Bazzaz Z-Fi TC Manuale utente
INSTALLATION INSTRUCTIONS
HONDA CB1100 2013
T391S, T391R
WARNINGS > USING
• Use only in race or other closed-course applications and never on public roads.
• Z-Fi products are not certied by the California Air Resource Board (CARB) for
use on CA public lands.
WARNINGS > INSTALLING
• We strongly suggest that an experienced technician install this product.
• Read through all instructions before beginning installation.
• This document is intended for use by qualied technicians.
• This is not a replacement for the factory Engine Control Unit (ECU).
• Refer to a factory service manual for more specic stock component
identication/location information and removal/assembly procedures.
GETTING HELP
• Factory support is available in the US at 909-597-8300.
• For fastest support outside of the US, nd your local importer at bazzaz.net.
1>READ
UNLEASH.
THE SMARTEST PERFORMANCE TUNING TECHNOLOGY
R
FUEL + QUICKSHIFT + TRACTION CONTROL
INCLUDED PARTS
1. Z-Fi TC control unit
2. Fuel harness
3. Coil harness
4. Shift Switch and mounting hardware
5. USB cable
6. Speed Amplier
7. O2 eliminator
8. Scotchlok (1)
9. Zip ties
10.Velcro
2>IDENTIFY
FUEL HARNESS
MAIN
POWER
CKPS
GROUND LUG
TPS & INJECTORS
Z-AFM
CONNECTOR
MAP SELECT
NEUTRAL
10.
SPEED
COIL HARNESS
MAIN
SHIFT SWITCH
CONNECTOR
2>IDENTIFY (CONT.)
TC ADJUST SWITCH
CONNECTOR
COIL 1 (LEFT)
COIL 2 (RIGHT)
BAZZAZ SPEED AMPLIFIER
BAZZAZ SPEED
AMPLIFIER
WHEEL
SPEED
4>SECURE
1. Place the control unit in the battery tray, against the battery; the rubber
strap around the battery can be used to secure the control unit.
3>REMOVE
1. Seat
2. Fuel tank
3. Side panels
BAZZAZ
CONTROL UNIT
5>CONNECT
1. Connect the main connector of the Bazzaz
fuel harness to the control unit.
2. Route the fuel harness to the right side of
the motorcycle.
GROUND
5.1
COILS
NEUTRAL
CKPS
O2 SENSOR
SPEED
TPS &
INJECTORS
POWER
5>CONNECT (CONT.)
FACTORY
CONNECTOR
1. Locate the blue factory rear wheel speed sensor connector, found under
the airbox on the right side of the motorcycle.
2. Disconnect the wheel speed sensor connector from the factory harness for
ease of access.
3. Crimp a supplied Scotchlok onto the white wire of the disconnected factory
wheel speed sensor connector.
4. Locate the speed amplier provided in the Bazzaz kit.
5. Insert the mating (red) connector of the speed amplier into the Scotchlok.
6. Connect the Bazzaz speed connector from the Bazzaz fuel harness in-line
with the Bazzaz speed amplier connector.
7. Reconnect the wheel speed sensor connector to the factory harness.
5.2
SCOTCHLOK CRIMPED
ONTO WHITE WIRE
BAZZAZ
CONNECTOR
BAZZAZ
SPEED
AMPLIFIER
CONNECTOR
BAZZAZ
FUEL HARNESS
CONNECTOR
5>CONNECT (CONT.)
1. Continue routing the Bazzaz fuel harness along the same path as the factory
harness, up to the red factory Crank Position Sensor (CKPS) connectors.
2. Disconnect the factory CKPS connectors.
3. Connect the Bazzaz CKPS connectors in-line with the factory connectors.
1. Route the fuel harness forward, to the
factory neutral sensor connectors which
are found above the throttle bodies on the
right side.
2. Disconnect the factory neutral connectors.
3. Connect the Bazzaz neutral connectors
in-line with the factory connectors.
5.3
5.4
BAZZAZ
CONNECTORS
FACTORY
CONNECTORS
BAZZAZ
CONNECTORS
FACTORY
CONNECTORS
5>CONNECT (CONT.)
1. Route the remainder of the harness across to the left side of the motorcycle, under
the frame if possible.
2. Locate the large 10-pin subharness connectors (which are for the injector and Throt-
tle Position Sensor), found between the plastic shroud and frame.
3. Disconnect the factory 10-pin subharness connectors.
4. Connect the Bazzaz 10-pin connectors in-line with the factory 10-pin connectors.
5.5
6>GROUND
1. Route the Bazzaz ground lug
up to the factory ground lug,
found above and between the
two coil packs.
2. Secure the Bazzaz ground lug
with the factory ground lug.
BAZZAZ
CONNECTORS
FACTORY
CONNECTORS
7>CONNECT
1. Locate the factory red diagnostic connector (with a red cap on it), found
on the left side of the motorcycle, on the outside of the battery tray.
2. Remove the cap.
3. Connect the Bazzaz power connector into the factory connector.
4. Connect the cap onto the other Bazzaz Power connector.
7.1
BAZZAZ
CONNECTORS
FACTORY
CONNECTORS
7>CONNECT (CONT.)
COIL HARNESS
1. Connect the main connector of the Bazzaz coil harness to the Bazzaz
control unit.
2. Route the coil harness along the right side of the frame, to the front of
the motorcycle where the Bazzaz ground lug was installed.
3. Locate the 2 coil packs which can be hard to see in the photo. A bracket
with the ground lugs runs across the top of the coil packs.
4. Each coil pack has 2 spade posts, one with a green collar and the other
with a black collar.
5. The spade post with the green collar (on the left side of each coil pack)
is the one that you will be working with.
6. Disconnect the factory coil connector on each coil pack (has a rubber
boot around the connector) from the spade post with the green collar.
7. Connect the Bazzaz coil connectors in-line with the factory connector
and spade post on each coil pack.
7.2
BAZZAZ
CONNECTORS
BAZZAZ
CONNECTORS
FACTORY
CONNECTORS
