Beckhoff CX2500-0061 Manuale utente
Manual
CX2500-0061
Power over Ethernet (PoE) module
1.0
2016-07-13
Version:
Date:
Table of contents
Table of contents
1 Foreword ....................................................................................................................................................4
1.1 Notes on the documentation............................................................................................................. 4
1.2 Safety instructions ............................................................................................................................ 5
1.3 Documentation issue status.............................................................................................................. 5
2 Product overview.......................................................................................................................................6
2.1 Intended use ..................................................................................................................................... 6
2.2 System overview............................................................................................................................... 7
2.3 CX2500-0061 - Technical data ......................................................................................................... 8
3 Unpacking and transport ..........................................................................................................................9
4 Mounting and wiring ...............................................................................................................................10
4.1 Installing at the CX20x0 system ..................................................................................................... 10
4.2 Installing the bar clips ..................................................................................................................... 12
4.3 Installation on the mounting rail ...................................................................................................... 13
4.4 Ethernet interface (X610)................................................................................................................ 16
5 Error handling and diagnostics .............................................................................................................17
5.1 Diagnostic LEDs ............................................................................................................................. 17
5.2 Faults .............................................................................................................................................. 18
6 Removal and disposal.............................................................................................................................19
7 Appendix ..................................................................................................................................................21
7.1 Certifications ................................................................................................................................... 21
7.2 Support and Service ....................................................................................................................... 22
CX2500-0061 3Version: 1.0
Foreword
1 Foreword
1.1 Notes on the documentation
This description is only intended for the use of trained specialists in control and automation engineering who
are familiar with the applicable national standards.
It is essential that the following notes and explanations are followed when installing and commissioning
these components.
The responsible staff must ensure that the application or use of the products described satisfy all the
requirements for safety, including all the relevant laws, regulations, guidelines and standards.
Disclaimer
The documentation has been prepared with care. The products described are, however, constantly under
development.
For that reason the documentation is not in every case checked for consistency with performance data,
standards or other characteristics.
In the event that it contains technical or editorial errors, we retain the right to make alterations at any time
and without warning.
No claims for the modification of products that have already been supplied may be made on the basis of the
data, diagrams and descriptions in this documentation.
Trademarks
Beckhoff®, TwinCAT®, EtherCAT®, Safety over EtherCAT®, TwinSAFE®, XFC®and XTS® are registered
trademarks of and licensed by Beckhoff Automation GmbH.
Other designations used in this publication may be trademarks whose use by third parties for their own
purposes could violate the rights of the owners.
Patent Pending
The EtherCAT Technology is covered, including but not limited to the following patent applications and
patents:
EP1590927, EP1789857, DE102004044764, DE102007017835
with corresponding applications or registrations in various other countries.
The TwinCAT Technology is covered, including but not limited to the following patent applications and
patents:
EP0851348, US6167425 with corresponding applications or registrations in various other countries.
EtherCAT® is registered trademark and patented technology, licensed by Beckhoff Automation GmbH,
Germany
Copyright
© Beckhoff Automation GmbH & Co. KG, Germany.
The reproduction, distribution and utilization of this document as well as the communication of its contents to
others without express authorization are prohibited.
Offenders will be held liable for the payment of damages. All rights reserved in the event of the grant of a
patent, utility model or design.
CX2500-00614 Version: 1.0
Foreword
1.2 Safety instructions
Safety regulations
Please note the following safety instructions and explanations!
Product-specific safety instructions can be found on following pages or in the areas mounting, wiring,
commissioning etc.
Exclusion of liability
All the components are supplied in particular hardware and software configurations appropriate for the
application. Modifications to hardware or software configurations other than those described in the
documentation are not permitted, and nullify the liability of Beckhoff Automation GmbH & Co. KG.
Personnel qualification
This description is only intended for trained specialists in control, automation and drive engineering who are
familiar with the applicable national standards.
Description of symbols
In this documentation the following symbols are used with an accompanying safety instruction or note. The
safety instructions must be read carefully and followed without fail!
