL30 Series Manuale utente

BARRON

BARRON TRACE-LITE AXL2 Manuale utente

BARRON

BARRON Growlite GLB-315-A-120/277 Manuale utente

BARRON

BARRON TL301 Manuale utente

BARRON

BARRON TRACE-LITE WTA Series Manuale utente

BARRON

BARRON Exitronix 400U Series Manuale utente

BARRON

BARRON Trace-Lite AXL2 Manuale utente

BARRON

BARRON Exitronix SCL Series Manuale utente

BARRON

BARRON EXITRONIX VLEDC Series Manuale utente

BARRON

BARRON EXITRONIX SCL Series Manuale utente

BARRON

BARRON EXITRONIX 400WX Series Manuale utente

BARRON

BARRON GROWLITE GRM Manuale utente

BARRON

BARRON EXITRONIX 82 Series Manuale utente

BARRON

BARRON Exitronix LED-90 Series Manuale utente

BARRON

BARRON Exitronix CRL Series Manuale utente

BARRON

BARRON CP-EMW Series Manuale utente

BARRON

BARRON EXITRONIX LED-51 Series Manuale utente

BARRON

BARRON specialityLED RFX Manuale utente

BARRON

BARRON EXITRONIX CRL Series Manuale utente

BARRON

BARRON EXITRONIX VLED-90L Series Manuale utente

Manuali Attrezzatura di illuminazione popolari di altre marche

Brizo

Brizo 8SP-MU-4 Manuale utente

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Manuale utente

IKEA

IKEA BJÖRKSPIREA Manuale utente

Laserworld

Laserworld Evolution Series ES-400RGB Manuale utente

Alien

Alien RG STAR Manuale utente

EuroLite

EuroLite LED B-40 Manuale utente

Qazqa

Qazqa Suplux SL 3 Black 103062 Manuale utente

Commercial Electric

Commercial Electric 54568141 Manuale utente

CREE LIGHTING

CREE LIGHTING 304 Series Manuale utente

Goobay

Goobay 49867 Manuale utente

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Manuale utente

Alkalite

Alkalite Krypton KT-81 Manuale utente

Clas Ohlson

Clas Ohlson GU10 Manuale utente

DTS

DTS DELTA 10 F Manuale utente

ring

ring Solar Steplight Manuale utente

One Stop Gardens

One Stop Gardens 57696 Istruzioni per il montaggio

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Manuale utente

SIREM

SIREM Swimeo A2 Manuale utente