DANGER
Serious risk of injury!
Failure to follow the safety instructions associated with this symbol directly endangers the
life and health of persons.
WARNING
Risk of injury!
Failure to follow the safety instructions associated with this symbol endangers the life and
health of persons.
CAUTION
Personal injuries!
Failure to follow the safety instructions associated with this symbol can lead to injuries to
persons.
Attention
Damage to the environment or devices
Failure to follow the instructions associated with this symbol can lead to damage to the en-
vironment or equipment.
Note
Tip or pointer
This symbol indicates information that contributes to better understanding.
1.3 Documentation issue status
Version Changes
1.0 First version
CX2500-0061 5Version: 1.0
Product overview
2 Product overview
2.1 Intended use
The CX20x0 device series is a modular control system designed for DIN rail installation. The system is
scalable, so that the required modules can be assembled and installed in the control cabinet or terminal box
as required.
Only switch the PC off after closing the software
Before the Embedded PC is switched off, the software currently running on it should be stopped properly in
order to avoid data loss on the hard disk. Please read the section on “Switching off”.
Switch off all system components and uncouple the Industrial PC from the system if the PC is not used for
control purposes, e.g. during a function test. To disconnect first pull the first terminal behind the power
supply unit (optional), then pull the connectors of the fieldbus connections.
System components that have been switched off must be secured against being switched on again.
The Embedded PC’s power supply unit must be supplied with 24VDC.
Attention
Damage to the environment or devices
Do not exchange any parts when under power! The exchange of controller parts when live
can lead to short-circuits or overvoltages. These can damage the controller itself and con-
nected peripherals (terminals, monitors, input devices, etc.).
When components are being fitted or removed, the supply voltage must be switched off.
Software knowledge
Attention
System malfunctions
Mandatory software knowledge! Every user must be familiar with any of the functions of the
software installed on the PC that he can reach.
CX2500-00616 Version: 1.0
Product overview
2.2 System overview
The system modules for the CX2000 family are connected to the CPU on the left-hand side via a multi-pin
connector. Internally they are connected via PCI Express. Up to four modules can be connected in any
order.
The CX2500-0020 audio module has jack plug (5 x 3.5 mm) and cinch plug for digital signals (SPDIF). Up to
7.1 multi-channel audio can be used. Serial interfaces can be added with the modules CX2500-0030
(RS232) and CX2500-0031 (RS422/RS485). The CX2500-0060 module provides two further independent
Gbit Ethernet interfaces. The CX2500-0070 module can be used to add up to four further USB 3.0 interfaces.
Power over Ethernet (PoE) module CX2500-0061
The CX2500-0061 Power over Ethernet module supports devices with PoE class 0, 1, 2, 3 and 4 in
accordance with the PoE standard IEEE 802.3af-2003. The maximum PoE power output is 15.4 W. The PoE
supply voltage is generated internally, no external power supply is necessary. In the case of an overload of
the CX2500-0061, the PoE supply shuts down for two seconds, then restarts. The diagnostic LEDs PWR,
PoE, PM1 and PM2 provide information about the type of PoE supply (mode A or B) as well as about the
PoE class reported by the powered device.
CX2500-0061 7Version: 1.0
Product overview
2.3 CX2500-0061 - Technical data
Dimensions
The system module CX2500-0061 provides a further Power over Ethernet (PoE) interface for the CX20x0.
Technical data CX2500-0061
Interfaces 1 x RJ45, 10/100/1000 MBit/s with Power-over-Ethernet (PoE)
max. PoE power delivery 15,4 W
Supported devices Devices of PoE Class 0, 1, 2, 3 and 4 as defined by PoE standard IEEE
802.3af-2003
Power supply via system bus (through CX2100-0xxx power supply modules)
internal generation of PoE supply voltage (no external 48 V power feeding
required)
max. Power loss 3 W
Dielectric strength 500 V (supply / internal electronics)
Dimensions (W x H x D) 24 mm x 99 mm x 54,5 mm
Weight approx. 208 g
Operating/storage temperature -25° C ... +60° C / -40° C ... +85° C
Relative humidity 95 %, no condensation
Vibration/shock resistance conforms to EN 60068-2-6/EN 60068-2-27
EMC immunity/emission conforms to EN 61000-6-2/EN 61000-6-4
Protection class IP 20
Further Information: www.beckhoff.de/CX2000
CX2500-00618 Version: 1.0
Unpacking and transport
3 Unpacking and transport
Note
Short circuit due to moisture
Moisture can lead to short circuits. Moisture can form during transport in cold weather or in
the event of large temperature fluctuations.
Avoid moisture formation (condensation) in the device, and leave the device to adjust to
room temperature slowly. If condensation has occurred, wait at least 12 hours before
switching on the device.
Proceed as follows to unpack the unit:
1. Remove packaging.
2. Do not discard the original packaging. Keep it for transporting the device in the future.
3. Check the delivery for completeness by comparing it with your order.
4. Please keep the associated paperwork. It contains important information for handling the unit.
5. Check the contents for visible shipping damage.
6. If you notice any shipping damage or inconsistencies between the contents and your order, you should
notify Beckhoff Service.
Shipping and relocation
Despite the robust design of the unit, the components are sensitive to strong vibrations and impacts.
Therefore, during transport please protect your device from:
• mechanical stress and
• use the original packaging.
Follow the specified storage conditions for the device and store it at temperatures between -40 °C and +85
°C.
CX2500-0061 9Version: 1.0
Mounting and wiring
4 Mounting and wiring
4.1 Installing at the CX20x0 system
Note
Damage to the contacts
Incorrect installation may result in damage to the contacts of the system modules.
The system modules may only be attached on the left-hand side of the basic CPU module.
A maximum of four system modules can be attached to the basic CPU module via the internal PCI Express
bus. In delivery state the system module is equipped with a protective cap for the bus connector.
Before continuing, connect the system module to the basic CPU module.
Prerequisites for this step:
• Exit the software and shut down the CX20x0 hardware configuration.
• Switch off the power supply.
Install the system module as follows:
1. Put a screwdriver into the recess on the short side of the protective cap and lever it off.
2. Remove the protective cap to expose the bus connector.
3. Insert the system module on the left-hand side of the basic CPU module.
CX2500-006110 Version: 1.0
Indice
Altri manuali Beckhoff Unità di controllo
Beckhoff
Beckhoff AX8000 Manuale utente
Beckhoff
Beckhoff PS9011-2420-0001 Manuale dell'operatore
Beckhoff
Beckhoff C9900-M900 Guida utente
Beckhoff
Beckhoff EtherCAT Box Manuale utente
Beckhoff
Beckhoff C9900-M Series Guida utente
Beckhoff
Beckhoff EM2042 Manuale dell'operatore
Beckhoff
Beckhoff AX5021 Manuale dell'operatore
Beckhoff
Beckhoff EP3204 Manuale dell'operatore
Beckhoff
Beckhoff KM4602 Manuale dell'operatore
Beckhoff
Beckhoff CX2550 Series Manuale utente
Beckhoff
Beckhoff KM6551 Manuale dell'operatore
Beckhoff
Beckhoff EP6002 Manuale dell'operatore
Beckhoff
Beckhoff EP1 Series Manuale dell'operatore
Beckhoff
Beckhoff M310 Manuale utente
Beckhoff
Beckhoff AX2090-TS50-3000 Manuale dell'operatore
Beckhoff
Beckhoff PS2001-2420-0000 Manuale dell'operatore
Beckhoff
Beckhoff EK9500 Manuale dell'operatore
Beckhoff
Beckhoff EJ7211-0010 Manuale dell'operatore
Beckhoff
Beckhoff AX2090-MD50 Series Manuale dell'operatore
Beckhoff
Beckhoff C9900-M800 Manuale utente
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
